Removed text is struck through; added text is highlighted.
Vi-PEC iSupra i-Series plug-in ECU shown as a family illustration; this V-Series model's board, enclosure and vehicle connectors differ. Image: Link Engine Management Vi-PEC product archive, reproduced with permission.
Vi-PEC V Series Toyota ST185 is a V Series plug-in ECU documented for Toyota MR2 and Celica ST185 applications as listed by Link. It is a vehicle-specific replacement board, and the precise model year, engine, ECU connector and market variant must be checked against the installation guide. Link's Vi-PEC manual index.
Installation and pin functions
Use the specific Vi-PEC installation manual for this application. Its installation instructions and pin-function sections identify connections and application differences; a similarly named V Series plug-in board for another vehicle must not be used as a wiring reference. Check the original ECU part number and wiring before fitting.
Programming and support
Link lists Vi-PEC Tuning Software (VTS) for the V Series. Firmware compatibility and the calibration depend on the ECU version. Consult the software archive and retain the original calibration before any change.
Identification limits
This page is indexed by the documented application rather than an independently verified manufacturer SKU. Check the manual for exact compatibility and do not infer additional vehicle fitments.
Manufacturer pinout tables
All positions listed in the application-specific Vi-PEC installation guide, page 19, appear below. The guide specifies the view looking into the ECU from the wire side. It does not list every factory connector cavity; omitted positions are not assumed unused. The guide lists this schedule for Celica ST185 and MR2 Rev1. It lists An Volt 4 at pins 34 and 37 and marks expansion position 4 with an unexplained asterisk; check the actual board and harness.
Open each version to inspect formatting, tables and photographs.
Revision 2: Vi-PEC V Series Toyota ST185
Vi-PEC V Series Toyota ST185 is a V Series plug-in ECU documented for Toyota MR2 and Celica ST185 applications as listed by Link. It is a vehicle-specific replacement board, and the precise model year, engine, ECU connector and market variant must be checked against the installation guide. Link's Vi-PEC manual index.
Installation and pin functions
Use the specific Vi-PEC installation manual for this application. Its installation instructions and pin-function sections identify connections and application differences; a similarly named V Series plug-in board for another vehicle must not be used as a wiring reference. Check the original ECU part number and wiring before fitting.
Programming and support
Link lists Vi-PEC Tuning Software (VTS) for the V Series. Firmware compatibility and the calibration depend on the ECU version. Consult the software archive and retain the original calibration before any change.
Identification limits
This page is indexed by the documented application rather than an independently verified manufacturer SKU. Check the manual for exact compatibility and do not infer additional vehicle fitments.
Manufacturer pinout tables
All positions listed in the application-specific Vi-PEC installation guide, page 19, appear below. The guide specifies the view looking into the ECU from the wire side. It does not list every factory connector cavity; omitted positions are not assumed unused. The guide lists this schedule for Celica ST185 and MR2 Rev1. It lists An Volt 4 at pins 34 and 37 and marks expansion position 4 with an unexplained asterisk; check the actual board and harness.
Main ECU connector: documented positions
Position
ECU function
2
Injection 1
51
DI1
3
Injection 2
52
DI2
5
Aux 1
53
DI3
6
Aux - Inj 6
56
Aux 4
8
Aux 3
57
Aux 8
13
Trigger 1
63
Aux 6
15
Injection 3
71
+14V
16
Injection 4
46
Ground
17
Aux - Inj 5
34
AnVolt 4
18
Aux 2
20
Ign 1
22
Aux 5
23
Aux 7
25
Trigger 2
33
AnVolt 1
35
AnTemp 1
36
AnTemp 2
37
AnVolt 4
38
+5V
42
AnVolt 3
44
AnVolt 2
45
AnTemp 3
Other connections
Position
ECU function
Expansion 1
DI4
Expansion 2
DI5
Expansion 3
DI6
Expansion 4
AnVolt 4*
Expansion 5
AnVolt 5
Expansion 6
AnVolt 6
Revision 3: Vi-PEC V Series Toyota ST185Vi-PEC iSupra i-Series plug-in ECU shown as a family illustration; this V-Series model's board, enclosure and vehicle connectors differ. Image: Link Engine Management Vi-PEC product archive, reproduced with permission.
Vi-PEC V Series Toyota ST185 is a V Series plug-in ECU documented for Toyota MR2 and Celica ST185 applications as listed by Link. It is a vehicle-specific replacement board, and the precise model year, engine, ECU connector and market variant must be checked against the installation guide. Link's Vi-PEC manual index.
Installation and pin functions
Use the specific Vi-PEC installation manual for this application. Its installation instructions and pin-function sections identify connections and application differences; a similarly named V Series plug-in board for another vehicle must not be used as a wiring reference. Check the original ECU part number and wiring before fitting.
Programming and support
Link lists Vi-PEC Tuning Software (VTS) for the V Series. Firmware compatibility and the calibration depend on the ECU version. Consult the software archive and retain the original calibration before any change.
Identification limits
This page is indexed by the documented application rather than an independently verified manufacturer SKU. Check the manual for exact compatibility and do not infer additional vehicle fitments.
Manufacturer pinout tables
All positions listed in the application-specific Vi-PEC installation guide, page 19, appear below. The guide specifies the view looking into the ECU from the wire side. It does not list every factory connector cavity; omitted positions are not assumed unused. The guide lists this schedule for Celica ST185 and MR2 Rev1. It lists An Volt 4 at pins 34 and 37 and marks expansion position 4 with an unexplained asterisk; check the actual board and harness.