Removed text is struck through; added text is highlighted.
Vi-PEC iSupra i-Series plug-in ECU shown as a family illustration; this V-Series model's board, enclosure and vehicle connectors differ. Image: Link Engine Management Vi-PEC product archive, reproduced with permission.
Vi-PEC V Series Nissan 300ZX is a V Series plug-in ECU documented for Nissan 300ZX Z32. It is a vehicle-specific replacement board, and the precise model year, engine, ECU connector and market variant must be checked against the installation guide. Link's Vi-PEC manual index.
Installation and pin functions
Use the specific Vi-PEC installation manual for this application. Its installation instructions and pin-function sections identify connections and application differences; a similarly named V Series plug-in board for another vehicle must not be used as a wiring reference. Check the original ECU part number and wiring before fitting.
Programming and support
Link lists Vi-PEC Tuning Software (VTS) for the V Series. Firmware compatibility and the calibration depend on the ECU version. Consult the software archive and retain the original calibration before any change.
Identification limits
This page is indexed by the documented application rather than an independently verified manufacturer SKU. Check the manual for exact compatibility and do not infer additional vehicle fitments.
Manufacturer pinout tables
All positions listed in the application-specific Vi-PEC installation guide, page 20, appear below. The guide specifies the view looking into the ECU from the wire side. It does not list all factory connector cavities; omitted positions are not assumed unused. The guide identifies the Nissan 300ZX Z32. It lists Aux–Inj 8 at both pins 6 and 19; verify the loom and configured output.
PositionECU functionInternal MAPAn Volt 1Expansion 1Signal GroundExpansion 2+5V OutExpansion 3DI 5Expansion 4DI 6Expansion 5An Volt 8Expansion 6An Volt 7Expansion 7An Temp 3Expansion 8An Temp 4
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 3: Vi-PEC V Series Nissan 300ZXVi-PEC iSupra i-Series plug-in ECU shown as a family illustration; this V-Series model's board, enclosure and vehicle connectors differ. Image: Link Engine Management Vi-PEC product archive, reproduced with permission.
Vi-PEC V Series Nissan 300ZX is a V Series plug-in ECU documented for Nissan 300ZX Z32. It is a vehicle-specific replacement board, and the precise model year, engine, ECU connector and market variant must be checked against the installation guide. Link's Vi-PEC manual index.
Installation and pin functions
Use the specific Vi-PEC installation manual for this application. Its installation instructions and pin-function sections identify connections and application differences; a similarly named V Series plug-in board for another vehicle must not be used as a wiring reference. Check the original ECU part number and wiring before fitting.
Programming and support
Link lists Vi-PEC Tuning Software (VTS) for the V Series. Firmware compatibility and the calibration depend on the ECU version. Consult the software archive and retain the original calibration before any change.
Identification limits
This page is indexed by the documented application rather than an independently verified manufacturer SKU. Check the manual for exact compatibility and do not infer additional vehicle fitments.
Manufacturer pinout tables
All positions listed in the application-specific Vi-PEC installation guide, page 20, appear below. The guide specifies the view looking into the ECU from the wire side. It does not list all factory connector cavities; omitted positions are not assumed unused. The guide identifies the Nissan 300ZX Z32. It lists Aux–Inj 8 at both pins 6 and 19; verify the loom and configured output.
Main ECU connector: documented positions
Position
ECU function
101
Injector 1
29
An Volt 6
103
Injector 3
32
Aux 7
104
Aux 2
34
An Volt 5
105
Injector 5
35
Aux 5
110
Injector 2
36
An Temp 2
112
Injector 4
38
An Volt 3
113
Aux 8
41
Trig 2
114
Injector 6
42
Trig 1
116
Ground
43
DI 2
44
DI 4
1
Ignition 1
45
+12V Key On
2
Ignition 2
46
DI 1
3
Ignition 3
48 & 57
+ 5V Out
4
Aux – Inj 7
49 & 59
+14V
6
Aux – Inj 8
53
DI 3
7
Aux 4
55
An Volt 4
9
Aux 3
11
Ignition 4
12
Ignition 5
13
Ignition 6
18
Aux 6
19
Aux - Inj 8
23
Knock 1
25
Aux 1
27
An Volt 2
28
An Temp 1
Other connections
Position
ECU function
Internal MAP
An Volt 1
Expansion 1
Signal Ground
Expansion 2
+5V Out
Expansion 3
DI 5
Expansion 4
DI 6
Expansion 5
An Volt 8
Expansion 6
An Volt 7
Expansion 7
An Temp 3
Expansion 8
An Temp 4
Revision 3: Vi-PEC V Series Nissan 300ZXVi-PEC iSupra i-Series plug-in ECU shown as a family illustration; this V-Series model's board, enclosure and vehicle connectors differ. Image: Link Engine Management Vi-PEC product archive, reproduced with permission.
Vi-PEC V Series Nissan 300ZX is a V Series plug-in ECU documented for Nissan 300ZX Z32. It is a vehicle-specific replacement board, and the precise model year, engine, ECU connector and market variant must be checked against the installation guide. Link's Vi-PEC manual index.
Installation and pin functions
Use the specific Vi-PEC installation manual for this application. Its installation instructions and pin-function sections identify connections and application differences; a similarly named V Series plug-in board for another vehicle must not be used as a wiring reference. Check the original ECU part number and wiring before fitting.
Programming and support
Link lists Vi-PEC Tuning Software (VTS) for the V Series. Firmware compatibility and the calibration depend on the ECU version. Consult the software archive and retain the original calibration before any change.
Identification limits
This page is indexed by the documented application rather than an independently verified manufacturer SKU. Check the manual for exact compatibility and do not infer additional vehicle fitments.
Manufacturer pinout tables
All positions listed in the application-specific Vi-PEC installation guide, page 20, appear below. The guide specifies the view looking into the ECU from the wire side. It does not list all factory connector cavities; omitted positions are not assumed unused. The guide identifies the Nissan 300ZX Z32. It lists Aux–Inj 8 at both pins 6 and 19; verify the loom and configured output.