Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Gearboxes
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Changes from revision 2 to revision 2

Removed text is struck through; added text is highlighted.

ZF AS Tronic is a family of electronically controlled automated manual transmissions for commercial vehicles. This guide uses the DAF DAVIE XD diagnostic manual, AS Tronic chapter, issue 200438, as a specific historical truck example, together with ZF service guidance. It is not a universal fault-code reference for every DAF, Iveco, MAN, bus or later ZF TraXon gearbox. Confirm vehicle VIN, gearbox type, controller, software, actuators and current service information. DAF DAVIE XD diagnostics manual, AS Tronic sections 1–2.

How to identify the system

AS Tronic automates clutch and gearbox operation; the particular DAF material describes pneumatic actuation, position feedback, a modulator and communication with other vehicle controllers. Some derivatives and installations use different release mechanisms, actuator equipment or diagnostic software. A shared ZF name or shift display is not sufficient to transfer a fluid, air-pressure figure, code, component or calibration procedure to another vehicle. ZF lists wiring and pneumatic inspection, transmission and clutch actuators and diagnostic-tool functions separately in its AS Tronic bus repair-manual contents.

What the clutch data means

The DAF DAVIE XD clutch-actuator menu distinguishes absolute position in millimetres, relative position as a percentage, and whether the clutch is reported open, closed or slipping. In its specific example, the displayed relative position approaches 100% when closed and 0% when open. This convention is not a universal clutch-wear percentage and must not be assumed for another scanner or vehicle. DAF explains that the actual open and closed positions move through the actuator operating range as the friction plate wears; interpret both endpoints, travel and status with the correct test report. DAF DAVIE XD system inspection, section 2.3.

The same manual distinguishes a stationary selector-position test from a dynamic loaded test, with a report and reference positions for the particular gearbox. Run either only with the correct equipment, conditions and safety procedure; position data alone does not prove that a clutch or gearbox component is defective.

Documented fault examples

DAF issue 200438 exampleWhat to distinguish 190 — missing or incorrect engine-speed signal over CANThe DAF note describes a time-controlled clutch strategy with abrupt engagement and loss of automatic mode in its example. Compare engine-speed messaging and relevant engine/network faults before concluding that the clutch actuator is defective. 3107 — clutch travel-sensor supply issueThe DAF example describes reduced clutch control and loss of automatic mode. Check the specified supply, connections and feedback with the correct diagnostic plan; the code alone is not a replacement-parts verdict. 3117 — no clutch-position change during teach-inDAF lists several possible branches, including actuator or modulator faults, harness and sensor or speed signals. An aborted learn-in is not proof of a worn clutch. 3136 — gate-position teach-in faultThe note treats actuator-position feedback and air-pressure availability as distinct conditions. Capture the exact self-test result and inspect the commanded movement, air and relevant sensor evidence. 3026/3027 — engine configuration information over CANDAF describes possible shift-quality effects from a missing or incorrect message. Scan other relevant control units and verify configuration and network communication under the applicable test plan.

These are DAF DAVIE codes and descriptions in the cited issue, not generic OBD P-codes or universal AS Tronic fault mappings. A fallback described in the manual does not prove that another controller will behave identically. DAF AS Tronic fault code descriptions, section 1.2.

Air-system contamination: ZF SACHS service information 12847 EN identifies moisture and corrosion in the compressed-air system as possible causes of commercial-vehicle clutch-actuator malfunction. It lists inadequate air-drier maintenance, water in the air reservoir, high air consumption and compressor-oil contamination of the drier medium as possible contributors. On a pneumatic installation, include the vehicle air system in the applicable fault-directed checks; this general bulletin does not identify the illustrated actuator as fitted to every DAF or establish a fault on a particular truck.

Mechanical release and workshop sequence

ZF states that wear in a release fork, shaft, bearing or guide can affect release travel or alignment and cause shifting or clutch problems, including on AS Tronic applications. Diagnose the complete release mechanism as directed rather than treating an actuator-related symptom as proof of an electronic failure. ZF Aftermarket release-system guidance.

Record the complaint, selected gear, load, operating temperature, warning, exact vehicle/ECU identification and previous clutch, gearbox or software work. Preserve active and stored faults, states and time context before clearing them.Use the applicable DAF or vehicle-manufacturer diagnostic plan to compare request, actual selected gear, clutch position and status, speed and relevant network data. Check supply, wiring and the specified compressed-air supply or other actuation circuit for the actual installation.Inspect the actuator and mechanical release or gearbox only where the fault tree and measured evidence direct. The service procedure may require calibration after particular work; do not use teach-in as a substitute for fixing air, mechanical or electrical faults.Secure the truck and use the manufacturer's safety and isolation procedure: compressed-air circuits can retain energy, and active tests can move the transmission or clutch. Verify the original fault after the specified repair.

See ZF TraXon and ConAct for a different release arrangement, Eaton UltraShift PLUS and the electronic gearbox index.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 2: ZF AS Tronic DAF automated gearbox operation and diagnosis

ZF AS Tronic is a family of electronically controlled automated manual transmissions for commercial vehicles. This guide uses the DAF DAVIE XD diagnostic manual, AS Tronic chapter, issue 200438, as a specific historical truck example, together with ZF service guidance. It is not a universal fault-code reference for every DAF, Iveco, MAN, bus or later ZF TraXon gearbox. Confirm vehicle VIN, gearbox type, controller, software, actuators and current service information. DAF DAVIE XD diagnostics manual, AS Tronic sections 1–2.

How to identify the system

AS Tronic automates clutch and gearbox operation; the particular DAF material describes pneumatic actuation, position feedback, a modulator and communication with other vehicle controllers. Some derivatives and installations use different release mechanisms, actuator equipment or diagnostic software. A shared ZF name or shift display is not sufficient to transfer a fluid, air-pressure figure, code, component or calibration procedure to another vehicle. ZF lists wiring and pneumatic inspection, transmission and clutch actuators and diagnostic-tool functions separately in its AS Tronic bus repair-manual contents.

What the clutch data means

The DAF DAVIE XD clutch-actuator menu distinguishes absolute position in millimetres, relative position as a percentage, and whether the clutch is reported open, closed or slipping. In its specific example, the displayed relative position approaches 100% when closed and 0% when open. This convention is not a universal clutch-wear percentage and must not be assumed for another scanner or vehicle. DAF explains that the actual open and closed positions move through the actuator operating range as the friction plate wears; interpret both endpoints, travel and status with the correct test report. DAF DAVIE XD system inspection, section 2.3.

The same manual distinguishes a stationary selector-position test from a dynamic loaded test, with a report and reference positions for the particular gearbox. Run either only with the correct equipment, conditions and safety procedure; position data alone does not prove that a clutch or gearbox component is defective.

Documented fault examples

DAF issue 200438 exampleWhat to distinguish
190 — missing or incorrect engine-speed signal over CANThe DAF note describes a time-controlled clutch strategy with abrupt engagement and loss of automatic mode in its example. Compare engine-speed messaging and relevant engine/network faults before concluding that the clutch actuator is defective.
3107 — clutch travel-sensor supply issueThe DAF example describes reduced clutch control and loss of automatic mode. Check the specified supply, connections and feedback with the correct diagnostic plan; the code alone is not a replacement-parts verdict.
3117 — no clutch-position change during teach-inDAF lists several possible branches, including actuator or modulator faults, harness and sensor or speed signals. An aborted learn-in is not proof of a worn clutch.
3136 — gate-position teach-in faultThe note treats actuator-position feedback and air-pressure availability as distinct conditions. Capture the exact self-test result and inspect the commanded movement, air and relevant sensor evidence.
3026/3027 — engine configuration information over CANDAF describes possible shift-quality effects from a missing or incorrect message. Scan other relevant control units and verify configuration and network communication under the applicable test plan.

These are DAF DAVIE codes and descriptions in the cited issue, not generic OBD P-codes or universal AS Tronic fault mappings. A fallback described in the manual does not prove that another controller will behave identically. DAF AS Tronic fault code descriptions, section 1.2.

Air-system contamination: ZF SACHS service information 12847 EN identifies moisture and corrosion in the compressed-air system as possible causes of commercial-vehicle clutch-actuator malfunction. It lists inadequate air-drier maintenance, water in the air reservoir, high air consumption and compressor-oil contamination of the drier medium as possible contributors. On a pneumatic installation, include the vehicle air system in the applicable fault-directed checks; this general bulletin does not identify the illustrated actuator as fitted to every DAF or establish a fault on a particular truck.

Mechanical release and workshop sequence

ZF states that wear in a release fork, shaft, bearing or guide can affect release travel or alignment and cause shifting or clutch problems, including on AS Tronic applications. Diagnose the complete release mechanism as directed rather than treating an actuator-related symptom as proof of an electronic failure. ZF Aftermarket release-system guidance.

  1. Record the complaint, selected gear, load, operating temperature, warning, exact vehicle/ECU identification and previous clutch, gearbox or software work. Preserve active and stored faults, states and time context before clearing them.
  2. Use the applicable DAF or vehicle-manufacturer diagnostic plan to compare request, actual selected gear, clutch position and status, speed and relevant network data. Check supply, wiring and the specified compressed-air supply or other actuation circuit for the actual installation.
  3. Inspect the actuator and mechanical release or gearbox only where the fault tree and measured evidence direct. The service procedure may require calibration after particular work; do not use teach-in as a substitute for fixing air, mechanical or electrical faults.
  4. Secure the truck and use the manufacturer's safety and isolation procedure: compressed-air circuits can retain energy, and active tests can move the transmission or clutch. Verify the original fault after the specified repair.

See ZF TraXon and ConAct for a different release arrangement, Eaton UltraShift PLUS and the electronic gearbox index.

Revision 2: ZF AS Tronic DAF automated gearbox operation and diagnosis

ZF AS Tronic is a family of electronically controlled automated manual transmissions for commercial vehicles. This guide uses the DAF DAVIE XD diagnostic manual, AS Tronic chapter, issue 200438, as a specific historical truck example, together with ZF service guidance. It is not a universal fault-code reference for every DAF, Iveco, MAN, bus or later ZF TraXon gearbox. Confirm vehicle VIN, gearbox type, controller, software, actuators and current service information. DAF DAVIE XD diagnostics manual, AS Tronic sections 1–2.

How to identify the system

AS Tronic automates clutch and gearbox operation; the particular DAF material describes pneumatic actuation, position feedback, a modulator and communication with other vehicle controllers. Some derivatives and installations use different release mechanisms, actuator equipment or diagnostic software. A shared ZF name or shift display is not sufficient to transfer a fluid, air-pressure figure, code, component or calibration procedure to another vehicle. ZF lists wiring and pneumatic inspection, transmission and clutch actuators and diagnostic-tool functions separately in its AS Tronic bus repair-manual contents.

What the clutch data means

The DAF DAVIE XD clutch-actuator menu distinguishes absolute position in millimetres, relative position as a percentage, and whether the clutch is reported open, closed or slipping. In its specific example, the displayed relative position approaches 100% when closed and 0% when open. This convention is not a universal clutch-wear percentage and must not be assumed for another scanner or vehicle. DAF explains that the actual open and closed positions move through the actuator operating range as the friction plate wears; interpret both endpoints, travel and status with the correct test report. DAF DAVIE XD system inspection, section 2.3.

The same manual distinguishes a stationary selector-position test from a dynamic loaded test, with a report and reference positions for the particular gearbox. Run either only with the correct equipment, conditions and safety procedure; position data alone does not prove that a clutch or gearbox component is defective.

Documented fault examples

DAF issue 200438 exampleWhat to distinguish
190 — missing or incorrect engine-speed signal over CANThe DAF note describes a time-controlled clutch strategy with abrupt engagement and loss of automatic mode in its example. Compare engine-speed messaging and relevant engine/network faults before concluding that the clutch actuator is defective.
3107 — clutch travel-sensor supply issueThe DAF example describes reduced clutch control and loss of automatic mode. Check the specified supply, connections and feedback with the correct diagnostic plan; the code alone is not a replacement-parts verdict.
3117 — no clutch-position change during teach-inDAF lists several possible branches, including actuator or modulator faults, harness and sensor or speed signals. An aborted learn-in is not proof of a worn clutch.
3136 — gate-position teach-in faultThe note treats actuator-position feedback and air-pressure availability as distinct conditions. Capture the exact self-test result and inspect the commanded movement, air and relevant sensor evidence.
3026/3027 — engine configuration information over CANDAF describes possible shift-quality effects from a missing or incorrect message. Scan other relevant control units and verify configuration and network communication under the applicable test plan.

These are DAF DAVIE codes and descriptions in the cited issue, not generic OBD P-codes or universal AS Tronic fault mappings. A fallback described in the manual does not prove that another controller will behave identically. DAF AS Tronic fault code descriptions, section 1.2.

Air-system contamination: ZF SACHS service information 12847 EN identifies moisture and corrosion in the compressed-air system as possible causes of commercial-vehicle clutch-actuator malfunction. It lists inadequate air-drier maintenance, water in the air reservoir, high air consumption and compressor-oil contamination of the drier medium as possible contributors. On a pneumatic installation, include the vehicle air system in the applicable fault-directed checks; this general bulletin does not identify the illustrated actuator as fitted to every DAF or establish a fault on a particular truck.

Mechanical release and workshop sequence

ZF states that wear in a release fork, shaft, bearing or guide can affect release travel or alignment and cause shifting or clutch problems, including on AS Tronic applications. Diagnose the complete release mechanism as directed rather than treating an actuator-related symptom as proof of an electronic failure. ZF Aftermarket release-system guidance.

  1. Record the complaint, selected gear, load, operating temperature, warning, exact vehicle/ECU identification and previous clutch, gearbox or software work. Preserve active and stored faults, states and time context before clearing them.
  2. Use the applicable DAF or vehicle-manufacturer diagnostic plan to compare request, actual selected gear, clutch position and status, speed and relevant network data. Check supply, wiring and the specified compressed-air supply or other actuation circuit for the actual installation.
  3. Inspect the actuator and mechanical release or gearbox only where the fault tree and measured evidence direct. The service procedure may require calibration after particular work; do not use teach-in as a substitute for fixing air, mechanical or electrical faults.
  4. Secure the truck and use the manufacturer's safety and isolation procedure: compressed-air circuits can retain energy, and active tests can move the transmission or clutch. Verify the original fault after the specified repair.

See ZF TraXon and ConAct for a different release arrangement, Eaton UltraShift PLUS and the electronic gearbox index.