Removed text is struck through; added text is highlighted.
Syvecs S7Plus general-purpose ECU shown as a family reference; vehicle-specific kit and adaptor may differ. Manufacturer photograph, reproduced with permission. Image source.
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Porsche 991.1 Turbo S7Plus, with product code S7Plus-P991.1. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs Porsche 991.1 Turbo S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
Sources
Syvecs Porsche 991.1 Turbo S7Plus product listing and applicationManufacturer kit installation and pinout manualSyvecs plug-in kit support index
Manufacturer ECU connector schedules
From the Syvecs Porsche 991.1 Turbo kit guide. These are ECU-side connections and application notes, not complete factory vehicle connector tables. The manufacturer lists different B2 and B3 functions on the 991.1 and 991.2 charts; confirm the model and ECU before wiring. A dash is a blank field in the source.
Connector A
ECU pinSyvecs descriptionFunctionKit notesA1PWR CTR OUTMAIN RELAY OUTPUT—A2H-Bridge1 / SlaveOut1H-Bridge1DBWA3H-Bridge2 / SlaveOut2H-Bridge2DBWA4H-Bridge3 / SlaveOut3H-Bridge3ThermoStatA5H-Bridge4 / SlaveOut4H-Bridge4Oil Pump ControlA6H-Bridge5 / SlaveOut5H-Bridge5Di PumpA7H-Bridge6 / SlaveOut6H-Bridge6Rad FansA8H-Bridge7 / SlaveOut7H-Bridge7Valve LiftA9H-Bridge8 / SlaveOut8H-Bridge8Starter Motor RelayA10FUEL1INJECTOR or PWM OUTPUTPrimary Injector 1A11FUEL2INJECTOR or PWM OUTPUTPrimary Injector 2A12FUEL3INJECTOR or PWM OUTPUTPrimary Injector 3A13FUEL4INJECTOR or PWM OUTPUTPrimary Injector 4A14FUEL5INJECTOR or PWM OUTPUTPrimary Injector 5A15FUEL6INJECTOR or PWM OUTPUTPrimary Injector 6A16FUEL7INJECTOR or PWM OUTPUTSecondary Injector 1 / Boost Pressure Adjuster 1A17FUEL8INJECTOR or PWM OUTPUTSecondary Injector 2 / Boost Pressure Adjuster 2A18FUEL9INJECTOR or PWM OUTPUTSecondary Injector 3 / Fuel Pump2 on 997.2A19FUEL10INJECTOR or PWM OUTPUTSecondary Injector 4 / Fuel pump1 on 997.2A20FUEL11INJECTOR or PWM OUTPUTSecondary Injector 5 / Tank VentA21FUEL12INJECTOR or PWM OUTPUTSecondary Injector 6 / Engine Bay FanA22FUEL13INJECTOR or PWM OUTPUTDivertor ValveA23FUEL14INJECTOR or PWM OUTPUTFuel Pump Low pressure on 991A24FUEL15INJECTOR or PWM OUTPUTVVT1A25FUEL16INJECTOR or PWM OUTPUTVVT2A26IGN1CYL 1 IGNITION OUTPUT—A27IGN2CYL 2 IGNITION OUTPUT—A28IGN3CYL 3 IGNITION OUTPUT—A29IGN4CYL 4 IGNITION OUTPUT—A30IGN5CYL 5 IGNITION OUTPUT—A31IGN6CYL 6 IGNITION OUTPUT—A32PWRGNDPOWER GROUND—A33PWRGNDPOWER GROUNDGroundA34PWRGNDPOWER GROUND—
Connector B
ECU pinSyvecs descriptionFunctionKit notesB1PWRGNDPOWER GROUND—B2CAN2L——B3CAN2H——B4KNOCKKNOCK—B5KNOCK 2KNOCK 2—B6PVBATCONSTANT 12V—B7IVBAT12v—B8LAM1ALamv / LamD1+/ LamLun1Pin6 on LSU4.9 ConnectorB9LAM1BLami / LamD1- /LamIP1Pin1 on LSU4.9 ConnectorB10LAM1CLamLIA1Pin5 on LSU4.9 ConnectorB11LAM1DLamGND / LamLVM1Pin2 on LSU4.9 ConnectorB12LAM1HEATERLAMBDA HEATERPin3 on LSU4.9 ConnectorB13IVBAT12V—B14LAM2ALamv / LamD1+/ LamLun1Pin6 on LSU4.9 ConnectorB15LAM2BLami / LamD1- /LamIP1Pin1 on LSU4.9 ConnectorB16LAM2CLamLIA1Pin5 on LSU4.9 ConnectorB17LAM2DLamGND / LamLVM1Pin2 on LSU4.9 ConnectorB18LAM2HEATERLAMBDA HEATERPin3 on LSU4.9 ConnectorB19IVBAT12VOil Pressure 12vB20KLINEKline—B21RS232RXRS232RXSET AS CAN L FOR TB with CAN BRIDGEB22RS232TXRS232TXSET AS CAN H FOR TB with CAN BRIDGEB23LANRX-Cat5 Pin2—B24LANRX+Cat5 Pin1—B25LANTX-Cat5 Pin6—B26LANTX+Cat5 Pin3—
Open each version to inspect formatting, tables and photographs.
Revision 2: Syvecs Porsche 991.1 Turbo S7Plus Plug-in ECUSyvecs S7Plus general-purpose ECU shown as a family reference; vehicle-specific kit and adaptor may differ. Manufacturer photograph, reproduced with permission. Image source.
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Porsche 991.1 Turbo S7Plus, with product code S7Plus-P991.1. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs Porsche 991.1 Turbo S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
From the Syvecs Porsche 991.1 Turbo kit guide. These are ECU-side connections and application notes, not complete factory vehicle connector tables. The manufacturer lists different B2 and B3 functions on the 991.1 and 991.2 charts; confirm the model and ECU before wiring. A dash is a blank field in the source.
Connector A
ECU pin
Syvecs description
Function
Kit notes
A1
PWR CTR OUT
MAIN RELAY OUTPUT
—
A2
H-Bridge1 / SlaveOut1
H-Bridge1
DBW
A3
H-Bridge2 / SlaveOut2
H-Bridge2
DBW
A4
H-Bridge3 / SlaveOut3
H-Bridge3
ThermoStat
A5
H-Bridge4 / SlaveOut4
H-Bridge4
Oil Pump Control
A6
H-Bridge5 / SlaveOut5
H-Bridge5
Di Pump
A7
H-Bridge6 / SlaveOut6
H-Bridge6
Rad Fans
A8
H-Bridge7 / SlaveOut7
H-Bridge7
Valve Lift
A9
H-Bridge8 / SlaveOut8
H-Bridge8
Starter Motor Relay
A10
FUEL1
INJECTOR or PWM OUTPUT
Primary Injector 1
A11
FUEL2
INJECTOR or PWM OUTPUT
Primary Injector 2
A12
FUEL3
INJECTOR or PWM OUTPUT
Primary Injector 3
A13
FUEL4
INJECTOR or PWM OUTPUT
Primary Injector 4
A14
FUEL5
INJECTOR or PWM OUTPUT
Primary Injector 5
A15
FUEL6
INJECTOR or PWM OUTPUT
Primary Injector 6
A16
FUEL7
INJECTOR or PWM OUTPUT
Secondary Injector 1 / Boost Pressure Adjuster 1
A17
FUEL8
INJECTOR or PWM OUTPUT
Secondary Injector 2 / Boost Pressure Adjuster 2
A18
FUEL9
INJECTOR or PWM OUTPUT
Secondary Injector 3 / Fuel Pump2 on 997.2
A19
FUEL10
INJECTOR or PWM OUTPUT
Secondary Injector 4 / Fuel pump1 on 997.2
A20
FUEL11
INJECTOR or PWM OUTPUT
Secondary Injector 5 / Tank Vent
A21
FUEL12
INJECTOR or PWM OUTPUT
Secondary Injector 6 / Engine Bay Fan
A22
FUEL13
INJECTOR or PWM OUTPUT
Divertor Valve
A23
FUEL14
INJECTOR or PWM OUTPUT
Fuel Pump Low pressure on 991
A24
FUEL15
INJECTOR or PWM OUTPUT
VVT1
A25
FUEL16
INJECTOR or PWM OUTPUT
VVT2
A26
IGN1
CYL 1 IGNITION OUTPUT
—
A27
IGN2
CYL 2 IGNITION OUTPUT
—
A28
IGN3
CYL 3 IGNITION OUTPUT
—
A29
IGN4
CYL 4 IGNITION OUTPUT
—
A30
IGN5
CYL 5 IGNITION OUTPUT
—
A31
IGN6
CYL 6 IGNITION OUTPUT
—
A32
PWRGND
POWER GROUND
—
A33
PWRGND
POWER GROUND
Ground
A34
PWRGND
POWER GROUND
—
Connector B
ECU pin
Syvecs description
Function
Kit notes
B1
PWRGND
POWER GROUND
—
B2
CAN2L
—
—
B3
CAN2H
—
—
B4
KNOCK
KNOCK
—
B5
KNOCK 2
KNOCK 2
—
B6
PVBAT
CONSTANT 12V
—
B7
IVBAT
12v
—
B8
LAM1A
Lamv / LamD1+/ LamLun1
Pin6 on LSU4.9 Connector
B9
LAM1B
Lami / LamD1- /LamIP1
Pin1 on LSU4.9 Connector
B10
LAM1C
LamLIA1
Pin5 on LSU4.9 Connector
B11
LAM1D
LamGND / LamLVM1
Pin2 on LSU4.9 Connector
B12
LAM1HEATER
LAMBDA HEATER
Pin3 on LSU4.9 Connector
B13
IVBAT
12V
—
B14
LAM2A
Lamv / LamD1+/ LamLun1
Pin6 on LSU4.9 Connector
B15
LAM2B
Lami / LamD1- /LamIP1
Pin1 on LSU4.9 Connector
B16
LAM2C
LamLIA1
Pin5 on LSU4.9 Connector
B17
LAM2D
LamGND / LamLVM1
Pin2 on LSU4.9 Connector
B18
LAM2HEATER
LAMBDA HEATER
Pin3 on LSU4.9 Connector
B19
IVBAT
12V
Oil Pressure 12v
B20
KLINE
Kline
—
B21
RS232RX
RS232RX
SET AS CAN L FOR TB with CAN BRIDGE
B22
RS232TX
RS232TX
SET AS CAN H FOR TB with CAN BRIDGE
B23
LANRX-
Cat5 Pin2
—
B24
LANRX+
Cat5 Pin1
—
B25
LANTX-
Cat5 Pin6
—
B26
LANTX+
Cat5 Pin3
—
Connector C
ECU pin
Syvecs description
Function
Kit notes
C1
KNOCKGND
KNOCKGND
—
C2
ANGND
SENSOR GND
—
C3
ANGND
SENSOR GND
—
C4
ANGND
SENSOR GND
—
C5
5V OUT
5V OUT
—
C6
5V OUT
5V OUT
—
C7
5V OUT
5V OUT
—
C8
CAN L
Can Low
—
C9
CAN H
Can High
—
C10
AN01
BI-POLAR INPUTS
Crank Sensor
C11
AN02
BI-POLAR INPUTS
VVt1IN
C12
AN03
BI-POLAR INPUTS
VVT2IN
C13
AN04
BI-POLAR INPUTS
—
C14
AN05
UNI-POLAR INPUTS
Pre Throttle Pressure
C15
AN06
UNI-POLAR INPUTS
Map Sensor
C16
AN07
UNI-POLAR INPUTS
Oil Temp
C17
AN08
UNI-POLAR INPUTS
PPS1
C18
AN09
VOLT-INPUTS
DI Pressure
C19
AN10
VOLT-INPUTS
Engine Oil Pressure
C20
AN11
VOLT-INPUTS
TPS1A
C21
AN12
VOLT-INPUTS
TPS1B
C22
AN13
RESISTIVE INPUTS
Air temp
C23
AN14
RESISTIVE INPUTS
Coolant temp
C24
AN15
RESISTIVE INPUTS
Brake
C25
AN16
RESISTIVE INPUTS
Clutch
C26
EGT1-
EGT1 -
—
C27
EGT1+
EGT1 +
—
C28
PWR CTR IN
MAIN RELAY INPUT SW
12v Ignition
C29
AN S1 / Slave An01
UNI-POLAR INPUTS
EGT1
C30
AN S2 / Slave An02
UNI-POLAR INPUTS
EGT2
C31
AN S3 / Slave An03
UNI-POLAR INPUTS
Boost Feedback1
C32
AN S4 / Slave An04
UNI-POLAR INPUTS
Boost Feedback2
C33
AN S5 / Slave An05
UNI-POLAR INPUTS
PPS2
C34
AN S6 / Slave An06
UNI-POLAR INPUTS
Oil Level
Revision 2: Syvecs Porsche 991.1 Turbo S7Plus Plug-in ECUSyvecs S7Plus general-purpose ECU shown as a family reference; vehicle-specific kit and adaptor may differ. Manufacturer photograph, reproduced with permission. Image source.
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Porsche 991.1 Turbo S7Plus, with product code S7Plus-P991.1. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs Porsche 991.1 Turbo S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
From the Syvecs Porsche 991.1 Turbo kit guide. These are ECU-side connections and application notes, not complete factory vehicle connector tables. The manufacturer lists different B2 and B3 functions on the 991.1 and 991.2 charts; confirm the model and ECU before wiring. A dash is a blank field in the source.