Vi-PEC V Series Nissan S14-S15 GTIR is a V Series plug-in ECU documented for Nissan S14–S15 SR20 and GTI-R short-header applications listed by Link. It is a vehicle-specific replacement board, and the precise model year, engine, ECU connector and market variant must be checked against the installation guide. Link's Vi-PEC manual index.
Installation and pin functions
Use the specific Vi-PEC installation manual for this application. Its installation instructions and pin-function sections identify connections and application differences; a similarly named V Series plug-in board for another vehicle must not be used as a wiring reference. Check the original ECU part number and wiring before fitting.
Programming and support
Link lists Vi-PEC Tuning Software (VTS) for the V Series. Firmware compatibility and the calibration depend on the ECU version. Consult the software archive and retain the original calibration before any change.
Identification limits
This page is indexed by the documented application rather than an independently verified manufacturer SKU. Check the manual for exact compatibility and do not infer additional vehicle fitments.
Manufacturer pinout tables
These are the positions documented in the Vi-PEC Nissan SR short-header installation guide, pages 22–23, looking into the ECU from the wire side. Positions absent from the guide are not assumed unused. The manufacturer gives separate 1991–93 S13 and 1994–2002 S13 Type-X/S14/S15 schedules; verify the loom, engine and exact model before fitting. The later schedule lists Aux 1 at both pins 9 and 10.
V1.2 lower-board issue: The guide identifies an incorrect tacho and ignition 1/2 connection when that board is used with 1991–93 SR20DET vehicles. It specifies jumper changes and a swap of header wires 2 and 3; consult its page 24 and the supplier before installation.
1994–2002 S13 Type-X, S14 and S15
| Position | ECU function |
|---|---|
| 101 | Injector 1 |
| 20 | An Volt 2 |
| 102 | Aux 6 |
| 24 | Aux 4 |
| 103 | Injector 3 |
| 25 | Ignition 4 / Aux – Ign 4 |
| 104 | Aux 5 |
| 32 | DI 5 |
| 105 | Aux – Inj 5 |
| 34 | DI 2 |
| 106 | Aux – Inj 6 |
| 35 | DI 4 |
| 110 | Injector 2 |
| 41 | DI 1 |
| 111 | Aux 7 |
| 43 | DI 3 |
| 39 | Ground |
| 38 | +14V ECCS Relay |
| 112 | Injector 4 |
| 113 | Aux – Inj 7 |
| 114 | Aux 8 |
| 115 | Aux – Inj 8 |
| 1 | Ignition 1 |
| 2 | Aux 2 |
| 3 | Ignition 2 / Aux – Ign 2 |
| 5 | Ignition 3 / Aux – Ign 3 |
| 9 | Aux 1 |
| 10 | Aux 1 |
| 11 | Aux 3 |
| 15 | An Temp 2 |
| 16 | An Volt 4 |
| 18 | An Temp 1 |
| 19 | An Volt 1 |
| 31, 40 | Trig 1 |
| 22, 30 | Trig 2 |
1991–1993 S13
| Position | ECU function |
|---|---|
| 101 | Injector 1 |
| 20 | An Volt 2 |
| 102 | Aux 6 |
| 24 | Aux 4 |
| 103 | Injector 3 |
| 25 | Aux 1 |
| 104 | Aux 5 |
| 32 | DI 5 |
| 105 | Aux – Inj 5 |
| 34 | DI 2 |
| 106 | Aux – Inj 6 |
| 35 | DI 4 |
| 110 | Injector 2 |
| 41 | DI 1 |
| 111 | Aux 7 |
| 43 | DI 3 |
| 39 | Ground |
| 38 | +14V ECCS Relay |
| 112 | Injector 4 |
| 113 | Aux – Inj 7 |
| 114 | Aux 8 |
| 115 | Aux – Inj 8 |
| 1 | Aux 2 |
| 2 | Ignition 1 |
| 3 | Ignition 2 / Aux – Ign 2 |
| 8 | Ignition 3 / Aux – Ign 3 |
| 9 | Ignition 4 / Aux – Ign 4 |
| 11 | Aux 3 |
| 15 | An Temp 2 |
| 16 | An Volt 4 |
| 18 | An Temp 1 |
| 19 | An Volt 1 |
| 31, 40 | Trig 1 |
| 22, 30 | Trig 2 |
Expansion connector and internal MAP
| Position | ECU function |
|---|---|
| Internal MAP | An Volt 3 |
| Expansion 1 | Signal Ground |
| Expansion 2 | +5V Out |
| Expansion 3 | DI 6 |
| Expansion 4 | - |
| Expansion 5 | An Volt 5 |
| Expansion 6 | An Volt 6 |
| Expansion 7 | An Temp 3 |
| Expansion 8 | - |