
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Porsche 991.2 Turbo S7Plus, with product code S7Plus-P991.2. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs Porsche 991.2 Turbo S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
Sources
- Syvecs Porsche 991.2 Turbo S7Plus product listing and application
- Manufacturer kit installation and pinout manual
- Syvecs plug-in kit support index
Manufacturer ECU connector schedules
From the Syvecs Porsche 991.2 kit guide. These are ECU-side connections and application notes, not complete factory vehicle connector tables. The manufacturer lists different B2 and B3 functions on the 991.1 and 991.2 charts; confirm the model and ECU before wiring. A dash is a blank field in the source.
Connector A
| ECU pin | Syvecs description | Function | Kit notes |
|---|---|---|---|
| A1 | PWR CTR OUT | MAIN RELAY OUTPUT | Main Relay |
| A2 | H-Bridge1 / SlaveOut1 | H-Bridge1 | DBW |
| A3 | H-Bridge2 / SlaveOut2 | H-Bridge2 | DBW |
| A4 | H-Bridge3 / SlaveOut3 | H-Bridge3 | ThermoStat |
| A5 | H-Bridge4 / SlaveOut4 | H-Bridge4 | Oil Pump LS |
| A6 | H-Bridge5 / SlaveOut5 | H-Bridge5 | Di Pump |
| A7 | H-Bridge6 / SlaveOut6 | H-Bridge6 | Rad Fans |
| A8 | H-Bridge7 / SlaveOut7 | H-Bridge7 | Valve Lift |
| A9 | H-Bridge8 / SlaveOut8 | H-Bridge8 | Starter Motor Relay |
| A10 | FUEL1 | INJECTOR or PWM OUTPUT | Primary Injector 1 |
| A11 | FUEL2 | INJECTOR or PWM OUTPUT | Primary Injector 2 |
| A12 | FUEL3 | INJECTOR or PWM OUTPUT | Primary Injector 3 |
| A13 | FUEL4 | INJECTOR or PWM OUTPUT | Primary Injector 4 |
| A14 | FUEL5 | INJECTOR or PWM OUTPUT | Primary Injector 5 |
| A15 | FUEL6 | INJECTOR or PWM OUTPUT | Primary Injector 6 |
| A16 | FUEL7 | INJECTOR or PWM OUTPUT | Secondary Injector 1 / Boost Pressure Adjuster 1 |
| A17 | FUEL8 | INJECTOR or PWM OUTPUT | Secondary Injector 2 / Boost Pressure Adjuster 2 |
| A18 | PWM1 /*FUEL9 | PWM OUTPUT | Secondary Injector 3 / Fuel Pump2 on 997.2 |
| A19 | PWM2 / *FUEL10 | PWM OUTPUT | Secondary Injector 4 / exhaust flap on 991.2 |
| A20 | PWM3 / *FUEL11 | PWM OUTPUT | Secondary Injector 5 / Tank Vent |
| A21 | PWM4 / *FUEL12 | PWM OUTPUT | Secondary Injector 6 / Engine Bay Fan |
| A22 | PWM5 | PWM OUTPUT | Divertor Valve |
| A23 | PWM6 | PWM OUTPUT | Fuel Pump Low pressure on 991 |
| A24 | PWM7 | PWM OUTPUT | VVT1 |
| A25 | PWM8 | PWM OUTPUT | VVT2 |
| A26 | IGN1 | CYL 1 IGNITION OUTPUT | — |
| A27 | IGN2 | CYL 2 IGNITION OUTPUT | — |
| A28 | IGN3 | CYL 3 IGNITION OUTPUT | — |
| A29 | IGN4 | CYL 4 IGNITION OUTPUT | — |
| A30 | IGN5 | CYL 5 IGNITION OUTPUT | — |
| A31 | IGN6 | CYL 6 IGNITION OUTPUT | — |
| A32 | PWRGND | POWER GROUND | — |
| A33 | PWRGND | POWER GROUND | Ground |
| A34 | PWRGND | POWER GROUND | Throttle Valve Ground |
Connector B
| ECU pin | Syvecs description | Function | Kit notes |
|---|---|---|---|
| B1 | PWRGND | POWER GROUND | — |
| B2 | EGT2 + | K - TYPE THERMO | — |
| B3 | EGT2 - | K - TYPE THERMO | — |
| B4 | KNOCK | KNOCK | — |
| B5 | KNOCK 2 | KNOCK 2 | — |
| B6 | PVBAT | — | — |
| B7 | IVBAT | — | — |
| B8 | LAM1A | Lamv / LamD1+/ LamLun1 | Pin6 on LSU4.9 Connector |
| B9 | LAM1B | Lami / LamD1- /LamIP1 | Pin1 on LSU4.9 Connector |
| B10 | LAM1C | LamLIA1 | Pin5 on LSU4.9 Connector |
| B11 | LAM1D | LamGND / LamLVM1 | Pin2 on LSU4.9 Connector |
| B12 | LAM1HEATER | LAMBDA HEATER | Pin3 on LSU4.9 Connector |
| B13 | IVBAT | — | — |
| B14 | LAM2A | Lamv / LamD1+/ LamLun1 | Pin6 on LSU4.9 Connector |
| B15 | LAM2B | Lami / LamD1- /LamIP1 | Pin1 on LSU4.9 Connector |
| B16 | LAM2C | LamLIA1 | Pin5 on LSU4.9 Connector |
| B17 | LAM2D | LamGND / LamLVM1 | Pin2 on LSU4.9 Connector |
| B18 | LAM2HEATER | LAMBDA HEATER | Pin3 on LSU4.9 Connector |
| B19 | IVBAT | — | — |
| B20 | KLINE | Kline | — |
| B21 | RS232RX | RS232RX | SET AS CAN L FOR TB with CAN BRIDGE |
| B22 | RS232TX | RS232TX | SET AS CAN H FOR TB with CAN BRIDGE |
| B23 | LANRX- | Cat5 Pin2 | — |
| B24 | LANRX+ | Cat5 Pin1 | — |
| B25 | LANTX- | Cat5 Pin6 | — |
| B26 | LANTX+ | Cat5 Pin3 | — |
Connector C
| ECU pin | Syvecs description | Function | Kit notes |
|---|---|---|---|
| C1 | KNOCKGND | KNOCKGND | — |
| C2 | ANGND | SENSOR GND | — |
| C3 | ANGND | SENSOR GND | — |
| C4 | ANGND | SENSOR GND | Maybe Sensor Ground as Labelled - |
| C5 | 5V OUT | 5V OUT | — |
| C6 | 5V OUT | 5V OUT | — |
| C7 | 5V OUT | 5V OUT | — |
| C8 | CAN L | Can Low | — |
| C9 | CAN H | Can High | — |
| C10 | AN01 | BI-POLAR INPUTS | Crank Sensor |
| C11 | AN02 | BI-POLAR INPUTS | VVt1IN |
| C12 | AN03 | BI-POLAR INPUTS | VVT2IN |
| C13 | AN04 | BI-POLAR INPUTS | — |
| C14 | AN05 | UNI-POLAR INPUTS | Pre Throttle Pressure |
| C15 | AN06 | UNI-POLAR INPUTS | — |
| C16 | AN07 | UNI-POLAR INPUTS | PPS2 |
| C17 | AN08 | UNI-POLAR INPUTS | PPS1 |
| C18 | AN09 | VOLT-INPUTS | DI Pressure |
| C19 | AN10 | VOLT-INPUTS | Engine Oil Pressure |
| C20 | AN11 | VOLT-INPUTS | TPS1A |
| C21 | AN12 | VOLT-INPUTS | TPS1B |
| C22 | AN13 | RESISTIVE INPUTS | — |
| C23 | AN14 | RESISTIVE INPUTS | Coolant temp |
| C24 | AN15 | RESISTIVE INPUTS | Brake |
| C25 | AN16 | RESISTIVE INPUTS | Clutch |
| C26 | EGT1- | EGT1 - | — |
| C27 | EGT1+ | EGT1 + | — |
| C28 | PWR CTR IN | MAIN RELAY INPUT SW | 12v Ignition |
| C29 | AN S1 / Slave An01 | UNI-POLAR INPUTS | — |
| C30 | AN S2 / Slave An02 | UNI-POLAR INPUTS | BSD Air Temp |
| C31 | AN S3 / Slave An03 | UNI-POLAR INPUTS | BSD Map Sensor |
| C32 | AN S4 / Slave An04 | UNI-POLAR INPUTS | Engine Comp Temp |
| C33 | AN S5 / Slave An05 | UNI-POLAR INPUTS | Oil Temp |
| C34 | AN S6 / Slave An06 | UNI-POLAR INPUTS | Oil Level |