Removed text is struck through; added text is highlighted.
Manufacturer product image of WRX104X application ECU: Link ECU. Permission to republish confirmed by the user.
Link G4X WRX104X is a vehicle-specific programmable plug-in ECU for the Subaru WRX 2004 application application listed in Link's model-specific manuals index. It is an application board, rather than the universal wire-in ECU. Check the exact vehicle, market, engine, original ECU and board part number against the manufacturer's WRX104X installation manual.
Identification and installation
Record the Link model label and revision, donor factory ECU connector and car's engine and year. Plug-in boards connect to particular factory-harness layouts; the family or vehicle name alone does not establish every model-year or transmission combination. The manufacturer manual gives the supported application and any installation or configuration notes for this board.
G4X plug-in platforms offer configurable fuel and ignition control but available channels and features depend on the original header and board. The G4X plug-in general specifications are conditional on the particular application and do not mean every input is brought out to the factory harness.
Pinout and tuning
The WRX104X installation manual is the model-specific source for board pinouts, expansion connections, electrical cautions and startup configuration. Use its connector orientation and the exact board version; do not copy a wire-in ECU pinout onto a factory harness. PCLink and manual downloads; Link manufacturer overview.
Manufacturer connector schedules
From Link's WRX10X installation manual. Link describes the pinout view as looking into the ECU from the wire side. A dash reproduces an unspecified source field; nc is Link's label. Confirm the vehicle, market and board revision before use.
This is the 2004–2006 schedule from the shared WRXLink (04)/(07) guide. Do not substitute it for the other generation’s header.
Factory main header
Factory pinLink ECU channelFactory functionA1DI 4Clutch SwitchC3Injector 4InjectionA2nc—C4Injector 3InjectionA3nc—C5Injector 2InjectionA4nc—C6Injector 1InjectionA5nc—C7DI10Cruise MainA6Ground—C8nc (Brake NO)—A7nc—C9DI 5Brake Switch (NC)A8Aux 8Tumble Valves CloseC10DI 6Cruise Cancel OR ResumeA9Linked to A10TGV wired in seriesC11DI 7Cruise Set OR CancelA10Linked to A9—C12An Temp 3Fuel TemperatureA11Aux 7Tumble Valves OpenC13An Temp 2IAT from MAFA12nc—C14An Temp 1ECTA13nc—C15+5V Out—A14Injector 5 (Aux)Purge SolenoidC16+5V Out—A15Injector 6 (Aux)Cruise LightC17An Volt 10APS (Main)A16nc (Cruise Set Light)—C18An Volt 2TPS (Main)A17Injector 8 (Aux)CE LightC19nc—A18+14V OutAVCS SolenoidC20nc—A19+14V OutAVCS SolenoidC21nc—A20nc—C22An Volt 1MAPA21nc—C23An Volt 8MAF SignalA22nc—C24nc—A23Aux 3TachoC25Knock 1KnockA24nc—C26An Volt 4Left TGV PositionA25Ground—C27An Volt 5Right TGV PositionA26nc—C28An Volt 9APS (Sub)A27nc—C29An Volt 3TPS (Sub)A28Aux 2Bank 1 (RH) AVCS SolenoidC30nc—A29Aux 1Bank 2 (LH) AVCS SolenoidC31Ground (AFM)—A30nc—C32Ground (AFM Shield)—A31nc—C33Ground (Knock Shield)—A32Aux 5Wastegate SolenoidC34Ground (APS)—A33nc—C35Ground (Signal)—A34Ground (Signal)—D1Ground (Signal)—B1Ground—D2Ground (Signal)—B2Injector 7 (Aux)Rear Oxy HeaterD3Ground—B3nc—D4Aux 9EThrottle Motor +B4Ground—D5Aux 10EThrottle Motor -B5+14V Main RelayECU PowerD6+14V EThrottleFrom EThrottle RelayB6+14V Main RelayECU PowerD7Ground—B7nc—D8DI 8Start SignalB8Trig 2Bank 2 (LH) Cam PositionD9DI 9Neutral SignalB9DI 2Bank 1 (RH) Cam PositionD10An Volt 6Power Steer SwitchB10Trig 1Trig 1 (Crank)D11nc—B11nc—D12nc—B12Ground—D13nc—B13nc—D14Ignition Switch (05- 06)Controls Main Relay (05-06)B14nc—D15Ignition Switch (04)Controls Main Relay (04)B15Ignition 4IgnitionD16DI3 (04) / Main Relay (05-06)AC Request (04) / Ground when on (05-06)B16Ignition 3IgnitionD17Main Relay (04) / DI3 (05-06)Ground when on (04) / AC Request (05-06)B17Ignition 2IgnitionD18nc—B18Ignition 1IgnitionD19nc—B19nc—D20nc—B20nc—D21nc—B21nc—D22nc—B22Ground (Cams)—D23nc—B23nc—D24nc—B24Ignition 5 (Aux)AC FanD25An Volt 7Rear Oxy SignalB25Ignition 7 (Aux)Engine FanD26nc—B26Aux 6 (04) / DI 1 (05-06)FP Speed (04) / Vehicle Speed (05-06)D27nc—B27DI 1 (04) / Aux 6 (05-06)Vehicle Speed (04) / FP Speed (05-06)D28nc—B28nc—D29nc—B29nc—D30nc—B30nc—D31Ground (Shield)—B31Ground (Crank Shield)—B32nc—B33Ignition 6 (Aux)AC RelayB34nc—B35Ignition 8 (Aux)E-Throttle RelayC1nc—C2nc—
Expansion connector
PositionLink ECU channelFunctionExpansion 1Ground (Signal)—Expansion 2+5V Out—Expansion 3nc—Expansion 4nc—Expansion 5An Volt 12—Expansion 6nc—Expansion 7An Temp 4—Expansion 8An Volt 11—
Open each version to inspect formatting, tables and photographs.
Revision 3: Link G4X WRX104X plug-in ECUManufacturer product image of WRX104X application ECU: Link ECU. Permission to republish confirmed by the user.
Link G4X WRX104X is a vehicle-specific programmable plug-in ECU for the Subaru WRX 2004 application application listed in Link's model-specific manuals index. It is an application board, rather than the universal wire-in ECU. Check the exact vehicle, market, engine, original ECU and board part number against the manufacturer's WRX104X installation manual.
Identification and installation
Record the Link model label and revision, donor factory ECU connector and car's engine and year. Plug-in boards connect to particular factory-harness layouts; the family or vehicle name alone does not establish every model-year or transmission combination. The manufacturer manual gives the supported application and any installation or configuration notes for this board.
G4X plug-in platforms offer configurable fuel and ignition control but available channels and features depend on the original header and board. The G4X plug-in general specifications are conditional on the particular application and do not mean every input is brought out to the factory harness.
Pinout and tuning
The WRX104X installation manual is the model-specific source for board pinouts, expansion connections, electrical cautions and startup configuration. Use its connector orientation and the exact board version; do not copy a wire-in ECU pinout onto a factory harness. PCLink and manual downloads; Link manufacturer overview.
Manufacturer connector schedules
From Link's WRX10X installation manual. Link describes the pinout view as looking into the ECU from the wire side. A dash reproduces an unspecified source field; nc is Link's label. Confirm the vehicle, market and board revision before use.
This is the 2004–2006 schedule from the shared WRXLink (04)/(07) guide. Do not substitute it for the other generation’s header.
Factory main header
Factory pin
Link ECU channel
Factory function
A1
DI 4
Clutch Switch
C3
Injector 4
Injection
A2
nc
—
C4
Injector 3
Injection
A3
nc
—
C5
Injector 2
Injection
A4
nc
—
C6
Injector 1
Injection
A5
nc
—
C7
DI10
Cruise Main
A6
Ground
—
C8
nc (Brake NO)
—
A7
nc
—
C9
DI 5
Brake Switch (NC)
A8
Aux 8
Tumble Valves Close
C10
DI 6
Cruise Cancel OR Resume
A9
Linked to A10
TGV wired in series
C11
DI 7
Cruise Set OR Cancel
A10
Linked to A9
—
C12
An Temp 3
Fuel Temperature
A11
Aux 7
Tumble Valves Open
C13
An Temp 2
IAT from MAF
A12
nc
—
C14
An Temp 1
ECT
A13
nc
—
C15
+5V Out
—
A14
Injector 5 (Aux)
Purge Solenoid
C16
+5V Out
—
A15
Injector 6 (Aux)
Cruise Light
C17
An Volt 10
APS (Main)
A16
nc (Cruise Set Light)
—
C18
An Volt 2
TPS (Main)
A17
Injector 8 (Aux)
CE Light
C19
nc
—
A18
+14V Out
AVCS Solenoid
C20
nc
—
A19
+14V Out
AVCS Solenoid
C21
nc
—
A20
nc
—
C22
An Volt 1
MAP
A21
nc
—
C23
An Volt 8
MAF Signal
A22
nc
—
C24
nc
—
A23
Aux 3
Tacho
C25
Knock 1
Knock
A24
nc
—
C26
An Volt 4
Left TGV Position
A25
Ground
—
C27
An Volt 5
Right TGV Position
A26
nc
—
C28
An Volt 9
APS (Sub)
A27
nc
—
C29
An Volt 3
TPS (Sub)
A28
Aux 2
Bank 1 (RH) AVCS Solenoid
C30
nc
—
A29
Aux 1
Bank 2 (LH) AVCS Solenoid
C31
Ground (AFM)
—
A30
nc
—
C32
Ground (AFM Shield)
—
A31
nc
—
C33
Ground (Knock Shield)
—
A32
Aux 5
Wastegate Solenoid
C34
Ground (APS)
—
A33
nc
—
C35
Ground (Signal)
—
A34
Ground (Signal)
—
D1
Ground (Signal)
—
B1
Ground
—
D2
Ground (Signal)
—
B2
Injector 7 (Aux)
Rear Oxy Heater
D3
Ground
—
B3
nc
—
D4
Aux 9
EThrottle Motor +
B4
Ground
—
D5
Aux 10
EThrottle Motor -
B5
+14V Main Relay
ECU Power
D6
+14V EThrottle
From EThrottle Relay
B6
+14V Main Relay
ECU Power
D7
Ground
—
B7
nc
—
D8
DI 8
Start Signal
B8
Trig 2
Bank 2 (LH) Cam Position
D9
DI 9
Neutral Signal
B9
DI 2
Bank 1 (RH) Cam Position
D10
An Volt 6
Power Steer Switch
B10
Trig 1
Trig 1 (Crank)
D11
nc
—
B11
nc
—
D12
nc
—
B12
Ground
—
D13
nc
—
B13
nc
—
D14
Ignition Switch (05- 06)
Controls Main Relay (05-06)
B14
nc
—
D15
Ignition Switch (04)
Controls Main Relay (04)
B15
Ignition 4
Ignition
D16
DI3 (04) / Main Relay (05-06)
AC Request (04) / Ground when on (05-06)
B16
Ignition 3
Ignition
D17
Main Relay (04) / DI3 (05-06)
Ground when on (04) / AC Request (05-06)
B17
Ignition 2
Ignition
D18
nc
—
B18
Ignition 1
Ignition
D19
nc
—
B19
nc
—
D20
nc
—
B20
nc
—
D21
nc
—
B21
nc
—
D22
nc
—
B22
Ground (Cams)
—
D23
nc
—
B23
nc
—
D24
nc
—
B24
Ignition 5 (Aux)
AC Fan
D25
An Volt 7
Rear Oxy Signal
B25
Ignition 7 (Aux)
Engine Fan
D26
nc
—
B26
Aux 6 (04) / DI 1 (05-06)
FP Speed (04) / Vehicle Speed (05-06)
D27
nc
—
B27
DI 1 (04) / Aux 6 (05-06)
Vehicle Speed (04) / FP Speed (05-06)
D28
nc
—
B28
nc
—
D29
nc
—
B29
nc
—
D30
nc
—
B30
nc
—
D31
Ground (Shield)
—
B31
Ground (Crank Shield)
—
B32
nc
—
B33
Ignition 6 (Aux)
AC Relay
B34
nc
—
B35
Ignition 8 (Aux)
E-Throttle Relay
C1
nc
—
C2
nc
—
Expansion connector
Position
Link ECU channel
Function
Expansion 1
Ground (Signal)
—
Expansion 2
+5V Out
—
Expansion 3
nc
—
Expansion 4
nc
—
Expansion 5
An Volt 12
—
Expansion 6
nc
—
Expansion 7
An Temp 4
—
Expansion 8
An Volt 11
—
CAN 1/RS232 Connector
Pin
Function
Wire colour
1
Comms GND
Brown
2
CAN1 L
Green
3
CAN1 H
White
4
RS232-RX
Grey
5
RS232-TX
Yellow
CAN 2/OBD Connector
Pin
Function
Wire colour
1
GND
Brown
2
CAN2 L
Green
3
CAN2 H
White
4
NC
Grey
5
+14V
Yellow
Revision 3: Link G4X WRX104X plug-in ECUManufacturer product image of WRX104X application ECU: Link ECU. Permission to republish confirmed by the user.
Link G4X WRX104X is a vehicle-specific programmable plug-in ECU for the Subaru WRX 2004 application application listed in Link's model-specific manuals index. It is an application board, rather than the universal wire-in ECU. Check the exact vehicle, market, engine, original ECU and board part number against the manufacturer's WRX104X installation manual.
Identification and installation
Record the Link model label and revision, donor factory ECU connector and car's engine and year. Plug-in boards connect to particular factory-harness layouts; the family or vehicle name alone does not establish every model-year or transmission combination. The manufacturer manual gives the supported application and any installation or configuration notes for this board.
G4X plug-in platforms offer configurable fuel and ignition control but available channels and features depend on the original header and board. The G4X plug-in general specifications are conditional on the particular application and do not mean every input is brought out to the factory harness.
Pinout and tuning
The WRX104X installation manual is the model-specific source for board pinouts, expansion connections, electrical cautions and startup configuration. Use its connector orientation and the exact board version; do not copy a wire-in ECU pinout onto a factory harness. PCLink and manual downloads; Link manufacturer overview.
Manufacturer connector schedules
From Link's WRX10X installation manual. Link describes the pinout view as looking into the ECU from the wire side. A dash reproduces an unspecified source field; nc is Link's label. Confirm the vehicle, market and board revision before use.
This is the 2004–2006 schedule from the shared WRXLink (04)/(07) guide. Do not substitute it for the other generation’s header.