
Link G4X HC20X is a vehicle-specific programmable plug-in ECU for the Honda K20 / DC5 application listed in Link's model-specific manuals index. It is an application board, rather than the universal wire-in ECU. Check the exact vehicle, market, engine, original ECU and board part number against the manufacturer's HC20X installation manual.
Identification and installation
Record the Link model label and revision, donor factory ECU connector and car's engine and year. Plug-in boards connect to particular factory-harness layouts; the family or vehicle name alone does not establish every model-year or transmission combination. The manufacturer manual gives the supported application and any installation or configuration notes for this board.
G4X plug-in platforms offer configurable fuel and ignition control but available channels and features depend on the original header and board. The G4X plug-in general specifications are conditional on the particular application and do not mean every input is brought out to the factory harness.
Pinout and tuning
The HC20X installation manual is the model-specific source for board pinouts, expansion connections, electrical cautions and startup configuration. Use its connector orientation and the exact board version; do not copy a wire-in ECU pinout onto a factory harness. PCLink and manual downloads; Link manufacturer overview.
Manufacturer connector schedules
From Link's HC20X installation manual. Link describes the view as looking into the ECU from the wire side. A dash reproduces an unspecified source field; nc is Link's label. Confirm the vehicle and board revision before use. This guide identifies the DC5 Integra Type R and compatible Civic generation 7 applications. A/C request is received over K-Line on CAN DI 1. Link says Aux 15 must be on (active low) for correct operation. The internal MAP input is selected with a jumper.
Factory main header
| Factory pin | Link ECU channel | Factory function |
|---|---|---|
| A1 | Injector 7 (Aux) | NB O2 Heater Control |
| E1 | Aux 1 | Fuel Pump Relay |
| A2 | +14V ECU Power | — |
| E2 | An Volt 7 | Secondary NB O2 Signal |
| A3 | +14V ECU Power | — |
| E3 | Ground | — |
| A4 | Ground (Power) | — |
| E4 | Ground (Signal) | — |
| A5 | Ground (Power) | — |
| E5 | +5V Out | — |
| A6 | An Volt 11 | NB O2 Signal |
| E6 | Injector 8 (Aux) | Secondary NB O2 Heater Control |
| A7 | Trigger 1 | Crank Position Sensor |
| E7 | Main Relay | Controlled by Ignition Switch (E9) |
| A8 | An Volt 10 | Intake Runner Position, (2002-2004 RSX K20A3 and 2002-2004 CRV K24A1 only) |
| E8 | Injector 5 (Aux) | O2 Heater Control Relay (Controls +12V supply to both NB O2 heaters) |
| A9 | Knock 1 | Knock Sensor |
| E9 | DI10 | Ignition Switch Input |
| A10 | Ground (Signal) | — |
| E10 | nc | — |
| A11 | Ground (Signal) | — |
| E11 | nc | — |
| A12 | Aux 5 | Idle Solenoid (IACV) |
| E12 | nc | — |
| A13 | An Volt 12 | EGR Position, (2001- 2005 Civic D17A2/D17A6 only) |
| E13 | nc | — |
| A14 | Injector 6 (Aux) | Secondary O2 Heater, (2001-2005 Civic D17A2/D17A6 only) |
| E14 | An Volt 9 | Fuel Tank Pressure |
| A15 | An Volt 2 | TPS |
| E15 | An Volt 8 | Electrical Load |
| A16 | Ground (Signal) | Primary O2 Signal Ground |
| E16 | DI 3 | PS Pressure Switch |
| A17 | nc | — |
| E17 | nc | — |
| A18 | DI 2 | Vehicle Speed |
| E18 | Ignition 6 (Aux) | AC Clutch |
| A19 | An Volt 1 | Factory MAP Sensor (Via Jumper) |
| E19 | nc | — |
| A20 | +5V Out | — |
| E20 | Aux 12 | EVAP emissions bypass solenoid valve |
| A21 | +5V Out | — |
| E21 | Aux 11 | EVAP emmisions canister vent shut valve |
| A22 | nc | — |
| E22 | DI 4 | Brake Pedal Switch |
| A23 | Ground | — |
| E23 | nc | — |
| A24 | Ground | — |
| E24 | KLine | Communicates with vehicle (temp gauge, ac switch, batt light) |
| A25 | DI 1 | VVT Cam Position (K Series) |
| E25 | nc | — |
| A26 | Trigger 2 | Cam Sync Sensor |
| E26 | Aux 3 | Tacho |
| A27 | Ignition 4 | Ignition |
| E27 | KLine | Communicates with the Immobiliser |
| A28 | Ignition 3 | Ignition |
| E28 | nc | — |
| A29 | Ignition 2 | Ignition |
| E29 | nc | — |
| A30 | Ignition 1 | Ignition |
| E30 | nc | — |
| A31 | nc | — |
| E31 | Ignition 5 (Aux) | CE Light |
| B1 | +14V Out | VTC Oil Control Sol +ve |
| B2 | Injector 4 | Injection |
| B3 | Injector 3 | Injection |
| B4 | Injector 2 | Injection |
| B5 | Injector 1 | Injection |
| B6 | Aux 13 | Radiator Fan Relay |
| B7 | Aux 4 | Reverse Lockout Solenoid (K20A2) |
| B8 | An Temp 1 | ECT |
| B9 | DI 5 | VTEC Oil Pressure Switch |
| B10 | nc | — |
| B11 | nc | — |
| B12 | nc | — |
| B13 | nc | — |
| B14 | nc | — |
| B15 | Aux 14 | VTEC Solenoid (Drives High Side) |
| B16 | nc | — |
| B17 | An Temp 2 | IAT |
| B18 | Aux 8 | Alternator Control |
| B19 | nc | — |
| B20 | nc | — |
| B21 | Ignition 8 (Aux) | Evap Purge |
| B22 | Ignition 7 (Aux) | Intake Runner Control |
| B23 | Aux 2 | VTC Oil Control Sol -ve |
| B24 | nc | — |
Expansion connector
| Position | Link ECU channel | Function |
|---|---|---|
| Expansion 1 | Ground (Signal) | — |
| Expansion 2 | +5V Out | — |
| Expansion 3 | Aux 9 | — |
| Expansion 4 | Aux 10 | — |
| Expansion 5 | An Volt 4 | — |
| Expansion 6 | An Volt 5 | — |
| Expansion 7 | An Volt 6 | — |
| Expansion 8 | An Volt 3 | — |
| Expansion 9 | An Temp 4 | — |
| Expansion 10 | An Temp 3 | — |
| Expansion 11 | DI 9 | — |
| Expansion 12 | DI 8 | — |
| Expansion 13 | DI 7 | — |
| Expansion 14 | DI 6 | — |
| Expansion 15 | Aux 7 | — |
| Expansion 16 | Aux 6 | — |
Other connections
| Position | Link ECU channel | Function |
|---|---|---|
| On-Board MAP | An Volt 1 | Jumper connects An Volt 1 to this or A19 |
| E-Throttle Relay | Aux 16 | Only used when adding E- Throttle |
| On-Board power Relay | Aux 15 | Used to prevent back feeding |
CAN Connector
| Pin | Function | Wire colour |
|---|---|---|
| 1 | Comms GND | Brown |
| 2 | CAN L | Green |
| 3 | CAN H | White |
| 4 | +14V | Yellow |