Electromotive TEC-1 is a model in the Total Engine Control family. Early TEC engine-management system covered with TEC-II in Electromotive’s legacy installation and calibration manual. Manufacturer source.
Identification and software
Identify the exact model, serial, firmware and ignition-driver configuration before using a calibration or connecting a loom. WinTEC versions and hardware vary; the Electromotive manual archive separates the generations.
Wiring and pinout
Consult the model-specific manufacturer source and technical archive for the matching connector, firing order, ECU earths, injector drivers and ignition connections. Do not transfer TECgt200 or TECs200 positions to earlier TEC units. Where a complete exact-model pinout has not been verified, use the manufacturer documentation and verify the actual part number.
Availability
As of 17 November 2026, the manufacturer states it is not selling or repairing products. Electromotive notice. See the Electromotive family reference.
Illustrated TEC-I terminal schedules
The printed labels below are taken from the Electromotive's TEC installation manual. They identify the terminals shown in the drawings; they are not manufacturer-numbered connector cavities. Other plugs and wiring vary with the actual ECU, injector drivers and engine. Consult the complete drawing and check the markings on the unit. The TEC-I fuel-pump relay terminal is a ground-switching output; it differs from the TEC-II output described in the manual.
The manual shows different configurations on pages 41–43. The six-cylinder dual-plug drawing and the twelve-cylinder/three-rotor drawings do not show identical terminal-block layouts: the knock and oxygen positions exchange order and the latter drawings include two unlabelled positions. The lists are in drawing order from top to bottom, not pin numbers.
Six-cylinder dual-plug sensor and communication terminals, page 41
| Marking or lead | Documented function |
|---|---|
| CLT | Coolant temperature sensor |
| GND | Ground adjacent to CLT |
| MAT | Manifold air temperature sensor |
| GND | Ground adjacent to MAT |
| KNK | Knock sensor input |
| EGO | Exhaust-gas oxygen sensor signal |
| GND | Ground |
| TXD | Transmit data |
| RXD | Receive data |
Twelve-cylinder and three-rotor sensor and communication terminals, pages 42–43
| Marking or lead | Documented function |
|---|---|
| CLT | Coolant temperature sensor |
| GND | Ground adjacent to CLT |
| MAT | Manifold air temperature sensor |
| GND | Ground adjacent to MAT |
| EGO | Exhaust-gas oxygen sensor signal |
| KNK | Knock sensor input |
| Unlabelled | No assignment given on drawing |
| Unlabelled | No assignment given on drawing |
| GND | Ground |
| TXD | Transmit data |
| RXD | Receive data |
Adjacent output terminals
| Marking or lead | Documented function |
|---|---|
| F.P. RELAY | Fuel-pump relay control; TEC-I uses a pull-to-ground output |
| TACH | Tachometer output |
| CHECK ENG. | Check-engine light output |
| SPARE | Optional general-purpose output; build-dependent |
Illustrated FI injector-driver markings
| Marking or lead | Documented function |
|---|---|
| FI1 | Injector-driver terminal for coil A event; repeated on second driver bank |
| FI2 | Injector-driver terminal for coil B event; repeated on second driver bank |
| FI3 | Injector-driver terminal for coil C event; repeated on second driver bank |
Illustrated power leads
| Marking or lead | Documented function |
|---|---|
| ECU red (+) lead | Positive supply, shown through main-power relay |
| ECU black (−) lead | Ground |
| Direct-fire unit red (+) lead | Positive supply, shown through main-power relay |
| Direct-fire unit black (−) lead | Ground |
The drawing shows an optional second three-driver bank. FI1–FI3 are repeated on the two banks; the manual relates them to the A–C coil events and explains how configurations use the additional drivers. Do not assume that an unlabelled terminal is unused or transplant the later TEC-II numbered header.