Removed text is struck through; added text is highlighted.
Vi-PEC iSupra i-Series plug-in ECU shown as a family illustration; this V-Series model's board, enclosure and vehicle connectors differ. Image: Link Engine Management Vi-PEC product archive, reproduced with permission.
Vi-PEC V Series Honda Civic 1992-1995 is a V Series plug-in ECU documented for Honda Civic 1992–1995 OBD1 as identified by the Link manual index. It is a vehicle-specific replacement board, and the precise model year, engine, ECU connector and market variant must be checked against the installation guide. Link's Vi-PEC manual index.
Installation and pin functions
Use the specific Vi-PEC installation manual for this application. Its installation instructions and pin-function sections identify connections and application differences; a similarly named V Series plug-in board for another vehicle must not be used as a wiring reference. Check the original ECU part number and wiring before fitting.
Programming and support
Link lists Vi-PEC Tuning Software (VTS) for the V Series. Firmware compatibility and the calibration depend on the ECU version. Consult the software archive and retain the original calibration before any change.
Identification limits
This page is indexed by the documented application rather than an independently verified manufacturer SKU. Check the manual for exact compatibility and do not infer additional vehicle fitments.
Manufacturer pinout tables
All positions listed in the application-specific Vi-PEC installation guide, page 20, appear below. The guide specifies the view looking into the ECU from the wire side. It does not list every factory connector cavity; omitted positions are not assumed unused. The source lists Aux–Inj 6 at both A-7 and A-8, and Ignition 2 at both A-18 and A-22. Confirm the loom and output use.
PositionECU functionExpansion 1Signal GroundExpansion 2+5V OutExpansion 3Aux 8Expansion 4DI 6Expansion 5An Volt 4Expansion 6An Volt 5Expansion 7An Volt 6Expansion 8An Temp 3
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 3: Vi-PEC V Series Honda Civic 1992-1995Vi-PEC iSupra i-Series plug-in ECU shown as a family illustration; this V-Series model's board, enclosure and vehicle connectors differ. Image: Link Engine Management Vi-PEC product archive, reproduced with permission.
Vi-PEC V Series Honda Civic 1992-1995 is a V Series plug-in ECU documented for Honda Civic 1992–1995 OBD1 as identified by the Link manual index. It is a vehicle-specific replacement board, and the precise model year, engine, ECU connector and market variant must be checked against the installation guide. Link's Vi-PEC manual index.
Installation and pin functions
Use the specific Vi-PEC installation manual for this application. Its installation instructions and pin-function sections identify connections and application differences; a similarly named V Series plug-in board for another vehicle must not be used as a wiring reference. Check the original ECU part number and wiring before fitting.
Programming and support
Link lists Vi-PEC Tuning Software (VTS) for the V Series. Firmware compatibility and the calibration depend on the ECU version. Consult the software archive and retain the original calibration before any change.
Identification limits
This page is indexed by the documented application rather than an independently verified manufacturer SKU. Check the manual for exact compatibility and do not infer additional vehicle fitments.
Manufacturer pinout tables
All positions listed in the application-specific Vi-PEC installation guide, page 20, appear below. The guide specifies the view looking into the ECU from the wire side. It does not list every factory connector cavity; omitted positions are not assumed unused. The source lists Aux–Inj 6 at both A-7 and A-8, and Ignition 2 at both A-18 and A-22. Confirm the loom and output use.
Main ECU connector: documented positions
Position
ECU function
A-1
Injection 1
D-13
An Temp 1
A-2
Injection 4
D-14
An Volt 2
A-3
Injection 2
D-15
An Temp 2
A-4
Aux 5
D-17
An Volt 3
A-5
Injection 3
B-2
Ground
A-6
Aux – Inj 5
B-1
+14V Main Relay
A-7
Aux – Inj 6
A-8
Aux – Inj 6
A-9
Aux 1
A-10
Ignition 4
A-12
Aux 7
A-13
Aux 2
A-14
Ignition 3
A-15
Aux 3
A-17
Aux 6
A-18
Ignition 2
A-21
Ignition 1
A-22
Ignition 2
B-5
DI 5
B-7
DI 1
B-8
DI 2
B-9
DI 3
B-10
DI 4
D-11
An Volt 1
Other connections
Position
ECU function
Expansion 1
Signal Ground
Expansion 2
+5V Out
Expansion 3
Aux 8
Expansion 4
DI 6
Expansion 5
An Volt 4
Expansion 6
An Volt 5
Expansion 7
An Volt 6
Expansion 8
An Temp 3
Revision 3: Vi-PEC V Series Honda Civic 1992-1995Vi-PEC iSupra i-Series plug-in ECU shown as a family illustration; this V-Series model's board, enclosure and vehicle connectors differ. Image: Link Engine Management Vi-PEC product archive, reproduced with permission.
Vi-PEC V Series Honda Civic 1992-1995 is a V Series plug-in ECU documented for Honda Civic 1992–1995 OBD1 as identified by the Link manual index. It is a vehicle-specific replacement board, and the precise model year, engine, ECU connector and market variant must be checked against the installation guide. Link's Vi-PEC manual index.
Installation and pin functions
Use the specific Vi-PEC installation manual for this application. Its installation instructions and pin-function sections identify connections and application differences; a similarly named V Series plug-in board for another vehicle must not be used as a wiring reference. Check the original ECU part number and wiring before fitting.
Programming and support
Link lists Vi-PEC Tuning Software (VTS) for the V Series. Firmware compatibility and the calibration depend on the ECU version. Consult the software archive and retain the original calibration before any change.
Identification limits
This page is indexed by the documented application rather than an independently verified manufacturer SKU. Check the manual for exact compatibility and do not infer additional vehicle fitments.
Manufacturer pinout tables
All positions listed in the application-specific Vi-PEC installation guide, page 20, appear below. The guide specifies the view looking into the ECU from the wire side. It does not list every factory connector cavity; omitted positions are not assumed unused. The source lists Aux–Inj 6 at both A-7 and A-8, and Ignition 2 at both A-18 and A-22. Confirm the loom and output use.