Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
Syvecs Standalone ECUs
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Changes from revision 2 to revision 2

Removed text is struck through; added text is highlighted.

Syvecs S7Plus general-purpose ECU shown as a family reference; vehicle-specific kit and adaptor may differ. Manufacturer photograph, reproduced with permission. Image source.

Model and vehicle application

Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Polaris Pro R, with product code S7Plus- Polaris-PROR-DF. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.

This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.

Wiring and pinout

Syvecs Polaris Pro R installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.

For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.

Calibration and service

Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.

Sources

Syvecs Polaris Pro R product listing and applicationManufacturer kit installation and pinout manualSyvecs plug-in kit support index

Additional 26-way I/O connector

From the Syvecs Polaris RZR Pro R installation guide. Pins 18–19 are identified as EGT/CAN3 alternatives; check configuration for the installed hardware. This is the documented additional connector only; the table is not a complete factory vehicle connector pinout. Confirm the connector view and hardware configuration in the guide.

PinFunction1Ground2Fuel 53Fuel 64Fuel 75Fuel 86Fuel 97Vbat8Lambda 1 heater9Lambda 1 A10Lambda 1 B11Lambda 1 D12RS232 RX13RS232 TX14AN515AN716AN1117+5 V18EGT− / CAN3 L19EGT+ / CAN3 H20Analogue ground21CAN2 H22CAN2 L23LAN RX−24LAN RX+25LAN TX−26LAN TX+

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 2: Syvecs Polaris Pro R Plug-in ECU
Syvecs S7Plus general-purpose ECU
Syvecs S7Plus general-purpose ECU shown as a family reference; vehicle-specific kit and adaptor may differ. Manufacturer photograph, reproduced with permission. Image source.

Model and vehicle application

Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Polaris Pro R, with product code S7Plus- Polaris-PROR-DF. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.

This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.

Wiring and pinout

Syvecs Polaris Pro R installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.

For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.

Calibration and service

Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.

Sources

Additional 26-way I/O connector

From the Syvecs Polaris RZR Pro R installation guide. Pins 18–19 are identified as EGT/CAN3 alternatives; check configuration for the installed hardware. This is the documented additional connector only; the table is not a complete factory vehicle connector pinout. Confirm the connector view and hardware configuration in the guide.

PinFunction
1Ground
2Fuel 5
3Fuel 6
4Fuel 7
5Fuel 8
6Fuel 9
7Vbat
8Lambda 1 heater
9Lambda 1 A
10Lambda 1 B
11Lambda 1 D
12RS232 RX
13RS232 TX
14AN5
15AN7
16AN11
17+5 V
18EGT− / CAN3 L
19EGT+ / CAN3 H
20Analogue ground
21CAN2 H
22CAN2 L
23LAN RX−
24LAN RX+
25LAN TX−
26LAN TX+
Revision 2: Syvecs Polaris Pro R Plug-in ECU
Syvecs S7Plus general-purpose ECU
Syvecs S7Plus general-purpose ECU shown as a family reference; vehicle-specific kit and adaptor may differ. Manufacturer photograph, reproduced with permission. Image source.

Model and vehicle application

Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Polaris Pro R, with product code S7Plus- Polaris-PROR-DF. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.

This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.

Wiring and pinout

Syvecs Polaris Pro R installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.

For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.

Calibration and service

Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.

Sources

Additional 26-way I/O connector

From the Syvecs Polaris RZR Pro R installation guide. Pins 18–19 are identified as EGT/CAN3 alternatives; check configuration for the installed hardware. This is the documented additional connector only; the table is not a complete factory vehicle connector pinout. Confirm the connector view and hardware configuration in the guide.

PinFunction
1Ground
2Fuel 5
3Fuel 6
4Fuel 7
5Fuel 8
6Fuel 9
7Vbat
8Lambda 1 heater
9Lambda 1 A
10Lambda 1 B
11Lambda 1 D
12RS232 RX
13RS232 TX
14AN5
15AN7
16AN11
17+5 V
18EGT− / CAN3 L
19EGT+ / CAN3 H
20Analogue ground
21CAN2 H
22CAN2 L
23LAN RX−
24LAN RX+
25LAN TX−
26LAN TX+