Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
Engine ECU
Parent
MS3Pro PNP
Applies to
MS3Pro PNP
Tool groups
None
Manufacturers
None
AMP MSPNP-Pro Subaru WRX ECU
MSPNP-Pro SW0205 Subaru WRX version shown as a family illustration; this application has its own case and connector layout. Image: AMP Engine Management, reproduced with permission.

MSPNP-Pro E369395 is a vehicle-specific MS3Pro-based plug-in engine management ECU. The manufacturer’s model-specific installation guide lists the following application: 1993–1995 BMW E36 325i, 328i and M3 as listed in the manufacturer’s guide. Fitment depends on the original ECU connector, engine, harness and market; confirm the exact part number before installation.

Application and installation

Confirm the actual engine and ECU connector, as the guide lists several models across the date range. Plug-in does not mean every optional feature is prewired: follow the relevant guide for setup, sensors, jumpers, base tune and ignition-timing checks.

Pinout and documentation

AMP EFI E369395 vehicle-specific installation and connector documentation is the primary source for this model. Check the connector orientation, version and any configurable or optional functions before wiring. Diagrams may be shown as images in the guide; this page does not substitute a pin assignment from another MSPNP model.

See the manufacturer’s ECU documentation index and firmware and base-tune index. Initial maps require verification and tuning for the particular engine.

Rear options connectors by hardware version

These tables follow the AMP EFI application guide. The guide labels the 26- and 22-position tables V2 and separately illustrates a 20-position options connector. Identify the installed ECU and connector generation before wiring; these are rear options, not the complete original BMW main connector.

V2 connector 1 — 26 positions

PinFunctionDefault or notes
1ASpark out ACoil A, cylinder 1; logic-level smart coil
1BSpark out BCoil B, cylinder 5; logic-level smart coil
1CSpark out CCoil C, cylinder 3; logic-level smart coil
1DSpark out DCoil D, cylinder 6; logic-level smart coil
1ESpark out ECoil E, cylinder 2; logic-level smart coil
1FSpark out FCoil F, cylinder 4; logic-level smart coil
1GInjector out G—
1HInjector out H—
1IDigital in 2—
1JDigital in 3—
1KDigital in 12 V—
1LIATAftermarket IAT; disconnect OE IAT if used
1MDigital frequency in 1—
1NDigital frequency in 2—
1OAnalog in 1Assigned MAF; disconnect MAF to repurpose
1PAnalog in 2General-purpose analog input
1QAnalog in 3General-purpose analog input
1RAnalog in 4General-purpose analog input
1SAnalog in 5General-purpose analog input
1TAnalog in 6General-purpose analog input
1UAnalog in 7General-purpose analog input
1VAnalog in 8 / EGOWideband sensor input; can repurpose
1WCAN H120 ohm termination onboard
1XCAN L120 ohm termination onboard
1Y5 V VREF outSensor 5 V power, internally fused 0.25 A
1ZSensor ground—

V2 connector 2 — 22 positions

PinFunctionDefault or notes
2A12 V+ outIgnition-switched; 0.25 A fuse; relay control only, not supply power
2BDigital input 1 / FLEXAvailable flex sensor input
2CIAC1A—
2DIAC1B—
2EIAC2A—
2FIAC2B—
2GInjector out I—
2HInjector out J—
2ITach outFactory dashboard tachometer
2JHigh current out 1—
2KHigh current out 2—
2LHigh current out 3—
2MPWM out 2Idle valve; IAC close
2NPWM out 3VANOS camshaft control
2OPWM out 4—
2PPWM out 5—
2QUnused—
2RUnused—
2SUnused—
2TUnused—
2UUnused—
2VUnused—

20-position options connector

PinFunctionDefault or notes
1High current 1—
2High current 2—
3High current 3—
4Injector GHigh impedance only
5Injector HHigh impedance only
6CMP+Hall only; internal pull-up to 5 V
7Vref +5 V—
8External MAPMove internal jumper
9Analog input 1MAF
10EGO—
11Digital input 4—
12Digital input 2—
13Digital input 1—
14CANL—
15CANH—
16DFIN3Wheel speed 2, VR+ only
17DFIN2Wheel speed 1, VR+ only
18Analog input 2—
19IAT—
20Sensor return—

The V2 source marks pins 1A–1F, 1W–1Z, 2A–2B and 2S–2V large and the remainder small. Check the original for views, electrical limits and jumper settings.