Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
MicroTech standalone ECUs
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

MicroTech LT-32c is a standalone or earlier programmable engine-management system. The LT-32c Big Bertha is described with sixteen injector outputs, eight ignition outputs and an integral pressure sensor; configured kit and driver limits need checking. Model-specific information.

Identification and features

Record the ECU label, model, part number, hardware revision, firmware, configured injectors, ignition hardware and loom before comparing systems. Some outputs can be reassigned; hardware, software, current limits and engine-specific options determine what is actually available.

Wiring and pinout

Consult the MicroTech LT-32c wiring and documentation source and identify the exact connector face, part and version. Do not apply wiring from a similarly named model. If an exact drawing is unavailable for the unit at hand, obtain it from the manufacturer or supplier before making connections.

Further information

Manufacturer front and rear connector positions

MicroTech's LT-32 auxiliary injector and pin-out drawing, revision 1.0 dated 1 July 2015, is published under its LT-32c wiring diagrams. The drawing itself says LT-32. Confirm the exact hardware revision and loom with MicroTech before applying it. Each table follows the drawing's ECU view, left to right, and identifies relative column position rather than assigning manufacturer's cavity numbers, which the drawing does not provide. Separate crank/cam connectors are shown on the drawing but their complete cavity assignments are not specified here.

Front 20-way plug 2

Relative column from leftUpper row labelLower row label
1AUX #3AUX #4
2INJ AUX #4INPUT #8
3INJ AUX #4INPUT #7
4INJ AUX #3INPUT #6
5INJ AUX #3INPUT #5
6INJ AUX #2INPUT #4
7INJ AUX #2INPUT #3
8INJ AUX #1INPUT #2
9INJ AUX #1INPUT #1
10GNDGND

Front 20-way plug 1

Relative column from leftUpper row labelLower row label
1AUX #1AUX #2
2INJ SEC #4IGN OUTPUT T4
3INJ PRI #4IGN OUTPUT L4
4INJ SEC #3IGN OUTPUT T3
5INJ PRI #3IGN OUTPUT L3
6INJ SEC #2IGN OUTPUT T2
7INJ PRI #2IGN OUTPUT L2
8INJ SEC #1IGN OUTPUT T1
9INJ PRI #1IGN OUTPUT L1
10GNDGND

Front five-column connector

Relative column from leftUpper row labelLower row label
1BATTTACH OUTPUT
2IGN +12VFUEL PUMP
3GNDAUX INPUT
4T.P.S. +5VAIR TEMP
5T.P.S. SIGWATER TEMP

Rear eight-column connector

Relative column from leftUpper row labelLower row label
10–5V INP #30–5V INP #4
20–5V INP #10–5V INP #2
30–5V OXYGND SENSOR
4OIL PRESSGND SENSOR
5FUEL PRESS+5V SENSOR
6SPEED INPUTINPUT #3
7CAN HI #2CAN LO #2
8CAN HI #1CAN LO #1

The diagram also shows the MAP sensor connection and separate handset and CAN handset ports. Its CAN setup notes 11-bit CAN 2.0A, 1 Mbit/s, default ID 010 hexadecimal, and an installed 120-ohm termination resistor; confirm configuration for the unit.

Driveshaft speed sensor connections

MicroTech's driveshaft sensor kit guide lists these 32C harness connections for compatible units manufactured from 2018 onward. The guide says earlier units require a software update. This is a sensor wiring table, not a complete ECU pinout.

Sensor wireSensor functionECU harness wireECU function
BlueGroundBlackGround
Brown+5 VBlue+5 V sensor supply
BlackSpeed signalBlue/whiteDriveshaft input