Removed text is struck through; added text is highlighted.
Vi-PEC iSupra i-Series plug-in ECU shown as a family illustration; this V-Series model's board, enclosure and vehicle connectors differ. Image: Link Engine Management Vi-PEC product archive, reproduced with permission.
Vi-PEC V Series Mitsubishi Galant VR4 is a V Series plug-in ECU documented for Mitsubishi Galant VR4 4G63 and Eagle Talon as identified by Link. It is a vehicle-specific replacement board, and the precise model year, engine, ECU connector and market variant must be checked against the installation guide. Link's Vi-PEC manual index.
Installation and pin functions
Use the specific Vi-PEC installation manual for this application. Its installation instructions and pin-function sections identify connections and application differences; a similarly named V Series plug-in board for another vehicle must not be used as a wiring reference. Check the original ECU part number and wiring before fitting.
Programming and support
Link lists Vi-PEC Tuning Software (VTS) for the V Series. Firmware compatibility and the calibration depend on the ECU version. Consult the software archive and retain the original calibration before any change.
Identification limits
This page is indexed by the documented application rather than an independently verified manufacturer SKU. Check the manual for exact compatibility and do not infer additional vehicle fitments.
Manufacturer pinout tables
All positions listed in the application-specific Vi-PEC installation guide, page 20, are shown below. The drawing uses a view looking into the ECU from the wire side. Positions omitted by the source are not assumed unused; configure the channels for the vehicle. The manufacturer labels this as the Galant VR4 Gen 6 application. Confirm the vehicle and loom before fitting.
PositionECU functionExpansion 1Signal GroundExpansion 2+5V OutExpansion 3N/CExpansion 4DI 6Expansion 5An Volt 5Expansion 6An Volt 6Expansion 7N/CExpansion 8An Temp 3On Board MapAn Volt 3
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 3: Vi-PEC V Series Mitsubishi Galant VR4Vi-PEC iSupra i-Series plug-in ECU shown as a family illustration; this V-Series model's board, enclosure and vehicle connectors differ. Image: Link Engine Management Vi-PEC product archive, reproduced with permission.
Vi-PEC V Series Mitsubishi Galant VR4 is a V Series plug-in ECU documented for Mitsubishi Galant VR4 4G63 and Eagle Talon as identified by Link. It is a vehicle-specific replacement board, and the precise model year, engine, ECU connector and market variant must be checked against the installation guide. Link's Vi-PEC manual index.
Installation and pin functions
Use the specific Vi-PEC installation manual for this application. Its installation instructions and pin-function sections identify connections and application differences; a similarly named V Series plug-in board for another vehicle must not be used as a wiring reference. Check the original ECU part number and wiring before fitting.
Programming and support
Link lists Vi-PEC Tuning Software (VTS) for the V Series. Firmware compatibility and the calibration depend on the ECU version. Consult the software archive and retain the original calibration before any change.
Identification limits
This page is indexed by the documented application rather than an independently verified manufacturer SKU. Check the manual for exact compatibility and do not infer additional vehicle fitments.
Manufacturer pinout tables
All positions listed in the application-specific Vi-PEC installation guide, page 20, are shown below. The drawing uses a view looking into the ECU from the wire side. Positions omitted by the source are not assumed unused; configure the channels for the vehicle. The manufacturer labels this as the Galant VR4 Gen 6 application. Confirm the vehicle and loom before fitting.
Main ECU connector: documented positions
Position
ECU function
4
An Volt 4
67
Aux 5
5
DI 2
68
Aux 6
7
DI 4
105
Aux 1
8
An Temp 1
108
DI 1
10
An Volt 2
102
+14V Main Relay
18
DI 3
101
Ground
19
An Volt 1
20
An Temp 2
21
Trig 1
22
Trig 2
51
Injector 1
52
Injector 2
53
Aux 2
54
Ignition 1/4
55
Ignition 2/3
56
Aux – Ign 3
57
Aux – Ign 4
58
Aux 8
59
Aux 7
60
Injector 3
61
Injector 4
62
Aux – Inj 5
64
Aux 3
65
Aux 4
Other connections
Position
ECU function
Expansion 1
Signal Ground
Expansion 2
+5V Out
Expansion 3
N/C
Expansion 4
DI 6
Expansion 5
An Volt 5
Expansion 6
An Volt 6
Expansion 7
N/C
Expansion 8
An Temp 3
On Board Map
An Volt 3
Revision 3: Vi-PEC V Series Mitsubishi Galant VR4Vi-PEC iSupra i-Series plug-in ECU shown as a family illustration; this V-Series model's board, enclosure and vehicle connectors differ. Image: Link Engine Management Vi-PEC product archive, reproduced with permission.
Vi-PEC V Series Mitsubishi Galant VR4 is a V Series plug-in ECU documented for Mitsubishi Galant VR4 4G63 and Eagle Talon as identified by Link. It is a vehicle-specific replacement board, and the precise model year, engine, ECU connector and market variant must be checked against the installation guide. Link's Vi-PEC manual index.
Installation and pin functions
Use the specific Vi-PEC installation manual for this application. Its installation instructions and pin-function sections identify connections and application differences; a similarly named V Series plug-in board for another vehicle must not be used as a wiring reference. Check the original ECU part number and wiring before fitting.
Programming and support
Link lists Vi-PEC Tuning Software (VTS) for the V Series. Firmware compatibility and the calibration depend on the ECU version. Consult the software archive and retain the original calibration before any change.
Identification limits
This page is indexed by the documented application rather than an independently verified manufacturer SKU. Check the manual for exact compatibility and do not infer additional vehicle fitments.
Manufacturer pinout tables
All positions listed in the application-specific Vi-PEC installation guide, page 20, are shown below. The drawing uses a view looking into the ECU from the wire side. Positions omitted by the source are not assumed unused; configure the channels for the vehicle. The manufacturer labels this as the Galant VR4 Gen 6 application. Confirm the vehicle and loom before fitting.