Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Tuning
Parent
Bosch LH-Jetronic
Applies to
Bosch LH-Jetronic
Tool groups
None
Manufacturers
Volvo

Selected Volvo redblock engines use Bosch LH 2.4 fuel injection with a separate EZ116K ignition controller. This guide covers sourced examples, not all 200, 700 or 900 models: other years, markets and conversions use different systems. Identify both installed controllers and their software before choosing a calibration.

Fuel and ignition are separate

The workshop description for a 1994 Volvo 940 B230FT identifies LH2.4 multi-point injection working with EZ116K. In a 1991 940 SE B230FT example, the ignition control uses an engine-speed/load map and knock control; if knock persists after timing correction, the documented system can request mixture enrichment. A fuel-controller change therefore does not itself replace a properly matched ignition calibration.

Record engine, turbo hardware, gearbox, market, fuel, each Bosch and Volvo ECU number and the chip/software identity. An ECU label or matching connector does not establish that a binary, ignition module or hardware is interchangeable. Volvo documents EPROM replacement for selected 1991–1993 940s, so identify the installed calibration as well as the outer label. For context on other systems see Volvo ECU identification.

Definitions and calibration research

The TunerPro definition index lists a community XDF for the Volvo 940 B230FT automatic ECU 0 280 000 954, and separately lists a -937 example for the 740 Turbo. It also lists an EZK -208 definition for a B204FT/GT example. These are the index's application claims and separate definitions, not a verified map pack for all LH 2.4 or all EZK units. Match the exact binary and definition, then check map location, axes, units and conversion before relying on a display. XDF availability does not prove a diagnostic datastream or a programming method.

The original LH 2.4 and EZK fuel-and-spark tuning thread was accessible directly when revisited; its author describes separate XDFs and experimental logging. The thread's opening post contains historical corrections: an early 93x main-fuel-table load axis had been inverted, and two 937/950 definitions were later reinterpreted as 12-bit values. This is evidence for checking the exact revision, raw data and axes, not a validated conversion for other files. The author called the 2011 modified-BIN logger alpha and said memory locations were still being investigated. Neither the software nor old attachments were independently tested by this wiki.

For an example of practical research, Post-Haste Performance's 2017 Volvo 740 project says its tuner read an already-modified EPROM, tested third-party definitions and active fuel/ignition tables, then calibrated the modified MAF and injectors and used real-time emulation. This is the tuner's account of one car; the published summary does not establish a transferable binary, map addresses or independently verified result. Community LH 2.4 diagnostic notes are another entry point.

A contributor's later 148-versus-207 EZK comparison reports using different XDFs for those turbo binaries, and notes different EGR configurations. This is a community comparison whose binaries and axes have not been independently verified; the practical point is that opening two files with one definition can compare unrelated bytes. Check the exact ECU, EGR configuration, software and each definition before interpreting differences.

Chip hardware: a chip tuner's FAQ describes EZK units with different daughterboard arrangements and says some need an added board to accept its ignition chips. This is a vendor description, not proof that an arbitrary unit is compatible: identify the installed hardware and software and the actual programming method. Fuel and ignition binaries and definitions are separate. Preserve independently verified original data for the applicable method and establish a recovery path before changing either controller.

Baseline and diagnostic checks

On selected early cars, the community diagnostic notes describe an under-hood test box where socket 2 reads fuel-controller faults and socket 6 reads ignition faults. Later versions may have a different connector; confirm the exact car. Record faults from both systems before clearing and follow the vehicle procedure.

The 1994 B230FT LH2.4 service description identifies a throttle switch and ECU-controlled idle and fuel-cut behaviour. Check the idle/full-load switch, intake leaks, air-mass meter, fuel pressure, lambda feedback and ignition health before attributing poor running to a map. Record boost, RPM and a correctly installed calibrated wideband alongside available ECU data; actual boost and lambda are not interchangeable with the ECU's calculated load or narrowband correction.

Volvo's ignition system manual describes the LH fuel controller sending its air-mass-based load information to the separate ignition controller. Injector or MAF housing changes affect the fuel calculation and can affect the load information exchanged with ignition. Confirm the transfer function, injector flow and opening-time data, operating pressure, knock response and actual mixture across the operating range. The vehicle sources above do not validate a universal injector constant, boost target or file.

Fuel pressure and injector operation

For the 1992 940 B230FT, Volvo specifies fuel line pressure of 300 kPa above intake-manifold pressure. This is an injector pressure differential, not a fixed rail reading relative to atmosphere. Use the same pressure reference at both points: differential = rail gauge pressure − manifold gauge pressure. For illustration, 50 kPa manifold boost with a 300 kPa differential corresponds to about 350 kPa rail gauge; at 50 kPa vacuum it corresponds to about 250 kPa rail gauge. These are arithmetic examples for the documented system, not universal targets. The 1991 940 SE test checks regulator response to reference pressure; use the procedure and equipment appropriate to the actual car.

The 1994 940 B230FT description says all four injectors are pulsed together once per crank revolution in normal operation. For that pattern only, an illustrative commanded duty calculation is pulse width (ms) × rpm / 60000: 8 ms at 3,000 rpm gives 40%. Confirm the pulse pattern and logger calculation for the actual operating mode; this is not a fuel-flow measurement or a universal safe duty limit.

Electrical compatibility is separate from flow calibration. A Volvo conversion-harness guide describes low-impedance turbo injectors used with a ballast resistor pack and high-impedance injectors used with the bypass supplied for that particular harness. Inspect the installed injectors, wiring, ballast and ECU driver requirements; colour or connector fit alone does not establish the correct electrical arrangement, and changing a map cannot fix an incorrect driver load.

Fuel–ignition signals and fallback

Volvo's 940 control-module signal description, which includes B230FT, identifies a digital load signal from the fuel ECU to EZK for ignition advance and a separate knock-enrichment signal in the opposite direction for its listed applicable engines. Signal direction matters when investigating a tune or conversion; follow the correct wiring diagram and diagnostic method for the vehicle rather than treating a static voltage as the complete digital waveform.

In Volvo's 240 B230F LH2.4 manual, a missing air-mass signal selects a preset injection duration as a limp-home function, and closed-throttle overrun can deliberately cut injection. A lean wideband indication on overrun or tolerable running in limp mode does not validate a calibration. These descriptions are for the stated naturally aspirated example; verify fault state and operating conditions on the actual vehicle.

For the Volvo 940 diagnostic descriptions that include B230FT, 2-3-1 concerns long-term correction near its limit in the part-load range, while 2-3-2 concerns correction near its limit at idle. Either can reflect a rich or lean fault; neither identifies a failed oxygen sensor by itself. Possible causes listed across these procedures include air leaks, pressure, injector and sensor faults and exhaust leakage. Record the operating range and follow the correct fault tracing.

In the same series, 3-1-2 is described as a missing ignition-to-fuel knock-enrichment circuit-check signal at startup. Volvo lists a wiring fault and notes that symptoms may normally be absent. It is not, by itself, evidence that the engine is knocking or that the knock sensor has failed.

Throttle-switch confirmation

The same 240 B230F factory manual describes diagnostic control function 2 with the ignition on and the fuel diagnostic socket selected: during its prescribed sequence, flash response 3-3-3 confirms the full-load switch and 3-3-2 confirms the idle switch after throttle movement. These are input-test confirmations, not stored fault codes. Follow the source's exact sequence and the car-specific manual; other models and diagnostic connectors differ. Checking the switch state at both ECUs is useful before interpreting idle, enrichment or overrun behaviour.