Electromotive TEC3 is a model in the Total Engine Control family. TEC3 engine-management system documented in the manufacturer’s installation and calibration manual, version 1.7. Manufacturer source.
Identification and software
Identify the exact model, serial, firmware and ignition-driver configuration before using a calibration or connecting a loom. WinTEC versions and hardware vary; the Electromotive manual archive separates the generations.
Wiring and pinout
Consult the model-specific manufacturer source and technical archive for the matching connector, firing order, ECU earths, injector drivers and ignition connections. Do not transfer TECgt200 or TECs200 positions to earlier TEC units. Where a complete exact-model pinout has not been verified, use the manufacturer documentation and verify the actual part number.
Availability
As of 17 November 2026, the manufacturer states it is not selling or repairing products. Electromotive notice. See the Electromotive family reference.
Manufacturer connector schedules
Electromotive's TEC3 manual version 1.7, pages 165–170, gives different output connectors for the standard TEC3 and the TEC3 6/12. The grey connector is shared between those configurations. W16/W17 are unused on TEC3 6/12, unlike TEC3r. Match the ECU and loom before wiring. Wire colours are the manufacturer harness colours; a slash denotes the stripe. G21 may be white/black on early harnesses. Outputs G1/G2/G20/G21 together and outputs B18–B21 or W18–W21 together each have a combined maximum of 4 A in the manual.
Standard TEC3 black 23-way connector
| Pin | Function | Harness wire |
|---|---|---|
| B1 | Coil channel A | White |
| B2 | Coil channel B | Red |
| B3 | Coil channel C | Black |
| B4 | Coil channel D | Red |
| B5 | Injector channel 1 | Yellow/black |
| B6 | Injector channel 2 | Yellow/red |
| B7 | Injector channel 3 | Yellow/green |
| B8 | Injector channel 4 | Yellow/blue |
| B9 | Injector channel 5 | Light blue/black |
| B10 | Coil wire shield | Bare |
| B11 | Idle air control D | Dark blue/white |
| B12 | Idle air control C | Dark blue/black |
| B13 | Idle air control B | Dark green/white |
| B14 | Idle air control A | Dark green/black |
| B15 | Injector channel 6 | Light blue/red |
| B16 | Unused | — |
| B17 | Unused | — |
| B18 | General-purpose output 1 | White/black |
| B19 | General-purpose output 2 | White/red |
| B20 | General-purpose output 3 | White/green |
| B21 | General-purpose output 4 | White/blue |
| B22 | Injector channel 7 | Light blue/green |
| B23 | Injector channel 8 | Light blue/blue |
TEC3 6/12 white 23-way connector
| Pin | Function | Harness wire |
|---|---|---|
| W1 | Coil channel A1 | White |
| W2 | Coil channel B1 | Red |
| W3 | Coil channel C1 | Black |
| W4 | Coil channel A2 | White |
| W5 | Coil channel B2 | Red |
| W6 | Coil channel C2 | Black |
| W7 | Injector channel 1 | Yellow/black |
| W8 | Injector channel 2 | Yellow/red |
| W9 | Injector channel 3 | Yellow/green |
| W10 | Coil wire shield | Bare |
| W11 | Idle air control D | Dark blue/white |
| W12 | Idle air control C | Dark blue/black |
| W13 | Idle air control B | Dark green/white |
| W14 | Idle air control A | Dark green/black |
| W15 | Injector channel 4 | Yellow/blue |
| W16 | Unused | — |
| W17 | Unused | — |
| W18 | General-purpose output 1 | White/black |
| W19 | General-purpose output 2 | White/red |
| W20 | General-purpose output 3 | White/green |
| W21 | General-purpose output 4 | White/blue |
| W22 | Injector channel 5 | Light blue/black |
| W23 | Injector channel 6 | Light blue/red |
Grey 23-way connector, standard and 6/12
| Pin | Function | Harness wire |
|---|---|---|
| G1 | Tachometer output | Brown |
| G2 | Check-engine light | Pink |
| G3 | +5 V output | Grey/red |
| G4 | Crank/cam ground | Black |
| G5 | Switched +12 V input | Yellow |
| G6 | Oxygen sensor negative | Tan |
| G7 | Oxygen sensor positive | Violet |
| G8 | Knock sensor input | Orange |
| G9 | Crank sensor input | Red, shielded |
| G10 | Cam sensor input | Red, shielded |
| G11 | Crank/cam shield | Bare |
| G12 | Coolant temperature input | Grey |
| G13 | Manifold air temperature input | White |
| G14 | Throttle position input | Dark blue |
| G15 | MAP input | Dark green |
| G16 | General-purpose input 1 | Orange/black |
| G17 | General-purpose input 2 | Orange/red |
| G18 | General-purpose input 3 | Orange/green |
| G19 | General-purpose input 4 | Orange/blue |
| G20 | Fuel pump relay ground | Light green |
| G21 | Datalog status light ground | White/orange |
| G22 | Sensor ground | Black/white |
| G23 | Unused | — |
Two-way ECU power connector
| Position | Function | Harness wire |
|---|---|---|
| A | +12 V input | Red |
| B | Main battery ground | Black |
Standard TEC3 direct-fire-unit harness plugs
| Position | DFU A | DFU B |
|---|---|---|
| A | Coil A | Coil C |
| B | Coil B | Coil D |
| C | Coil C | Unused |
| D | +12 V coil power | +12 V coil power |
TEC3 6/12 direct-fire-unit harness plugs
| Position | DFU A | DFU B |
|---|---|---|
| A | Coil A1 | Coil A2 |
| B | Coil B1 | Coil B2 |
| C | Coil C1 | Coil C2 |
| D | +12 V coil power | +12 V coil power |
DFU position D is supplied by the separately fused coil-power wiring; the original harness diagrams specify 9 A for each DFU.
Serial communication connector
The AiM integration guide identifies these DB9 signal positions; other cavities are not specified in that guide.
DB9 communications
| Pin | Function |
|---|---|
| 2 | ECU RS-232 transmit |
| 3 | ECU RS-232 receive |
| 5 | Signal ground |