Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
Link standalone ECUs
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Changes from revision 3 to revision 3

Removed text is struck through; added text is highlighted.

Manufacturer product image of HC20X application ECU: Link ECU. Permission to republish confirmed by the user.

Link G4X HC20X is a vehicle-specific programmable plug-in ECU for the Honda K20 / DC5 application listed in Link's model-specific manuals index. It is an application board, rather than the universal wire-in ECU. Check the exact vehicle, market, engine, original ECU and board part number against the manufacturer's HC20X installation manual.

Identification and installation

Record the Link model label and revision, donor factory ECU connector and car's engine and year. Plug-in boards connect to particular factory-harness layouts; the family or vehicle name alone does not establish every model-year or transmission combination. The manufacturer manual gives the supported application and any installation or configuration notes for this board.

G4X plug-in platforms offer configurable fuel and ignition control but available channels and features depend on the original header and board. The G4X plug-in general specifications are conditional on the particular application and do not mean every input is brought out to the factory harness.

Pinout and tuning

The HC20X installation manual is the model-specific source for board pinouts, expansion connections, electrical cautions and startup configuration. Use its connector orientation and the exact board version; do not copy a wire-in ECU pinout onto a factory harness. PCLink and manual downloads; Link manufacturer overview.

Manufacturer connector schedules

From Link's HC20X installation manual. Link describes the view as looking into the ECU from the wire side. A dash reproduces an unspecified source field; nc is Link's label. Confirm the vehicle and board revision before use. This guide identifies the DC5 Integra Type R and compatible Civic generation 7 applications. A/C request is received over K-Line on CAN DI 1. Link says Aux 15 must be on (active low) for correct operation. The internal MAP input is selected with a jumper.

Factory main header

Factory pinLink ECU channelFactory functionA1Injector 7 (Aux)NB O2 Heater ControlE1Aux 1Fuel Pump RelayA2+14V ECU Power—E2An Volt 7Secondary NB O2 SignalA3+14V ECU Power—E3Ground—A4Ground (Power)—E4Ground (Signal)—A5Ground (Power)—E5+5V Out—A6An Volt 11NB O2 SignalE6Injector 8 (Aux)Secondary NB O2 Heater ControlA7Trigger 1Crank Position SensorE7Main RelayControlled by Ignition Switch (E9)A8An Volt 10Intake Runner Position, (2002-2004 RSX K20A3 and 2002-2004 CRV K24A1 only)E8Injector 5 (Aux)O2 Heater Control Relay (Controls +12V supply to both NB O2 heaters)A9Knock 1Knock SensorE9DI10Ignition Switch InputA10Ground (Signal)—E10nc—A11Ground (Signal)—E11nc—A12Aux 5Idle Solenoid (IACV)E12nc—A13An Volt 12EGR Position, (2001- 2005 Civic D17A2/D17A6 only)E13nc—A14Injector 6 (Aux)Secondary O2 Heater, (2001-2005 Civic D17A2/D17A6 only)E14An Volt 9Fuel Tank PressureA15An Volt 2TPSE15An Volt 8Electrical LoadA16Ground (Signal)Primary O2 Signal GroundE16DI 3PS Pressure SwitchA17nc—E17nc—A18DI 2Vehicle SpeedE18Ignition 6 (Aux)AC ClutchA19An Volt 1Factory MAP Sensor (Via Jumper)E19nc—A20+5V Out—E20Aux 12EVAP emissions bypass solenoid valveA21+5V Out—E21Aux 11EVAP emmisions canister vent shut valveA22nc—E22DI 4Brake Pedal SwitchA23Ground—E23nc—A24Ground—E24KLineCommunicates with vehicle (temp gauge, ac switch, batt light)A25DI 1VVT Cam Position (K Series)E25nc—A26Trigger 2Cam Sync SensorE26Aux 3TachoA27Ignition 4IgnitionE27KLineCommunicates with the ImmobiliserA28Ignition 3IgnitionE28nc—A29Ignition 2IgnitionE29nc—A30Ignition 1IgnitionE30nc—A31nc—E31Ignition 5 (Aux)CE LightB1+14V OutVTC Oil Control Sol +veB2Injector 4InjectionB3Injector 3InjectionB4Injector 2InjectionB5Injector 1InjectionB6Aux 13Radiator Fan RelayB7Aux 4Reverse Lockout Solenoid (K20A2)B8An Temp 1ECTB9DI 5VTEC Oil Pressure SwitchB10nc—B11nc—B12nc—B13nc—B14nc—B15Aux 14VTEC Solenoid (Drives High Side)B16nc—B17An Temp 2IATB18Aux 8Alternator ControlB19nc—B20nc—B21Ignition 8 (Aux)Evap PurgeB22Ignition 7 (Aux)Intake Runner ControlB23Aux 2VTC Oil Control Sol -veB24nc—

Expansion connector

PositionLink ECU channelFunctionExpansion 1Ground (Signal)—Expansion 2+5V Out—Expansion 3Aux 9—Expansion 4Aux 10—Expansion 5An Volt 4—Expansion 6An Volt 5—Expansion 7An Volt 6—Expansion 8An Volt 3—Expansion 9An Temp 4—Expansion 10An Temp 3—Expansion 11DI 9—Expansion 12DI 8—Expansion 13DI 7—Expansion 14DI 6—Expansion 15Aux 7—Expansion 16Aux 6—

Other connections

PositionLink ECU channelFunctionOn-Board MAPAn Volt 1Jumper connects An Volt 1 to this or A19E-Throttle RelayAux 16Only used when adding E- ThrottleOn-Board power RelayAux 15Used to prevent back feeding

CAN Connector

PinFunctionWire colour1Comms GNDBrown2CAN LGreen3CAN HWhite4+14VYellow

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 3: Link G4X HC20X plug-in ECU
Link G4X HC20X plug-in ECU
Manufacturer product image of HC20X application ECU: Link ECU. Permission to republish confirmed by the user.

Link G4X HC20X is a vehicle-specific programmable plug-in ECU for the Honda K20 / DC5 application listed in Link's model-specific manuals index. It is an application board, rather than the universal wire-in ECU. Check the exact vehicle, market, engine, original ECU and board part number against the manufacturer's HC20X installation manual.

Identification and installation

Record the Link model label and revision, donor factory ECU connector and car's engine and year. Plug-in boards connect to particular factory-harness layouts; the family or vehicle name alone does not establish every model-year or transmission combination. The manufacturer manual gives the supported application and any installation or configuration notes for this board.

G4X plug-in platforms offer configurable fuel and ignition control but available channels and features depend on the original header and board. The G4X plug-in general specifications are conditional on the particular application and do not mean every input is brought out to the factory harness.

Pinout and tuning

The HC20X installation manual is the model-specific source for board pinouts, expansion connections, electrical cautions and startup configuration. Use its connector orientation and the exact board version; do not copy a wire-in ECU pinout onto a factory harness. PCLink and manual downloads; Link manufacturer overview.

Manufacturer connector schedules

From Link's HC20X installation manual. Link describes the view as looking into the ECU from the wire side. A dash reproduces an unspecified source field; nc is Link's label. Confirm the vehicle and board revision before use. This guide identifies the DC5 Integra Type R and compatible Civic generation 7 applications. A/C request is received over K-Line on CAN DI 1. Link says Aux 15 must be on (active low) for correct operation. The internal MAP input is selected with a jumper.

Factory main header

Factory pinLink ECU channelFactory function
A1Injector 7 (Aux)NB O2 Heater Control
E1Aux 1Fuel Pump Relay
A2+14V ECU Power—
E2An Volt 7Secondary NB O2 Signal
A3+14V ECU Power—
E3Ground—
A4Ground (Power)—
E4Ground (Signal)—
A5Ground (Power)—
E5+5V Out—
A6An Volt 11NB O2 Signal
E6Injector 8 (Aux)Secondary NB O2 Heater Control
A7Trigger 1Crank Position Sensor
E7Main RelayControlled by Ignition Switch (E9)
A8An Volt 10Intake Runner Position, (2002-2004 RSX K20A3 and 2002-2004 CRV K24A1 only)
E8Injector 5 (Aux)O2 Heater Control Relay (Controls +12V supply to both NB O2 heaters)
A9Knock 1Knock Sensor
E9DI10Ignition Switch Input
A10Ground (Signal)—
E10nc—
A11Ground (Signal)—
E11nc—
A12Aux 5Idle Solenoid (IACV)
E12nc—
A13An Volt 12EGR Position, (2001- 2005 Civic D17A2/D17A6 only)
E13nc—
A14Injector 6 (Aux)Secondary O2 Heater, (2001-2005 Civic D17A2/D17A6 only)
E14An Volt 9Fuel Tank Pressure
A15An Volt 2TPS
E15An Volt 8Electrical Load
A16Ground (Signal)Primary O2 Signal Ground
E16DI 3PS Pressure Switch
A17nc—
E17nc—
A18DI 2Vehicle Speed
E18Ignition 6 (Aux)AC Clutch
A19An Volt 1Factory MAP Sensor (Via Jumper)
E19nc—
A20+5V Out—
E20Aux 12EVAP emissions bypass solenoid valve
A21+5V Out—
E21Aux 11EVAP emmisions canister vent shut valve
A22nc—
E22DI 4Brake Pedal Switch
A23Ground—
E23nc—
A24Ground—
E24KLineCommunicates with vehicle (temp gauge, ac switch, batt light)
A25DI 1VVT Cam Position (K Series)
E25nc—
A26Trigger 2Cam Sync Sensor
E26Aux 3Tacho
A27Ignition 4Ignition
E27KLineCommunicates with the Immobiliser
A28Ignition 3Ignition
E28nc—
A29Ignition 2Ignition
E29nc—
A30Ignition 1Ignition
E30nc—
A31nc—
E31Ignition 5 (Aux)CE Light
B1+14V OutVTC Oil Control Sol +ve
B2Injector 4Injection
B3Injector 3Injection
B4Injector 2Injection
B5Injector 1Injection
B6Aux 13Radiator Fan Relay
B7Aux 4Reverse Lockout Solenoid (K20A2)
B8An Temp 1ECT
B9DI 5VTEC Oil Pressure Switch
B10nc—
B11nc—
B12nc—
B13nc—
B14nc—
B15Aux 14VTEC Solenoid (Drives High Side)
B16nc—
B17An Temp 2IAT
B18Aux 8Alternator Control
B19nc—
B20nc—
B21Ignition 8 (Aux)Evap Purge
B22Ignition 7 (Aux)Intake Runner Control
B23Aux 2VTC Oil Control Sol -ve
B24nc—

Expansion connector

PositionLink ECU channelFunction
Expansion 1Ground (Signal)—
Expansion 2+5V Out—
Expansion 3Aux 9—
Expansion 4Aux 10—
Expansion 5An Volt 4—
Expansion 6An Volt 5—
Expansion 7An Volt 6—
Expansion 8An Volt 3—
Expansion 9An Temp 4—
Expansion 10An Temp 3—
Expansion 11DI 9—
Expansion 12DI 8—
Expansion 13DI 7—
Expansion 14DI 6—
Expansion 15Aux 7—
Expansion 16Aux 6—

Other connections

PositionLink ECU channelFunction
On-Board MAPAn Volt 1Jumper connects An Volt 1 to this or A19
E-Throttle RelayAux 16Only used when adding E- Throttle
On-Board power RelayAux 15Used to prevent back feeding

CAN Connector

PinFunctionWire colour
1Comms GNDBrown
2CAN LGreen
3CAN HWhite
4+14VYellow
Revision 3: Link G4X HC20X plug-in ECU
Link G4X HC20X plug-in ECU
Manufacturer product image of HC20X application ECU: Link ECU. Permission to republish confirmed by the user.

Link G4X HC20X is a vehicle-specific programmable plug-in ECU for the Honda K20 / DC5 application listed in Link's model-specific manuals index. It is an application board, rather than the universal wire-in ECU. Check the exact vehicle, market, engine, original ECU and board part number against the manufacturer's HC20X installation manual.

Identification and installation

Record the Link model label and revision, donor factory ECU connector and car's engine and year. Plug-in boards connect to particular factory-harness layouts; the family or vehicle name alone does not establish every model-year or transmission combination. The manufacturer manual gives the supported application and any installation or configuration notes for this board.

G4X plug-in platforms offer configurable fuel and ignition control but available channels and features depend on the original header and board. The G4X plug-in general specifications are conditional on the particular application and do not mean every input is brought out to the factory harness.

Pinout and tuning

The HC20X installation manual is the model-specific source for board pinouts, expansion connections, electrical cautions and startup configuration. Use its connector orientation and the exact board version; do not copy a wire-in ECU pinout onto a factory harness. PCLink and manual downloads; Link manufacturer overview.

Manufacturer connector schedules

From Link's HC20X installation manual. Link describes the view as looking into the ECU from the wire side. A dash reproduces an unspecified source field; nc is Link's label. Confirm the vehicle and board revision before use. This guide identifies the DC5 Integra Type R and compatible Civic generation 7 applications. A/C request is received over K-Line on CAN DI 1. Link says Aux 15 must be on (active low) for correct operation. The internal MAP input is selected with a jumper.

Factory main header

Factory pinLink ECU channelFactory function
A1Injector 7 (Aux)NB O2 Heater Control
E1Aux 1Fuel Pump Relay
A2+14V ECU Power—
E2An Volt 7Secondary NB O2 Signal
A3+14V ECU Power—
E3Ground—
A4Ground (Power)—
E4Ground (Signal)—
A5Ground (Power)—
E5+5V Out—
A6An Volt 11NB O2 Signal
E6Injector 8 (Aux)Secondary NB O2 Heater Control
A7Trigger 1Crank Position Sensor
E7Main RelayControlled by Ignition Switch (E9)
A8An Volt 10Intake Runner Position, (2002-2004 RSX K20A3 and 2002-2004 CRV K24A1 only)
E8Injector 5 (Aux)O2 Heater Control Relay (Controls +12V supply to both NB O2 heaters)
A9Knock 1Knock Sensor
E9DI10Ignition Switch Input
A10Ground (Signal)—
E10nc—
A11Ground (Signal)—
E11nc—
A12Aux 5Idle Solenoid (IACV)
E12nc—
A13An Volt 12EGR Position, (2001- 2005 Civic D17A2/D17A6 only)
E13nc—
A14Injector 6 (Aux)Secondary O2 Heater, (2001-2005 Civic D17A2/D17A6 only)
E14An Volt 9Fuel Tank Pressure
A15An Volt 2TPS
E15An Volt 8Electrical Load
A16Ground (Signal)Primary O2 Signal Ground
E16DI 3PS Pressure Switch
A17nc—
E17nc—
A18DI 2Vehicle Speed
E18Ignition 6 (Aux)AC Clutch
A19An Volt 1Factory MAP Sensor (Via Jumper)
E19nc—
A20+5V Out—
E20Aux 12EVAP emissions bypass solenoid valve
A21+5V Out—
E21Aux 11EVAP emmisions canister vent shut valve
A22nc—
E22DI 4Brake Pedal Switch
A23Ground—
E23nc—
A24Ground—
E24KLineCommunicates with vehicle (temp gauge, ac switch, batt light)
A25DI 1VVT Cam Position (K Series)
E25nc—
A26Trigger 2Cam Sync Sensor
E26Aux 3Tacho
A27Ignition 4Ignition
E27KLineCommunicates with the Immobiliser
A28Ignition 3Ignition
E28nc—
A29Ignition 2Ignition
E29nc—
A30Ignition 1Ignition
E30nc—
A31nc—
E31Ignition 5 (Aux)CE Light
B1+14V OutVTC Oil Control Sol +ve
B2Injector 4Injection
B3Injector 3Injection
B4Injector 2Injection
B5Injector 1Injection
B6Aux 13Radiator Fan Relay
B7Aux 4Reverse Lockout Solenoid (K20A2)
B8An Temp 1ECT
B9DI 5VTEC Oil Pressure Switch
B10nc—
B11nc—
B12nc—
B13nc—
B14nc—
B15Aux 14VTEC Solenoid (Drives High Side)
B16nc—
B17An Temp 2IAT
B18Aux 8Alternator Control
B19nc—
B20nc—
B21Ignition 8 (Aux)Evap Purge
B22Ignition 7 (Aux)Intake Runner Control
B23Aux 2VTC Oil Control Sol -ve
B24nc—

Expansion connector

PositionLink ECU channelFunction
Expansion 1Ground (Signal)—
Expansion 2+5V Out—
Expansion 3Aux 9—
Expansion 4Aux 10—
Expansion 5An Volt 4—
Expansion 6An Volt 5—
Expansion 7An Volt 6—
Expansion 8An Volt 3—
Expansion 9An Temp 4—
Expansion 10An Temp 3—
Expansion 11DI 9—
Expansion 12DI 8—
Expansion 13DI 7—
Expansion 14DI 6—
Expansion 15Aux 7—
Expansion 16Aux 6—

Other connections

PositionLink ECU channelFunction
On-Board MAPAn Volt 1Jumper connects An Volt 1 to this or A19
E-Throttle RelayAux 16Only used when adding E- Throttle
On-Board power RelayAux 15Used to prevent back feeding

CAN Connector

PinFunctionWire colour
1Comms GNDBrown
2CAN LGreen
3CAN HWhite
4+14VYellow