Removed text is struck through; added text is highlighted.
Syvecs S7Plus general-purpose ECU shown as a family reference; vehicle-specific kit and adaptor may differ. Manufacturer photograph, reproduced with permission. Image source.
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Audi TTRS RS3 Mk3 8V1 S7Plus, with product code S7Plus-RS38V1. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs Audi TTRS RS3 Mk3 8V1 S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
Sources
Syvecs Audi TTRS RS3 Mk3 8V1 S7Plus product listing and applicationManufacturer kit installation and pinout manualSyvecs plug-in kit support index
Manufacturer ECU connector schedules
From the Syvecs Audi RS3/TTRS 8V1 installation guide, revision 1.2. The tables list ECU-side positions and the manufacturer's kit notes, not complete original vehicle connector pinouts. The guide limits this schedule to CZGB engines. It describes B18 as LAM2HEATER in one column and Slave Out 10 in another; verify that conflicting assignment with Syvecs. A dash denotes an empty field in the manufacturer chart; confirm the exact loom and connector view.
Connector A
PinSyvecs descriptionFunctionApplication notesA1PWR CTR OUTMAIN RELAY OUTPUTMain RelayA2H-Bridge1 / SlaveOut1H-Bridge1DBW +A3H-Bridge2 / SlaveOut2H-Bridge2DBW -A4H-Bridge3 / SlaveOut3H-Bridge3Tacho WireA5H-Bridge4 / SlaveOut4H-Bridge4FanA6H-Bridge5 / SlaveOut5H-Bridge5Valve for Oil Pressure ControlA7H-Bridge6 / SlaveOut6H-Bridge6Starter RelayA8H-Bridge7 / SlaveOut7H-Bridge7Charcoal SolenoidA9H-Bridge8 / SlaveOut8H-Bridge8Intake Fuel PumpA10FUEL1INJECTOR or PWM OUTPUTPrimary Injector 1A11FUEL2INJECTOR or PWM OUTPUTPrimary Injector 2A12FUEL3INJECTOR or PWM OUTPUTPrimary Injector 3A13FUEL4INJECTOR or PWM OUTPUTPrimary Injector 4A14FUEL5INJECTOR or PWM OUTPUTPrimary Injector 5A15FUEL6INJECTOR or PWM OUTPUTPort Injector 1 (External)A16FUEL7INJECTOR or PWM OUTPUTPort Injector 2 (External)A17FUEL8INJECTOR or PWM OUTPUTPort Injector 3 (External)A18FUEL9INJECTOR or PWM OUTPUTPort Injector 4 (External)A19FUEL10INJECTOR or PWM OUTPUTPort Injector 5 (External)A20FUEL11INJECTOR or PWM OUTPUTExhaust FlapA21FUEL12INJECTOR or PWM OUTPUTBoost SolenoidA22FUEL13INJECTOR or PWM OUTPUTTurbo Recirc (N249)A23FUEL14INJECTOR or PWM OUTPUTIntake Flap Control SolenoidA24FUEL15INJECTOR or PWM OUTPUTVVT1 Int (N205)A25FUEL16INJECTOR or PWM OUTPUTVVT1 Ex (N316)A26IGN1CYL 1 IGNITION OUTPUTIGN1 (N70)A27IGN2CYL 2 IGNITION OUTPUTIGN2 (N127)A28IGN3CYL 3 IGNITION OUTPUTIGN3 (N291)A29IGN4CYL 4 IGNITION OUTPUTIGN4 (N292)A30IGN5CYL 5 IGNITION OUTPUTIGN5 (N292)A31IGN6CYL 6 IGNITION OUTPUTDI Pump ControlA32PWRGNDPOWER GROUNDPwrGndA33PWRGNDPOWER GROUNDPwrGNdA34PWRGNDPOWER GROUNDPwrGNd
Connector B
PinSyvecs descriptionFunctionApplication notesB1PWRGNDPOWER GROUNDPWRGROUNDB2CAN2L——B3CAN2H——B4KNOCKKNOCKKnock +B5KNOCK 2KNOCK 2—B6PVBATCONSTANT 12V—B7IVBAT12v—B8LAM1ALamv / LamD1+/ LamLun1Pin6 on LSU4.9 ConnectorB9LAM1BLami / LamD1- /LamIP1Pin1 on LSU4.9 ConnectorB10LAM1CLamLIA1Pin5 on LSU4.9 ConnectorB11LAM1DLamGND / LamLVM1Pin2 on LSU4.9 ConnectorB12LAM1HEATERLAMBDA HEATERPin3 on LSU4.9 ConnectorB13IVBAT12 V—B14LAM2ALamv / LamD1+/ LamLun1—B15LAM2BLami / LamD1- /LamIP1—B16LAM2CLamLIA1—B17LAM2DLamGND / LamLVM1—B18LAM2HEATERSlave Out 10—B19IVBAT12 V—B20KLINEKline—B21RS232RXRS232RX—B22RS232TXRS232TX—B23LANRX-Cat5 Pin2—B24LANRX+Cat5 Pin1—B25LANTX-Cat5 Pin6—B26LANTX+Cat5 Pin3—
Open each version to inspect formatting, tables and photographs.
Revision 2: Syvecs Audi TTRS RS3 Mk3 8V1 S7Plus Plug-in ECUSyvecs S7Plus general-purpose ECU shown as a family reference; vehicle-specific kit and adaptor may differ. Manufacturer photograph, reproduced with permission. Image source.
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Audi TTRS RS3 Mk3 8V1 S7Plus, with product code S7Plus-RS38V1. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs Audi TTRS RS3 Mk3 8V1 S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
From the Syvecs Audi RS3/TTRS 8V1 installation guide, revision 1.2. The tables list ECU-side positions and the manufacturer's kit notes, not complete original vehicle connector pinouts. The guide limits this schedule to CZGB engines. It describes B18 as LAM2HEATER in one column and Slave Out 10 in another; verify that conflicting assignment with Syvecs. A dash denotes an empty field in the manufacturer chart; confirm the exact loom and connector view.
Connector A
Pin
Syvecs description
Function
Application notes
A1
PWR CTR OUT
MAIN RELAY OUTPUT
Main Relay
A2
H-Bridge1 / SlaveOut1
H-Bridge1
DBW +
A3
H-Bridge2 / SlaveOut2
H-Bridge2
DBW -
A4
H-Bridge3 / SlaveOut3
H-Bridge3
Tacho Wire
A5
H-Bridge4 / SlaveOut4
H-Bridge4
Fan
A6
H-Bridge5 / SlaveOut5
H-Bridge5
Valve for Oil Pressure Control
A7
H-Bridge6 / SlaveOut6
H-Bridge6
Starter Relay
A8
H-Bridge7 / SlaveOut7
H-Bridge7
Charcoal Solenoid
A9
H-Bridge8 / SlaveOut8
H-Bridge8
Intake Fuel Pump
A10
FUEL1
INJECTOR or PWM OUTPUT
Primary Injector 1
A11
FUEL2
INJECTOR or PWM OUTPUT
Primary Injector 2
A12
FUEL3
INJECTOR or PWM OUTPUT
Primary Injector 3
A13
FUEL4
INJECTOR or PWM OUTPUT
Primary Injector 4
A14
FUEL5
INJECTOR or PWM OUTPUT
Primary Injector 5
A15
FUEL6
INJECTOR or PWM OUTPUT
Port Injector 1 (External)
A16
FUEL7
INJECTOR or PWM OUTPUT
Port Injector 2 (External)
A17
FUEL8
INJECTOR or PWM OUTPUT
Port Injector 3 (External)
A18
FUEL9
INJECTOR or PWM OUTPUT
Port Injector 4 (External)
A19
FUEL10
INJECTOR or PWM OUTPUT
Port Injector 5 (External)
A20
FUEL11
INJECTOR or PWM OUTPUT
Exhaust Flap
A21
FUEL12
INJECTOR or PWM OUTPUT
Boost Solenoid
A22
FUEL13
INJECTOR or PWM OUTPUT
Turbo Recirc (N249)
A23
FUEL14
INJECTOR or PWM OUTPUT
Intake Flap Control Solenoid
A24
FUEL15
INJECTOR or PWM OUTPUT
VVT1 Int (N205)
A25
FUEL16
INJECTOR or PWM OUTPUT
VVT1 Ex (N316)
A26
IGN1
CYL 1 IGNITION OUTPUT
IGN1 (N70)
A27
IGN2
CYL 2 IGNITION OUTPUT
IGN2 (N127)
A28
IGN3
CYL 3 IGNITION OUTPUT
IGN3 (N291)
A29
IGN4
CYL 4 IGNITION OUTPUT
IGN4 (N292)
A30
IGN5
CYL 5 IGNITION OUTPUT
IGN5 (N292)
A31
IGN6
CYL 6 IGNITION OUTPUT
DI Pump Control
A32
PWRGND
POWER GROUND
PwrGnd
A33
PWRGND
POWER GROUND
PwrGNd
A34
PWRGND
POWER GROUND
PwrGNd
Connector B
Pin
Syvecs description
Function
Application notes
B1
PWRGND
POWER GROUND
PWRGROUND
B2
CAN2L
—
—
B3
CAN2H
—
—
B4
KNOCK
KNOCK
Knock +
B5
KNOCK 2
KNOCK 2
—
B6
PVBAT
CONSTANT 12V
—
B7
IVBAT
12v
—
B8
LAM1A
Lamv / LamD1+/ LamLun1
Pin6 on LSU4.9 Connector
B9
LAM1B
Lami / LamD1- /LamIP1
Pin1 on LSU4.9 Connector
B10
LAM1C
LamLIA1
Pin5 on LSU4.9 Connector
B11
LAM1D
LamGND / LamLVM1
Pin2 on LSU4.9 Connector
B12
LAM1HEATER
LAMBDA HEATER
Pin3 on LSU4.9 Connector
B13
IVBAT
12 V
—
B14
LAM2A
Lamv / LamD1+/ LamLun1
—
B15
LAM2B
Lami / LamD1- /LamIP1
—
B16
LAM2C
LamLIA1
—
B17
LAM2D
LamGND / LamLVM1
—
B18
LAM2HEATER
Slave Out 10
—
B19
IVBAT
12 V
—
B20
KLINE
Kline
—
B21
RS232RX
RS232RX
—
B22
RS232TX
RS232TX
—
B23
LANRX-
Cat5 Pin2
—
B24
LANRX+
Cat5 Pin1
—
B25
LANTX-
Cat5 Pin6
—
B26
LANTX+
Cat5 Pin3
—
Connector C
Pin
Syvecs description
Function
Application notes
C1
KNOCKGND
KNOCKGND
Knock -
C2
ANGND
SENSOR GND
—
C3
ANGND
SENSOR GND
—
C4
ANGND
SENSOR GND
—
C5
5V OUT
5V OUT
—
C6
5V OUT
5V OUT
—
C7
5V OUT
5V OUT
—
C8
CAN L
Can Low
Powertrain Can
C9
CAN H
Can High
Powertrain Can
C10
AN01
BI-POLAR INPUTS
Di Pressure
C11
AN02
BI-POLAR INPUTS
MapSensor
C12
AN03
BI-POLAR INPUTS
Charge Pressure
C13
AN04
BI-POLAR INPUTS
Brake
C14
AN05
UNI-POLAR INPUTS
—
C15
AN06
UNI-POLAR INPUTS
VVT1Ex Pos
C16
AN07
UNI-POLAR INPUTS
Crank Sensor
C17
AN08
UNI-POLAR INPUTS
Starter Request
C18
AN09
VOLT-INPUTS
TPS1A
C19
AN10
VOLT-INPUTS
TPS1B
C20
AN11
VOLT-INPUTS
PPSA
C21
AN12
VOLT-INPUTS
PPSB
C22
AN13
RESISTIVE INPUTS
—
C23
AN14
RESISTIVE INPUTS
Intake Air Temp
C24
AN15
RESISTIVE INPUTS
Coolant Temp
C25
AN16
RESISTIVE INPUTS
Oil Pressure Sw
C26
EGT1-
EGT1 -
—
C27
EGT1+
EGT1 +
—
C28
PWR CTR IN
MAIN RELAY INPUT SW
Key On sig (15)
C29
AN S1 / Slave An01
UNI-POLAR INPUTS
Oil Level / Temp
C30
AN S2 / Slave An02
UNI-POLAR INPUTS
—
C31
AN S3 / Slave An03
UNI-POLAR INPUTS
—
C32
AN S4 / Slave An04
UNI-POLAR INPUTS
—
C33
AN S5 / Slave An05
UNI-POLAR INPUTS
LowFuel Pressure
C34
AN S6 / Slave An06
UNI-POLAR INPUTS
Intake Flap Pos
Revision 2: Syvecs Audi TTRS RS3 Mk3 8V1 S7Plus Plug-in ECUSyvecs S7Plus general-purpose ECU shown as a family reference; vehicle-specific kit and adaptor may differ. Manufacturer photograph, reproduced with permission. Image source.
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Audi TTRS RS3 Mk3 8V1 S7Plus, with product code S7Plus-RS38V1. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs Audi TTRS RS3 Mk3 8V1 S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
From the Syvecs Audi RS3/TTRS 8V1 installation guide, revision 1.2. The tables list ECU-side positions and the manufacturer's kit notes, not complete original vehicle connector pinouts. The guide limits this schedule to CZGB engines. It describes B18 as LAM2HEATER in one column and Slave Out 10 in another; verify that conflicting assignment with Syvecs. A dash denotes an empty field in the manufacturer chart; confirm the exact loom and connector view.