Page organisation in this revision
- Page type
- Reference hub
- Subject
- Engine ECU
- Parent
- MicroTech standalone ECUs
- Applies to
- No ECU-specific applicability
- Tool groups
- None
- Manufacturers
- None
Changes from revision 3 to revision 3
Removed text is struck through; added text is highlighted.
MicroTech LT-32c is a standalone or earlier programmable engine-management system. The LT-32c Big Bertha is described with sixteen injector outputs, eight ignition outputs and an integral pressure sensor; configured kit and driver limits need checking. Model-specific information.
Identification and features
Record the ECU label, model, part number, hardware revision, firmware, configured injectors, ignition hardware and loom before comparing systems. Some outputs can be reassigned; hardware, software, current limits and engine-specific options determine what is actually available.
Wiring and pinout
Consult the MicroTech LT-32c wiring and documentation source and identify the exact connector face, part and version. Do not apply wiring from a similarly named model. If an exact drawing is unavailable for the unit at hand, obtain it from the manufacturer or supplier before making connections.
Further information
MicroTech LT-32c model informationWiring, manuals or technical archiveMicroTech manufacturer index
Manufacturer front and rear connector positions
MicroTech's LT-32 auxiliary injector and pin-out drawing, revision 1.0 dated 1 July 2015, is published under its LT-32c wiring diagrams. The drawing itself says LT-32. Confirm the exact hardware revision and loom with MicroTech before applying it. Each table follows the drawing's ECU view, left to right, and identifies relative column position rather than assigning manufacturer's cavity numbers, which the drawing does not provide. Separate crank/cam connectors are shown on the drawing but their complete cavity assignments are not specified here.
Front 20-way plug 2
Relative column from leftUpper row labelLower row label1AUX #3AUX #42INJ AUX #4INPUT #83INJ AUX #4INPUT #74INJ AUX #3INPUT #65INJ AUX #3INPUT #56INJ AUX #2INPUT #47INJ AUX #2INPUT #38INJ AUX #1INPUT #29INJ AUX #1INPUT #110GNDGND
Front 20-way plug 1
Relative column from leftUpper row labelLower row label1AUX #1AUX #22INJ SEC #4IGN OUTPUT T43INJ PRI #4IGN OUTPUT L44INJ SEC #3IGN OUTPUT T35INJ PRI #3IGN OUTPUT L36INJ SEC #2IGN OUTPUT T27INJ PRI #2IGN OUTPUT L28INJ SEC #1IGN OUTPUT T19INJ PRI #1IGN OUTPUT L110GNDGND
Front five-column connector
Relative column from leftUpper row labelLower row label1BATTTACH OUTPUT2IGN +12VFUEL PUMP3GNDAUX INPUT4T.P.S. +5VAIR TEMP5T.P.S. SIGWATER TEMP
Rear eight-column connector
Relative column from leftUpper row labelLower row label10–5V INP #30–5V INP #420–5V INP #10–5V INP #230–5V OXYGND SENSOR4OIL PRESSGND SENSOR5FUEL PRESS+5V SENSOR6SPEED INPUTINPUT #37CAN HI #2CAN LO #28CAN HI #1CAN LO #1
The diagram also shows the MAP sensor connection and separate handset and CAN handset ports. Its CAN setup notes 11-bit CAN 2.0A, 1 Mbit/s, default ID 010 hexadecimal, and an installed 120-ohm termination resistor; confirm configuration for the unit.
Driveshaft speed sensor connections
MicroTech's driveshaft sensor kit guide lists these 32C harness connections for compatible units manufactured from 2018 onward. The guide says earlier units require a software update. This is a sensor wiring table, not a complete ECU pinout.
Sensor wireSensor functionECU harness wireECU functionBlueGroundBlackGroundBrown+5 VBlue+5 V sensor supplyBlackSpeed signalBlue/whiteDriveshaft input
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 3: MicroTech LT-32c
MicroTech LT-32c is a standalone or earlier programmable engine-management system. The LT-32c Big Bertha is described with sixteen injector outputs, eight ignition outputs and an integral pressure sensor; configured kit and driver limits need checking. Model-specific information.
Identification and features
Record the ECU label, model, part number, hardware revision, firmware, configured injectors, ignition hardware and loom before comparing systems. Some outputs can be reassigned; hardware, software, current limits and engine-specific options determine what is actually available.
Wiring and pinout
Consult the MicroTech LT-32c wiring and documentation source and identify the exact connector face, part and version. Do not apply wiring from a similarly named model. If an exact drawing is unavailable for the unit at hand, obtain it from the manufacturer or supplier before making connections.
Further information
Manufacturer front and rear connector positions
MicroTech's LT-32 auxiliary injector and pin-out drawing, revision 1.0 dated 1 July 2015, is published under its LT-32c wiring diagrams. The drawing itself says LT-32. Confirm the exact hardware revision and loom with MicroTech before applying it. Each table follows the drawing's ECU view, left to right, and identifies relative column position rather than assigning manufacturer's cavity numbers, which the drawing does not provide. Separate crank/cam connectors are shown on the drawing but their complete cavity assignments are not specified here.
Front 20-way plug 2
| Relative column from left | Upper row label | Lower row label |
|---|
| 1 | AUX #3 | AUX #4 |
| 2 | INJ AUX #4 | INPUT #8 |
| 3 | INJ AUX #4 | INPUT #7 |
| 4 | INJ AUX #3 | INPUT #6 |
| 5 | INJ AUX #3 | INPUT #5 |
| 6 | INJ AUX #2 | INPUT #4 |
| 7 | INJ AUX #2 | INPUT #3 |
| 8 | INJ AUX #1 | INPUT #2 |
| 9 | INJ AUX #1 | INPUT #1 |
| 10 | GND | GND |
Front 20-way plug 1
| Relative column from left | Upper row label | Lower row label |
|---|
| 1 | AUX #1 | AUX #2 |
| 2 | INJ SEC #4 | IGN OUTPUT T4 |
| 3 | INJ PRI #4 | IGN OUTPUT L4 |
| 4 | INJ SEC #3 | IGN OUTPUT T3 |
| 5 | INJ PRI #3 | IGN OUTPUT L3 |
| 6 | INJ SEC #2 | IGN OUTPUT T2 |
| 7 | INJ PRI #2 | IGN OUTPUT L2 |
| 8 | INJ SEC #1 | IGN OUTPUT T1 |
| 9 | INJ PRI #1 | IGN OUTPUT L1 |
| 10 | GND | GND |
Front five-column connector
| Relative column from left | Upper row label | Lower row label |
|---|
| 1 | BATT | TACH OUTPUT |
| 2 | IGN +12V | FUEL PUMP |
| 3 | GND | AUX INPUT |
| 4 | T.P.S. +5V | AIR TEMP |
| 5 | T.P.S. SIG | WATER TEMP |
Rear eight-column connector
| Relative column from left | Upper row label | Lower row label |
|---|
| 1 | 0–5V INP #3 | 0–5V INP #4 |
| 2 | 0–5V INP #1 | 0–5V INP #2 |
| 3 | 0–5V OXY | GND SENSOR |
| 4 | OIL PRESS | GND SENSOR |
| 5 | FUEL PRESS | +5V SENSOR |
| 6 | SPEED INPUT | INPUT #3 |
| 7 | CAN HI #2 | CAN LO #2 |
| 8 | CAN HI #1 | CAN LO #1 |
The diagram also shows the MAP sensor connection and separate handset and CAN handset ports. Its CAN setup notes 11-bit CAN 2.0A, 1 Mbit/s, default ID 010 hexadecimal, and an installed 120-ohm termination resistor; confirm configuration for the unit.
Driveshaft speed sensor connections
MicroTech's driveshaft sensor kit guide lists these 32C harness connections for compatible units manufactured from 2018 onward. The guide says earlier units require a software update. This is a sensor wiring table, not a complete ECU pinout.
| Sensor wire | Sensor function | ECU harness wire | ECU function |
|---|
| Blue | Ground | Black | Ground |
| Brown | +5 V | Blue | +5 V sensor supply |
| Black | Speed signal | Blue/white | Driveshaft input |
Revision 3: MicroTech LT-32c
MicroTech LT-32c is a standalone or earlier programmable engine-management system. The LT-32c Big Bertha is described with sixteen injector outputs, eight ignition outputs and an integral pressure sensor; configured kit and driver limits need checking. Model-specific information.
Identification and features
Record the ECU label, model, part number, hardware revision, firmware, configured injectors, ignition hardware and loom before comparing systems. Some outputs can be reassigned; hardware, software, current limits and engine-specific options determine what is actually available.
Wiring and pinout
Consult the MicroTech LT-32c wiring and documentation source and identify the exact connector face, part and version. Do not apply wiring from a similarly named model. If an exact drawing is unavailable for the unit at hand, obtain it from the manufacturer or supplier before making connections.
Further information
Manufacturer front and rear connector positions
MicroTech's LT-32 auxiliary injector and pin-out drawing, revision 1.0 dated 1 July 2015, is published under its LT-32c wiring diagrams. The drawing itself says LT-32. Confirm the exact hardware revision and loom with MicroTech before applying it. Each table follows the drawing's ECU view, left to right, and identifies relative column position rather than assigning manufacturer's cavity numbers, which the drawing does not provide. Separate crank/cam connectors are shown on the drawing but their complete cavity assignments are not specified here.
Front 20-way plug 2
| Relative column from left | Upper row label | Lower row label |
|---|
| 1 | AUX #3 | AUX #4 |
| 2 | INJ AUX #4 | INPUT #8 |
| 3 | INJ AUX #4 | INPUT #7 |
| 4 | INJ AUX #3 | INPUT #6 |
| 5 | INJ AUX #3 | INPUT #5 |
| 6 | INJ AUX #2 | INPUT #4 |
| 7 | INJ AUX #2 | INPUT #3 |
| 8 | INJ AUX #1 | INPUT #2 |
| 9 | INJ AUX #1 | INPUT #1 |
| 10 | GND | GND |
Front 20-way plug 1
| Relative column from left | Upper row label | Lower row label |
|---|
| 1 | AUX #1 | AUX #2 |
| 2 | INJ SEC #4 | IGN OUTPUT T4 |
| 3 | INJ PRI #4 | IGN OUTPUT L4 |
| 4 | INJ SEC #3 | IGN OUTPUT T3 |
| 5 | INJ PRI #3 | IGN OUTPUT L3 |
| 6 | INJ SEC #2 | IGN OUTPUT T2 |
| 7 | INJ PRI #2 | IGN OUTPUT L2 |
| 8 | INJ SEC #1 | IGN OUTPUT T1 |
| 9 | INJ PRI #1 | IGN OUTPUT L1 |
| 10 | GND | GND |
Front five-column connector
| Relative column from left | Upper row label | Lower row label |
|---|
| 1 | BATT | TACH OUTPUT |
| 2 | IGN +12V | FUEL PUMP |
| 3 | GND | AUX INPUT |
| 4 | T.P.S. +5V | AIR TEMP |
| 5 | T.P.S. SIG | WATER TEMP |
Rear eight-column connector
| Relative column from left | Upper row label | Lower row label |
|---|
| 1 | 0–5V INP #3 | 0–5V INP #4 |
| 2 | 0–5V INP #1 | 0–5V INP #2 |
| 3 | 0–5V OXY | GND SENSOR |
| 4 | OIL PRESS | GND SENSOR |
| 5 | FUEL PRESS | +5V SENSOR |
| 6 | SPEED INPUT | INPUT #3 |
| 7 | CAN HI #2 | CAN LO #2 |
| 8 | CAN HI #1 | CAN LO #1 |
The diagram also shows the MAP sensor connection and separate handset and CAN handset ports. Its CAN setup notes 11-bit CAN 2.0A, 1 Mbit/s, default ID 010 hexadecimal, and an installed 120-ohm termination resistor; confirm configuration for the unit.
Driveshaft speed sensor connections
MicroTech's driveshaft sensor kit guide lists these 32C harness connections for compatible units manufactured from 2018 onward. The guide says earlier units require a software update. This is a sensor wiring table, not a complete ECU pinout.
| Sensor wire | Sensor function | ECU harness wire | ECU function |
|---|
| Blue | Ground | Black | Ground |
| Brown | +5 V | Blue | +5 V sensor supply |
| Black | Speed signal | Blue/white | Driveshaft input |