Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Lamborghini Gallardo LP520 S12, with product code S12-LAM520. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs Lamborghini Gallardo LP520 S12 installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
Sources
- Syvecs Lamborghini Gallardo LP520 S12 product listing and application
- Manufacturer kit installation and pinout manual
- Syvecs plug-in kit support index
Manufacturer S12 connector schedule
From pages 9–11 of the Syvecs Gallardo LP520 installation guide, version 1.2. The chart contains the 121 S12 ECU positions and kit notes; it is not a complete vehicle connector schedule. A dash reproduces a blank in the manufacturer table. Verify the kit and loom revision and connector orientation.
| S12 pin | Pin function | SCAL name | Kit connection |
|---|---|---|---|
| 1 | PWRGND | Ecu Ground | Ground |
| 2 | IGN1 | Ignition (20A Open Collector) | Ignition1 |
| 3 | IGN2 | Ignition (20A Open Collector) | Ignition2 |
| 4 | IGN3 | Ignition (20A Open Collector) | Ignition3 |
| 5 | IGN4 | Ignition (20A Open Collector) | Ignition4 |
| 6 | IN25 | — | SPARE 0‐5v Input |
| 7 | KNOCK4 | Knock Sensor 2 | Knock Sensor 2 |
| 8 | KNOCKGND | — | Knock Grounds |
| 9 | THERMO2 + | — | SPARE EGT |
| 10 | IN21 | Thermistor Input | Spare Thermistor Input |
| 11 | IN18 | 5V Analogue Input | Spare 0‐5v Input |
| 12 | IN14 | Configurable Analogue Input | Spare Programmable Input |
| 13 | IN11 | Configurable Analogue Input | Exhaust Cam1 |
| 14 | IN7 | Configurable Analogue Input | Spare Programmable Input |
| 15 | IN4 | Configurable Analogue Input | Map Sensor |
| 16 | IN1 | Configurable Analogue Input | Engine Oil Pressure |
| 17 | LAMI 1 | — | Lam1 ion |
| 18 | CAN LO 2 | — | Spare CanBus |
| 19 | RS232 TX | — | RS232 Transmit |
| 20 | LAN RX‐ | — | Orange/White Cat5 |
| 21 | FUEL 7 | Fuel Injector (10A Open Collector) | Tacho Output |
| 22 | FUEL 3 | Fuel Injector (10A Open Collector) | Injector 3 |
| 23 | VBAT | — | 12v Supply |
| 24 | PWRGND | — | Spare Ground |
| 25 | IN26 | 5V Analogue Input | Spare 0‐5v Input |
| 26 | 5V OUT | 5V OUT | 5v Ref |
| 27 | KNK1 | KNOCK1 | Knock Sensor 1 |
| 28 | THERMO 1 ‐ | THERMO 1 ‐ | Spare EGT |
| 29 | IN22 | Thermistor Input | Spare Thermistor Input |
| 30 | IN19 | 5V Input | Pedal Position 2 |
| 31 | IN15 | Configurable Analogue Input | Cam vvt1 in |
| 32 | IN12 | Configurable Analogue Input | Spare Programmable Input |
| 33 | IN08 | Configurable Analogue Input | A/C Switch |
| 34 | ANGND | SENSOR GROUND | Sensor Ground |
| 35 | IN02 | Configurable Analogue Input | Air Charge Temp |
| 36 | LAMV 1 | — | Lam1V |
| 37 | CAN HI 3 | — | Spare CanBus |
| 38 | RS232 RX | — | Rs232 Receive |
| 39 | LAN RX+ | — | White/Orange Cat5 |
| 40 | FUEL8 | — | VVT1 Intake |
| 41 | FUEL4 | — | Injector 4 |
| 42 | VBAT | — | 12v Supply |
| 43 | PWRGND | — | Ground |
| 44 | IN27 | 5V | Spare 0‐5v Input |
| 45 | 5V OUT | — | 5v Ref |
| 46 | KNOCK2 | — | Knock Sensor2 |
| 47 | THERMO1+ | — | Spare EGT |
| 48 | IN23 | Thermistor Input | Engine Coolant Temp |
| 49 | IN20 | 5V | Pedal Position 1 |
| 50 | IN16 | Configurable Analogue Input | Spare Programmable Input |
| 51 | ANGND | — | Sensor Grounds |
| 52 | IN09 | Configurable Analogue Input | Exhaust Cam 2 |
| 53 | IN05 | Configurable Analogue Input | Crank Sensor |
| 54 | ANGND | — | Sensor Ground |
| 55 | LAMV2 | — | Lam2 V |
| 56 | CAN LO 3 | — | Spare CanBus |
| 57 | COMGND | — | Comms Ground |
| 58 | CAN HI 1 | — | Connected Can Bus |
| 59 | LAN TX‐ | — | Green/White Cat5 |
| 60 | FUEL5 | — | VVT Exhaust 1 |
| 61 | FUEL1 | — | Injector 1 |
| 62 | HBRIDGE5 | — | Spare Half Bridge Output |
| 63 | IN28 | 5V | Spare 0‐5v Input |
| 64 | 10VOUT | — | Configurable sensor voltage output |
| 65 | KNOCK 3 | — | Knock 3 |
| 66 | THEMO 02 ‐ | — | Spare EGT |
| 67 | IN24 | Thermistor Input | Oil Temp |
| 68 | ANGND | — | Sensor Ground |
| 69 | IN17 | 5V | Spare 0‐5v Input |
| 70 | IN13 | — | VVT2 Intake |
| 71 | IN10 | Configurable Analogue Input | Sport Switch |
| 72 | IN6 | Configurable Analogue Input | Brake Pressure |
| 73 | IN3 | Configurable Analogue Input | Spare Programmable Input |
| 74 | LAMI 2 | — | Lam2 I |
| 75 | LamGND | — | Lambda Sensor Grounds |
| 76 | CAN HI 02 | — | Spare Can Bus |
| 77 | CAN LO 1 | — | Connected Can bus |
| 78 | LAN TX+ | — | White/Green Cat5 |
| 79 | FUEL6 | — | Injector 5 |
| 80 | FUEL2 | — | Injector 2 |
| 81 | H BRIDGE 6 | — | Spare Half bridge |
| 82 | H BRIDGE 1 | — | Spare Half Bridge |
| 83 | PWM4 | — | Fuel Pump Relays |
| 84 | PWM8 | — | Rad Fans |
| 85 | FUEL12 | — | Injector 8 |
| 86 | FUEL16 | — | Injector 6 |
| 87 | FUEL20 | — | VVT Ex 2 |
| 88 | FUEL24 | — | VVT Intake 2 |
| 89 | VBAT | — | 12v Supply |
| 90 | H BRIDGE 2 | — | Spare Half Bridge |
| 91 | PWM3 | — | Throttle Relay |
| 92 | PWM7 | — | Main Relay |
| 93 | FUEL11 | — | Injector 7 |
| 94 | FUEL15 | — | Lambda Heaters |
| 95 | FUEL19 | — | Spare Output |
| 96 | FUEL23 | — | Spare Output |
| 97 | PWRGND | — | Ground |
| 98 | H BRIDGE 3 | — | Spare Half Bridge |
| 99 | PWM2 | — | Intake manifold Flap ‐ Ideal for Boost solenoid |
| 100 | PWM6 | — | Oil Pressure Gauge (Pin Write Enable on GFA) |
| 101 | FUEL10 | — | Oil Temp gauge ( Pin Crank waveform on GFA) |
| 102 | FUEL14 | — | Injector 10 |
| 103 | FUEL18 | — | Spare Output |
| 104 | FUEL22 | — | Spare Output |
| 105 | PWRGND | — | Ground |
| 106 | HBRIDGE4 | — | Spare Half Bridge Output |
| 107 | PWM1 | — | Spare Output |
| 108 | PWM5 | — | Spare Output |
| 109 | FUEL9 | — | Spare Output |
| 110 | FUEL13 | — | Injector 9 |
| 111 | FUEL17 | — | Spare Output |
| 112 | FUEL21 | — | Spare Output |
| 113 | PWRGND | — | Ground |
| 114 | IGN5 | — | Ignition 5 |
| 115 | IGN6 | — | Ignition 6 |
| 116 | IGN7 | — | Ignition 7 |
| 117 | IGN8 | — | Ignition 8 |
| 118 | IGN9 | — | Ignition 9 |
| 119 | IGN10 | — | Ignition 10 |
| 120 | IGN11 | — | Ignition 11 |
| 121 | IGN12 | — | Ignition 12 |
Newer kit external 12-way DTM: documented positions
The manual calls this a 12-way connector but lists only the following ten numbered positions. Positions 11 and 12 remain unverified. It separately lists an older lettered 10-way connector; do not treat these as the same revision.
| Pin | Function |
|---|---|
| 1 | AN25 — spare 0–5 V input |
| 2 | AN26 — spare 0–5 V input |
| 3 | AN27 — spare 0–5 V input |
| 4 | +5 V supply |
| 5 | Analogue sensor ground |
| 6 | AN28 — spare 0–5 V input |
| 7 | H-bridge 1 — spare output |
| 8 | H-bridge 2 — spare output |
| 9 | H-bridge 3 — spare output |
| 10 | H-bridge 4 — spare output |