Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
Link standalone ECUs
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None
Link G4X JZX90X plug-in ECU
Manufacturer product image of JZX90X application ECU: Link ECU. Permission to republish confirmed by the user.

Link G4X JZX90X is a vehicle-specific programmable plug-in ECU for the Toyota JZX90 application listed in Link's model-specific manuals index. It is an application board rather than a universal wire-in ECU. Check the exact vehicle, market, engine, original ECU and board part number against the manufacturer's JZX90X installation manual.

Identification and installation

Record the Link model label and revision, donor factory ECU connector and car's engine and year. Plug-in boards connect to particular factory-harness layouts; the family or vehicle name alone does not establish every model-year or transmission combination. The manufacturer manual gives the supported application and any installation or configuration notes for this board.

G4X plug-in platforms offer configurable fuel and ignition control but available channels and features depend on the original header and board. The G4X plug-in general specifications are conditional on the particular application and do not mean every input is brought out to the factory harness.

Pinout and tuning

The JZX90X installation manual is the model-specific source for board pinouts, expansion connections, electrical cautions and startup configuration. Use its connector orientation and the exact board version; do not copy a wire-in ECU pinout onto a factory harness. PCLink and manual downloads; Link manufacturer overview.

Manufacturer connector schedules

From Link's JZX90 installation manual. Pinouts are viewed looking into the ECU from the wire side. A dash reproduces an unspecified source field; nc is Link's label. Confirm the exact board revision and vehicle harness before use.

Injector drive 8 controls the main relay through dedicated high-side hardware. Link reports that on V1.4 and earlier boards Aux 6 and Aux 7 idle-stepper wiring is reversed. Follow the source guide for the affected revision.

Factory main header

Factory pinLink ECU channelFactory function
1Injector 1Injection
65nc—
2Injector 2Injection
66nc—
3Injector 3Injection
67nc—
4Aux 1Purge
68Ground—
5nc—
69nc—
6Knock 1Knock
70nc—
7Knock 2Knock
71nc—
8Injector 7 (Aux)NB O2 Heater
72nc—
9nc—
73nc—
10nc—
74nc—
11Ignition 2Ignition
75nc—
12Ignition 3Ignition
76Ignition 7AC Clutch
13nc—
77nc—
14DI 1Start Switch
78nc—
15nc—
79nc—
16nc—
80nc—
17Ignition 4Ignition
81nc—
18nc—
82DI 3Gearbox Speed
19Ignition 1Ignition
83nc—
20Aux 5ISC Stepper
84nc—
21Aux 6ISC Stepper
85DI 5Ignition Switch (Controls Main Relay Output)
22Aux 7ISC Stepper
86nc—
23Aux 8ISC Stepper
87DI 6AC Request
24nc—
88nc—
25nc—
89nc—
26nc—
90nc—
27Ground (Signal)—
91nc—
28Ground (Signal)—
92nc—
29nc—
93+12V Hot feedUsed for Hold Power and Flywheeling
30nc—
94nc—
31Ignition 5Ignition
95nc—
32Ignition 6Ignition
96nc—
33Ground—
97nc—
34nc—
98nc—
35Ground (Triggers)—
99+14VECU Power
36Trig 1Trigger 1
100+14VECU Power
37nc—
38nc—
39nc—
40+5V Out—
41Ground (Triggers)—
42Trig 2Trigger 2
43nc—
44An Volt 1 via jumperFactory MAP Sensor
45An Volt 2TPS
46Ground (Triggers)—
47DI 2Another CAM Sensor
48nc—
49An Temp 2IAT
50An Volt 3NB O2 Sensor
51VTA2Buffered copy sent out pin 64
52Ground—
53nc—
54An Temp 1ECT
55nc—
56nc—
57Aux 2FP Speed (PWM)
58Aux 3CE Light
59Main Relay OutputPull high to activate
60Trig 1Trigger 1 Output
61Buffered Copy of An Volt 2—
62DI 4Timing Retard Request
63nc—
64Buffered Copy of VTA2 (Pin 51)—

Expansion connector

PositionLink ECU channelFunction
Expansion 1Ground (Signal)—
Expansion 2+5V Out—
Expansion 3Injector 4—
Expansion 4Injector 5—
Expansion 5Injector 6—
Expansion 6Aux 4—
Expansion 7An Temp 4—
Expansion 8An Temp 3—
Expansion 9Ground (Signal)—
Expansion 10+5V Out—
Expansion 11DI 7—
Expansion 12DI 8—
Expansion 13DI 9—
Expansion 14An Volt 8—
Expansion 15An Volt 9—
Expansion 16An Volt 10—

Electronic throttle connector

PositionLink ECU channelFunction
E-Throttle plug 1Ground (Signal)—
E-Throttle plug 2+5V Out—
E-Throttle plug 3An Volt 4—
E-Throttle plug 4An Volt 5—
E-Throttle plug 5An Volt 6—
E-Throttle plug 6An Volt 7—
E-Throttle plug 7Aux 10—
E-Throttle plug 8Aux 9—

Other documented connections

PositionLink ECU channelFunction
Main Relay ControlInjector 8ECU Hold Power
On Board MAPAn Volt 1 via jumperMAP
E-Throttle RelayAux 16(Only needed if converting to E-Throttle)

CAN 1 and 2 four-pin connector

PinFunctionWire colour
1GNDBlack
2CAN LGreen
3CAN HWhite
4+14VRed