Removed text is struck through; added text is highlighted.
Syvecs S7Plus general-purpose ECU shown as a family reference; vehicle-specific kit and adaptor may differ. Manufacturer photograph, reproduced with permission. Image source.
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Nissan Patrol Y62 2017 onward VK56DD, with product code S7Plus-Nissan-Y62. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs Nissan Patrol Y62 2017 onward VK56DD installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
Sources
Syvecs Nissan Patrol Y62 2017 onward VK56DD product listing and applicationManufacturer kit installation and pinout manualSyvecs plug-in kit support index
Manufacturer ECU-to-loom schedules
From pages 4–6 of the Syvecs Nissan Patrol Y62 kit manual, version 1.0. The source identifies the kit as Y62 without restricting years in the connector chart: confirm the VK56DD application, hardware, connector orientation and loom revision with Syvecs. The table maps the three Syvecs ECU connectors to the manufacturer-listed Patrol loom positions and GDI12 driver where noted; it does not enumerate every factory cavity. A dash represents a blank in the source.
Syvecs pinDescriptionPatrol loom / kit positionManufacturer notesB1PWRGND10Power groundB2EGT2 +17EGT2B3EGT2 −——B4KNOCK15Knock sensor inputB5KNOCK 218Knock 2B6PVBAT120Constant 12 VB7IVBAT14512 V from ECMB8LAM1A792.2B9LAM1B741.8 V variesB10LAM1C——B11LAM1D——B12LAM1HEATER116HeaterB13IVBAT11112 V from ECMB14LAM2A692.2B15LAM2B701.8 V variesB16LAM2C——B17LAM2D——B18LAM2HEATER117HeaterB19IVBAT—CAN bridge 12 VB20KLINE——B21RS232RX / CAN L——B22RS232TX / CAN H——B23LANRX−Orange/white—B24LANRX+White/orange—B25LANTX−Green/white—B26LANTX+White/green—
Connector C
Syvecs pinDescriptionPatrol loom / kit positionManufacturer notesC1KNOCK GROUND20Knock groundC2ANGND13, 42, 43, 44, 45Sensor groundC3ANGND63, 85, 135, 144, 151Cam and crank groundC4ANGND—Sensor groundC55V OUT27, 28, 29, 305 V output for sensorsC65V OUT73, 83, 142, 1465 V output for sensorsC75V OUT—5 V output for sensorsC8CAN L123CAN LC9CAN H124CAN HC10AN0131Cooling fan speedC11AN0241Cam 1 EXC12AN0368Cam 2 EXC13AN0425DI pressureC14AN0533CrankC15AN0640Cam 1C16AN0766Cam 2C17AN08—MAPC18AN0978TPS1AC19AN1080TPS1BC20AN11150PPSAC21AN12143PPSBC22AN1335Coolant temperature inputC23AN1436Air temperature inputC24AN15134Steering wheel switchC25AN1623Engine oil pressureC26CAN3 L137—C27CAN3 H138—C28PWR CTR IN133Ignition switchC29AN S1 / Slave An01Join to C24Steering wheel output buttonsC30AN S2 / Slave An02——C31AN S3 / Slave An0322Engine oil temperatureC32AN S4 / Slave An0461Multiway positionC33AN S5 / Slave An0512A/C pressureC34AN S6 / Slave An06128Fuel temperature
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 2: Syvecs Nissan Patrol Y62 2017 onward VK56DD Plug-in ECUSyvecs S7Plus general-purpose ECU shown as a family reference; vehicle-specific kit and adaptor may differ. Manufacturer photograph, reproduced with permission. Image source.
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Nissan Patrol Y62 2017 onward VK56DD, with product code S7Plus-Nissan-Y62. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs Nissan Patrol Y62 2017 onward VK56DD installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
From pages 4–6 of the Syvecs Nissan Patrol Y62 kit manual, version 1.0. The source identifies the kit as Y62 without restricting years in the connector chart: confirm the VK56DD application, hardware, connector orientation and loom revision with Syvecs. The table maps the three Syvecs ECU connectors to the manufacturer-listed Patrol loom positions and GDI12 driver where noted; it does not enumerate every factory cavity. A dash represents a blank in the source.
Connector A
Syvecs pin
Description
Patrol loom / kit position
Manufacturer notes
A1
PWR CTR OUT
88
Main relay
A2
H-Bridge1 / SlaveOut1
108
DBW+
A3
H-Bridge2 / SlaveOut2
107
DBW−
A4
H-Bridge3 / SlaveOut3
106
Evap PWM
A5
H-Bridge4 / SlaveOut4
90, 93
VVEL trigger and fuel pump relay
A6
H-Bridge5 / SlaveOut5
—
—
A7
H-Bridge6 / SlaveOut6
External
External fan
A8
H-Bridge7 / SlaveOut7
57
Multiway +
A9
H-Bridge8 / SlaveOut8
58
Multiway −
A10
FUEL1
GDI12 pin 13
Cylinder 1 injector
A11
FUEL2
GDI12 pin 22
Cylinder 2 injector
A12
FUEL3
GDI12 pin 23
Cylinder 3 injector
A13
FUEL4
GDI12 pin 19
Cylinder 4 injector
A14
FUEL5
GDI12 pin 29
Cylinder 5 injector
A15
FUEL6
GDI12 pin 14
Cylinder 6 injector
A16
FUEL7
GDI12 pin 30
Cylinder 7 injector
A17
FUEL8
GDI12 pin 17
Cylinder 8 injector
A18
PWM1 / FUEL9
126
Tacho
A19
PWM2 / FUEL10
External
Secondary injector 1
A20
PWM3 / FUEL11
136
Fuel pump computer
A21
PWM4 / FUEL12
External
Secondary injector 2
A22
PWM5 / FUEL13
114
VVTi 1 EX — flyback solder bridge set
A23
PWM6 / FUEL14
115
VVTi 2 EX — flyback solder bridge set
A24
PWM7 / FUEL15
112
VVTi 1 — flyback solder bridge set
A25
PWM8 / FUEL16
113
VVTi 2 — flyback solder bridge set
A26
IGN1
95 & 94
Ignition 1 & 6
A27
IGN2
91 & 92
Ignition 2 & 3
A28
IGN3
104 & 105
Ignition 4 & 7
A29
IGN4
102 & 101
Ignition 5 & 8
A30
IGN5
99
Throttle control relay
A31
IGN6
GDI12 pin 21
DI pump signal
A32
PWRGND
—
—
A33
PWRGND
50
ECU ground
A34
PWRGND
55
ECU ground
Connector B
Syvecs pin
Description
Patrol loom / kit position
Manufacturer notes
B1
PWRGND
10
Power ground
B2
EGT2 +
17
EGT2
B3
EGT2 −
—
—
B4
KNOCK
15
Knock sensor input
B5
KNOCK 2
18
Knock 2
B6
PVBAT
120
Constant 12 V
B7
IVBAT
145
12 V from ECM
B8
LAM1A
79
2.2
B9
LAM1B
74
1.8 V varies
B10
LAM1C
—
—
B11
LAM1D
—
—
B12
LAM1HEATER
116
Heater
B13
IVBAT
111
12 V from ECM
B14
LAM2A
69
2.2
B15
LAM2B
70
1.8 V varies
B16
LAM2C
—
—
B17
LAM2D
—
—
B18
LAM2HEATER
117
Heater
B19
IVBAT
—
CAN bridge 12 V
B20
KLINE
—
—
B21
RS232RX / CAN L
—
—
B22
RS232TX / CAN H
—
—
B23
LANRX−
Orange/white
—
B24
LANRX+
White/orange
—
B25
LANTX−
Green/white
—
B26
LANTX+
White/green
—
Connector C
Syvecs pin
Description
Patrol loom / kit position
Manufacturer notes
C1
KNOCK GROUND
20
Knock ground
C2
ANGND
13, 42, 43, 44, 45
Sensor ground
C3
ANGND
63, 85, 135, 144, 151
Cam and crank ground
C4
ANGND
—
Sensor ground
C5
5V OUT
27, 28, 29, 30
5 V output for sensors
C6
5V OUT
73, 83, 142, 146
5 V output for sensors
C7
5V OUT
—
5 V output for sensors
C8
CAN L
123
CAN L
C9
CAN H
124
CAN H
C10
AN01
31
Cooling fan speed
C11
AN02
41
Cam 1 EX
C12
AN03
68
Cam 2 EX
C13
AN04
25
DI pressure
C14
AN05
33
Crank
C15
AN06
40
Cam 1
C16
AN07
66
Cam 2
C17
AN08
—
MAP
C18
AN09
78
TPS1A
C19
AN10
80
TPS1B
C20
AN11
150
PPSA
C21
AN12
143
PPSB
C22
AN13
35
Coolant temperature input
C23
AN14
36
Air temperature input
C24
AN15
134
Steering wheel switch
C25
AN16
23
Engine oil pressure
C26
CAN3 L
137
—
C27
CAN3 H
138
—
C28
PWR CTR IN
133
Ignition switch
C29
AN S1 / Slave An01
Join to C24
Steering wheel output buttons
C30
AN S2 / Slave An02
—
—
C31
AN S3 / Slave An03
22
Engine oil temperature
C32
AN S4 / Slave An04
61
Multiway position
C33
AN S5 / Slave An05
12
A/C pressure
C34
AN S6 / Slave An06
128
Fuel temperature
Revision 2: Syvecs Nissan Patrol Y62 2017 onward VK56DD Plug-in ECUSyvecs S7Plus general-purpose ECU shown as a family reference; vehicle-specific kit and adaptor may differ. Manufacturer photograph, reproduced with permission. Image source.
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Nissan Patrol Y62 2017 onward VK56DD, with product code S7Plus-Nissan-Y62. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs Nissan Patrol Y62 2017 onward VK56DD installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
From pages 4–6 of the Syvecs Nissan Patrol Y62 kit manual, version 1.0. The source identifies the kit as Y62 without restricting years in the connector chart: confirm the VK56DD application, hardware, connector orientation and loom revision with Syvecs. The table maps the three Syvecs ECU connectors to the manufacturer-listed Patrol loom positions and GDI12 driver where noted; it does not enumerate every factory cavity. A dash represents a blank in the source.