Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
Syvecs Standalone ECUs
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None
Syvecs S7Plus general-purpose ECU
Syvecs S7Plus general-purpose ECU shown as a family reference; vehicle-specific kit and adaptor may differ. Manufacturer photograph, reproduced with permission. Image source.

Model and vehicle application

Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Audi TTRS RS3 Mk3 8V1 S7Plus, with product code S7Plus-RS38V1. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.

This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.

Wiring and pinout

Syvecs Audi TTRS RS3 Mk3 8V1 S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.

For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.

Calibration and service

Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.

Sources

Manufacturer ECU connector schedules

From the Syvecs Audi RS3/TTRS 8V1 installation guide, revision 1.2. The tables list ECU-side positions and the manufacturer's kit notes, not complete original vehicle connector pinouts. The guide limits this schedule to CZGB engines. It describes B18 as LAM2HEATER in one column and Slave Out 10 in another; verify that conflicting assignment with Syvecs. A dash denotes an empty field in the manufacturer chart; confirm the exact loom and connector view.

Connector A

PinSyvecs descriptionFunctionApplication notes
A1PWR CTR OUTMAIN RELAY OUTPUTMain Relay
A2H-Bridge1 / SlaveOut1H-Bridge1DBW +
A3H-Bridge2 / SlaveOut2H-Bridge2DBW -
A4H-Bridge3 / SlaveOut3H-Bridge3Tacho Wire
A5H-Bridge4 / SlaveOut4H-Bridge4Fan
A6H-Bridge5 / SlaveOut5H-Bridge5Valve for Oil Pressure Control
A7H-Bridge6 / SlaveOut6H-Bridge6Starter Relay
A8H-Bridge7 / SlaveOut7H-Bridge7Charcoal Solenoid
A9H-Bridge8 / SlaveOut8H-Bridge8Intake Fuel Pump
A10FUEL1INJECTOR or PWM OUTPUTPrimary Injector 1
A11FUEL2INJECTOR or PWM OUTPUTPrimary Injector 2
A12FUEL3INJECTOR or PWM OUTPUTPrimary Injector 3
A13FUEL4INJECTOR or PWM OUTPUTPrimary Injector 4
A14FUEL5INJECTOR or PWM OUTPUTPrimary Injector 5
A15FUEL6INJECTOR or PWM OUTPUTPort Injector 1 (External)
A16FUEL7INJECTOR or PWM OUTPUTPort Injector 2 (External)
A17FUEL8INJECTOR or PWM OUTPUTPort Injector 3 (External)
A18FUEL9INJECTOR or PWM OUTPUTPort Injector 4 (External)
A19FUEL10INJECTOR or PWM OUTPUTPort Injector 5 (External)
A20FUEL11INJECTOR or PWM OUTPUTExhaust Flap
A21FUEL12INJECTOR or PWM OUTPUTBoost Solenoid
A22FUEL13INJECTOR or PWM OUTPUTTurbo Recirc (N249)
A23FUEL14INJECTOR or PWM OUTPUTIntake Flap Control Solenoid
A24FUEL15INJECTOR or PWM OUTPUTVVT1 Int (N205)
A25FUEL16INJECTOR or PWM OUTPUTVVT1 Ex (N316)
A26IGN1CYL 1 IGNITION OUTPUTIGN1 (N70)
A27IGN2CYL 2 IGNITION OUTPUTIGN2 (N127)
A28IGN3CYL 3 IGNITION OUTPUTIGN3 (N291)
A29IGN4CYL 4 IGNITION OUTPUTIGN4 (N292)
A30IGN5CYL 5 IGNITION OUTPUTIGN5 (N292)
A31IGN6CYL 6 IGNITION OUTPUTDI Pump Control
A32PWRGNDPOWER GROUNDPwrGnd
A33PWRGNDPOWER GROUNDPwrGNd
A34PWRGNDPOWER GROUNDPwrGNd

Connector B

PinSyvecs descriptionFunctionApplication notes
B1PWRGNDPOWER GROUNDPWRGROUND
B2CAN2L——
B3CAN2H——
B4KNOCKKNOCKKnock +
B5KNOCK 2KNOCK 2—
B6PVBATCONSTANT 12V—
B7IVBAT12v—
B8LAM1ALamv / LamD1+/ LamLun1Pin6 on LSU4.9 Connector
B9LAM1BLami / LamD1- /LamIP1Pin1 on LSU4.9 Connector
B10LAM1CLamLIA1Pin5 on LSU4.9 Connector
B11LAM1DLamGND / LamLVM1Pin2 on LSU4.9 Connector
B12LAM1HEATERLAMBDA HEATERPin3 on LSU4.9 Connector
B13IVBAT12 V—
B14LAM2ALamv / LamD1+/ LamLun1—
B15LAM2BLami / LamD1- /LamIP1—
B16LAM2CLamLIA1—
B17LAM2DLamGND / LamLVM1—
B18LAM2HEATERSlave Out 10—
B19IVBAT12 V—
B20KLINEKline—
B21RS232RXRS232RX—
B22RS232TXRS232TX—
B23LANRX-Cat5 Pin2—
B24LANRX+Cat5 Pin1—
B25LANTX-Cat5 Pin6—
B26LANTX+Cat5 Pin3—

Connector C

PinSyvecs descriptionFunctionApplication notes
C1KNOCKGNDKNOCKGNDKnock -
C2ANGNDSENSOR GND—
C3ANGNDSENSOR GND—
C4ANGNDSENSOR GND—
C55V OUT5V OUT—
C65V OUT5V OUT—
C75V OUT5V OUT—
C8CAN LCan LowPowertrain Can
C9CAN HCan HighPowertrain Can
C10AN01BI-POLAR INPUTSDi Pressure
C11AN02BI-POLAR INPUTSMapSensor
C12AN03BI-POLAR INPUTSCharge Pressure
C13AN04BI-POLAR INPUTSBrake
C14AN05UNI-POLAR INPUTS—
C15AN06UNI-POLAR INPUTSVVT1Ex Pos
C16AN07UNI-POLAR INPUTSCrank Sensor
C17AN08UNI-POLAR INPUTSStarter Request
C18AN09VOLT-INPUTSTPS1A
C19AN10VOLT-INPUTSTPS1B
C20AN11VOLT-INPUTSPPSA
C21AN12VOLT-INPUTSPPSB
C22AN13RESISTIVE INPUTS—
C23AN14RESISTIVE INPUTSIntake Air Temp
C24AN15RESISTIVE INPUTSCoolant Temp
C25AN16RESISTIVE INPUTSOil Pressure Sw
C26EGT1-EGT1 -—
C27EGT1+EGT1 +—
C28PWR CTR INMAIN RELAY INPUT SWKey On sig (15)
C29AN S1 / Slave An01UNI-POLAR INPUTSOil Level / Temp
C30AN S2 / Slave An02UNI-POLAR INPUTS—
C31AN S3 / Slave An03UNI-POLAR INPUTS—
C32AN S4 / Slave An04UNI-POLAR INPUTS—
C33AN S5 / Slave An05UNI-POLAR INPUTSLowFuel Pressure
C34AN S6 / Slave An06UNI-POLAR INPUTSIntake Flap Pos