Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
Motorsport Electronics ME221
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None
ME221 Honda S2000 AP1 plug-in ECU
ME221 Honda S2000 AP1 plug-in ECU. Manufacturer product image: Motorsport Electronics; used with permission.

ME221 plug-in ECU for Honda S2000 AP1. This application-specific unit replaces the factory ECU electronics while using the vehicle's original harness connector, subject to exact fitment and configuration. Motorsport Electronics product information · application installation guide.

Identification and application

ME's installation guide identifies Honda S2000 AP1 2000–05, whereas the product page describes 2000–04. Check the particular ECU and market rather than relying on year alone. Record the serial, board version, firmware, factory ECU part number, engine and transmission before installing. The ME221 and ME442 are separate hardware choices; the manufacturer lists wideband, onboard logging and EGT as ME442 plug-in features. Optional electronic throttle equipment and supported functions vary by board and configuration. See ME's model comparison and downloads.

Connector and pinout

Use the OEM header and auxiliary connector diagrams in the exact application installation guide. Connector view, jumper/switch settings, sensors and supported functions vary by generation and vehicle. The universal 28-way and 90-way wire-in tables do not define this plug-in board's factory header.

Software and installation

Use the correct MEITE / EZ Tune release and the model-specific firmware and base map. The installation guide covers sensor settings, baseline checks, expansion, jumper settings and any vehicle-specific exceptions; a base map still needs calibration and verification on the actual engine. See the ME221 family page for wire-in generation and hardware context.

Sources reviewed 17 November 2026.

Manufacturer S2000 connector schedules

These are the positions explicitly listed in Appendix A of the manufacturer’s ME221/ME442 S2000 AP1 Gen1 and Gen2/2B installation guide. The two I/O columns reflect the guide’s distinct board generations. A dash or “not specified” preserves the source’s missing entry; it does not establish that a cavity is unconnected. The actual model, generation, DBW hardware and firmware determine available functions. The guide identifies the D connector as TE 179678-6.

PinVehicle / connector functionGEN1 I/OGEN2 / GEN2B I/O
A1Coolant dashboard gaugeLS10LS 3
A2Air control valvedrvSLS7LS 7
A3EVAP bypass solenoid ventdrvSLS8LS 16
A4EVAP canister ventLS 2LS 8
A6EVAP purgeLS 1LS 4
A9VSSHS DIGIN 1DIGIN 4
A12Immobiliser indicator lightdrvSLS4LS 17
A15Fuel pump relaydrvSLS1LS 11
A17AC clutch relaydrvSLS5LS 14
A18CEL lightdrvSLS2LS 13
A19Tacho outputTACHOTACHO
A20Primary radiator fandrvSLS3LS 15
A27AC switch signaldrvDIGIN3DIGIN 5
A28Air pump relaydrvSLS6LS 18
A29Fuel tank pressure sensorANAV 6ANAV 6
A30Electronic load detectorANAV 9ANAV 5
B1Switched 12 V ignition12VIGN12VIGN
B3Injector 2LS 5Injector 2
B4Injector 3LS 6Injector 3
B5Injector 4LS 7Injector 4
B11Injector 1LS 4Injector 1
B12VTEC solenoidLS 12COIL 5
B14Spare low-side 9 A driverLS 11LS 1
B15Spare low-side 9 A driverLS 9LS 2
B23Idle control valveLS 3LS 9
C3Knock sensor positiveKnock 1Not specified
C4Ignition coil 1COIL ACoil 1
C8Crank signal positiveNot specifiedNot specified
C9Crank signal negativeNot specifiedNot specified
C12Ignition coil 2COIL BCoil 2
C13Ignition coil 3COIL CCoil 3
C14Ignition coil 4COIL DCoil 4
C15O2 signal 2ANA-V7—
C16O2 signal 1ANA-V3AnaV 3
C17MAP signalANA-V1 (OEM MAP)OEM MAP ANAV1; on-board 4 bar ANAV4
C20/C21Cam positive / cam negativeNot specifiedNot specified
C22Knock sensor negativeNot specifiedNot specified
C25Intake air temperature signalANA-T1ANAT 1
C26Coolant sensor signalANA-T2ANAT 2
C27Throttle position signalANA-V2ANAV 2
D1GEN1 digital input / GEN2 injectordrvDIGIN1Injector 5
D2GEN1 digital input / GEN2 injectordrvDIGIN2Injector 6
D3GEN2 spare low side—Injector 7
D4GEN1 digital input / GEN2 injectordrvDIGIN4Injector 8
D5GEN2 spare analogue input—ANAT 3
D6GEN2 spare analogue input—ANAT 4
D7GEN2 DBW HBA 1—DBW HBA 1
D8GEN2 DBW HBA 2drvDIGIN5DBW HBA 2
D9GEN2 low side—LS 10
D10GEN1 analogue input / GEN2 EGTAna-V8EGT signal
D11CAN bus lowCANBusCANBus
D12CAN bus highCANBusCANBus
D135 V low-current sensor supply5V5V
D14Sensor groundGNDGND

The guide groups C20/C21 as cam positive / cam negative; verify the actual polarity and connector view with the manufacturer drawing and vehicle loom. It also labels D8 as GEN2 DBW HBA 2 while listing a GEN1 digital input in the adjacent column; the original wording is preserved.