Page organisation in this revision
- Page type
- Reference hub
- Subject
- Engine ECU
- Parent
- MoTeC standalone ECUs
- Applies to
- No ECU-specific applicability
- Tool groups
- None
- Manufacturers
- None
Changes from revision 2 to revision 3
Removed text is struck through; added text is highlighted.
MoTeC M2R, part 10006, is an earlier Gold Box engine controller listed in MoTeC's obsolete-product archive. Dedicated two-rotor application. Manufacturer Gold Box archive; manufacturer model glossary.
Identification and compatibility
Read the full ECU part number, connector, firmware, options and the label before identifying the correct model. Configurations and optional engine packages vary; a similar suffix, physical plug or a common calibration does not establish a universal pinout or exact cylinder capability. The manufacturer's archived product listing provides M2R-specific documentation.
Pinout and software
Consult the MoTeC M2R product and wiring downloads and MoTeC legacy downloads. Model and marine-labelled variants must be checked against their own part numbers, connector drawings and firmware. Confirm connector orientation and the complete power, ground, sensor, injector and ignition circuits with the original documentation before wiring.
These units use a legacy ECU Manager or EMP software generation appropriate to the exact controller and firmware; M1 Tune is for M1 products. See MoTeC software archive and the MoTeC manufacturer guide.
Manufacturer M2R connector schedule
From MoTeC document DVIN0018, M2R Installation Notes, page 2, reproduced by a document mirror. The manufacturer labels the connector diagram as looking into the ECU. Positions omitted in the source table are marked “Not listed”; this does not establish that they are electrically unused. Ignition functions vary with the documented rotary mode.
A structured, redrawn version of the manufacturer pin table is in MoTeC M2R connector pinout.M2R pinManufacturer signal labelFunction112V12 V switched, ECU relay2INJ1Injector 1 primary3INJ2Injector 2 primary45V ENG5 V sensor supply5REF HallReference sensor Hall6REF MagReference sensor magnetic7SYNC HallSync sensor Hall8SYNC MagSync sensor magnetic9—Not listed in source10—Not listed in source11—Not listed in source12—Not listed in source13AUX1Tacho / fuel pump14INJ3Injector 1 secondary15INJ4Injector 2 secondary16TPThrottle position17MAPManifold pressure18AUX VSpare19DIG1Spare20DIG2Spare21—Not listed in source22RS232 TXCommunications23RS232 RXCommunications24—Not listed in source25GNDECU earth268V ENG8 V supply270V ENG0 V sensor supply28ETEngine temperature29ATAir temperature30AUX TSpare31LA+Lambda positive32LA−Lambda negative33IGN1Ignition 1 and 2 leading, mode 102/103; ignition 1 leading, mode 140/14134AUX2Ignition 1 trailing, mode 102; ignition 1 and 2 trailing, mode 103; ignition 2 leading, mode 140/14135AUX3Ignition 2 trailing, mode 102; trailing logic select, mode 103; ignition 1 trailing, mode 140/14136AUX4Ignition 2 trailing, mode 140/141; fuel pump
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 2: MoTeC M2R
MoTeC M2R, part 10006, is an earlier Gold Box engine controller listed in MoTeC's obsolete-product archive. Dedicated two-rotor application. Manufacturer Gold Box archive; manufacturer model glossary.
Identification and compatibility
Read the full ECU part number, connector, firmware, options and the label before identifying the correct model. Configurations and optional engine packages vary; a similar suffix, physical plug or a common calibration does not establish a universal pinout or exact cylinder capability. The manufacturer's archived product listing provides M2R-specific documentation.
Pinout and software
Consult the MoTeC M2R product and wiring downloads and MoTeC legacy downloads. Model and marine-labelled variants must be checked against their own part numbers, connector drawings and firmware. Confirm connector orientation and the complete power, ground, sensor, injector and ignition circuits with the original documentation before wiring.
These units use a legacy ECU Manager or EMP software generation appropriate to the exact controller and firmware; M1 Tune is for M1 products. See MoTeC software archive and the MoTeC manufacturer guide.
Manufacturer M2R connector schedule
From MoTeC document DVIN0018, M2R Installation Notes, page 2, reproduced by a document mirror. The manufacturer labels the connector diagram as looking into the ECU. Positions omitted in the source table are marked “Not listed”; this does not establish that they are electrically unused. Ignition functions vary with the documented rotary mode.
| M2R pin | Manufacturer signal label | Function |
|---|
| 1 | 12V | 12 V switched, ECU relay |
| 2 | INJ1 | Injector 1 primary |
| 3 | INJ2 | Injector 2 primary |
| 4 | 5V ENG | 5 V sensor supply |
| 5 | REF Hall | Reference sensor Hall |
| 6 | REF Mag | Reference sensor magnetic |
| 7 | SYNC Hall | Sync sensor Hall |
| 8 | SYNC Mag | Sync sensor magnetic |
| 9 | — | Not listed in source |
| 10 | — | Not listed in source |
| 11 | — | Not listed in source |
| 12 | — | Not listed in source |
| 13 | AUX1 | Tacho / fuel pump |
| 14 | INJ3 | Injector 1 secondary |
| 15 | INJ4 | Injector 2 secondary |
| 16 | TP | Throttle position |
| 17 | MAP | Manifold pressure |
| 18 | AUX V | Spare |
| 19 | DIG1 | Spare |
| 20 | DIG2 | Spare |
| 21 | — | Not listed in source |
| 22 | RS232 TX | Communications |
| 23 | RS232 RX | Communications |
| 24 | — | Not listed in source |
| 25 | GND | ECU earth |
| 26 | 8V ENG | 8 V supply |
| 27 | 0V ENG | 0 V sensor supply |
| 28 | ET | Engine temperature |
| 29 | AT | Air temperature |
| 30 | AUX T | Spare |
| 31 | LA+ | Lambda positive |
| 32 | LA− | Lambda negative |
| 33 | IGN1 | Ignition 1 and 2 leading, mode 102/103; ignition 1 leading, mode 140/141 |
| 34 | AUX2 | Ignition 1 trailing, mode 102; ignition 1 and 2 trailing, mode 103; ignition 2 leading, mode 140/141 |
| 35 | AUX3 | Ignition 2 trailing, mode 102; trailing logic select, mode 103; ignition 1 trailing, mode 140/141 |
| 36 | AUX4 | Ignition 2 trailing, mode 140/141; fuel pump |
Revision 3: MoTeC M2R
MoTeC M2R, part 10006, is an earlier Gold Box engine controller listed in MoTeC's obsolete-product archive. Dedicated two-rotor application. Manufacturer Gold Box archive; manufacturer model glossary.
Identification and compatibility
Read the full ECU part number, connector, firmware, options and the label before identifying the correct model. Configurations and optional engine packages vary; a similar suffix, physical plug or a common calibration does not establish a universal pinout or exact cylinder capability. The manufacturer's archived product listing provides M2R-specific documentation.
Pinout and software
Consult the MoTeC M2R product and wiring downloads and MoTeC legacy downloads. Model and marine-labelled variants must be checked against their own part numbers, connector drawings and firmware. Confirm connector orientation and the complete power, ground, sensor, injector and ignition circuits with the original documentation before wiring.
These units use a legacy ECU Manager or EMP software generation appropriate to the exact controller and firmware; M1 Tune is for M1 products. See MoTeC software archive and the MoTeC manufacturer guide.
Manufacturer M2R connector schedule
From MoTeC document DVIN0018, M2R Installation Notes, page 2, reproduced by a document mirror. The manufacturer labels the connector diagram as looking into the ECU. Positions omitted in the source table are marked “Not listed”; this does not establish that they are electrically unused. Ignition functions vary with the documented rotary mode.
A structured, redrawn version of the manufacturer pin table is in MoTeC M2R connector pinout.
| M2R pin | Manufacturer signal label | Function |
|---|
| 1 | 12V | 12 V switched, ECU relay |
| 2 | INJ1 | Injector 1 primary |
| 3 | INJ2 | Injector 2 primary |
| 4 | 5V ENG | 5 V sensor supply |
| 5 | REF Hall | Reference sensor Hall |
| 6 | REF Mag | Reference sensor magnetic |
| 7 | SYNC Hall | Sync sensor Hall |
| 8 | SYNC Mag | Sync sensor magnetic |
| 9 | — | Not listed in source |
| 10 | — | Not listed in source |
| 11 | — | Not listed in source |
| 12 | — | Not listed in source |
| 13 | AUX1 | Tacho / fuel pump |
| 14 | INJ3 | Injector 1 secondary |
| 15 | INJ4 | Injector 2 secondary |
| 16 | TP | Throttle position |
| 17 | MAP | Manifold pressure |
| 18 | AUX V | Spare |
| 19 | DIG1 | Spare |
| 20 | DIG2 | Spare |
| 21 | — | Not listed in source |
| 22 | RS232 TX | Communications |
| 23 | RS232 RX | Communications |
| 24 | — | Not listed in source |
| 25 | GND | ECU earth |
| 26 | 8V ENG | 8 V supply |
| 27 | 0V ENG | 0 V sensor supply |
| 28 | ET | Engine temperature |
| 29 | AT | Air temperature |
| 30 | AUX T | Spare |
| 31 | LA+ | Lambda positive |
| 32 | LA− | Lambda negative |
| 33 | IGN1 | Ignition 1 and 2 leading, mode 102/103; ignition 1 leading, mode 140/141 |
| 34 | AUX2 | Ignition 1 trailing, mode 102; ignition 1 and 2 trailing, mode 103; ignition 2 leading, mode 140/141 |
| 35 | AUX3 | Ignition 2 trailing, mode 102; trailing logic select, mode 103; ignition 1 trailing, mode 140/141 |
| 36 | AUX4 | Ignition 2 trailing, mode 140/141; fuel pump |