Emissions testing equipment can tell a technician what is in a tailpipe sample, how much light a diesel smoke plume absorbs, or how emissions change through a controlled drive. The instruments measure different things; a low smoke-opacity result, a clean fault memory and a pass on a petrol gas analyser are not interchangeable evidence.
This guide covers the instruments, sampling, readings and UK MOT context. For the control systems themselves see petrol and diesel emissions; for an example equipment family see Bosch BEA emissions analysis.
Choose the measurement
| Instrument | Output and use | What it does not establish |
|---|---|---|
| Four-gas petrol exhaust analyser | CO and CO₂ in volume percent, hydrocarbons (HC) in ppm and O₂ in volume percent; calculates lambda from the sample. Used in diagnosis and, where approved, the relevant MOT gas test. | Calculated lambda is not the electrical output of the car's oxygen sensor; these channels do not measure NOx or particle number. |
| Five-gas analyser | Adds a NO or NOx channel depending on the instrument and configuration. | Do not assume every fifth channel reads total NOx or that a stationary measurement is a type-approval result. Check the model's specification and calibration. |
| Diesel smoke meter / opacimeter | Measures light absorption by a smoke sample; the result is a light-absorption coefficient, normally in m⁻¹. Used in the applicable MOT diesel smoke test. | It is not a count of individual particles, a particulate-mass measurement, or a NOx analyser. |
| Particle-number counter | Counts particles per unit volume within a specified particle-size range; certain instruments are designed for periodic inspections. | A concentration cannot be compared directly with a type-approval particles-per-kilometre result without the prescribed procedure. It does not replace the applicable UK MOT smoke test simply because it is available. |
| Scan tool, oscilloscope and pressure gauge | Provide fault codes, monitor readiness and live values, electrical waveforms or pressure for diagnosis. | A fault code is a monitored symptom and a clear code memory does not prove tailpipe compliance. |
| Chassis dynamometer and laboratory analysers | Measure emissions through a defined driving cycle with controlled sampling and distance or work measurement. | A static idle test does not reproduce the full cycle, load, cold start or distance-normalised result. |
| Portable emissions measurement system (PEMS) | Measures during use, combining exhaust analysis and exhaust flow with position, ambient and vehicle data. | Requires its own validation, calibration and test procedure; it is not a handheld replacement for an MOT analyser. |
The European Commission Joint Research Centre describes PEMS and its components. The DVSA inspection manual defines the actual in-service tests for cars and light commercial vehicles.
Four-gas analyser: sample path and channels
A pump draws exhaust through a tailpipe probe and hose to the analyser. Filters and a water separator protect the measuring components; their condition and the manufacturer's instructions matter. The unit needs to warm up, zero and pass its checks before a representative sample is taken. A leak in the sampling hose or exhaust can draw in air and dilute the sample. Residual fuel vapour left in a contaminated system can give an HC hang-up reading before the next test. The MOT full catalyst procedure calls for a hang-up check before sampling; follow the analyser prompts and current manual rather than using a generic sequence. DVSA, section 8.2.
- CO: a product of incomplete combustion. Elevated readings can accompany a rich mixture or poor catalyst conversion; temperature, mixture control and combustion must be considered.
- HC: unburned or partly burned fuel compounds, reported as ppm by the instrument. Misfire, incomplete combustion and catalyst condition can affect it. Different instruments and fuel calibrations do not necessarily respond identically to every hydrocarbon.
- CO₂: a principal combustion product. Consider it with the other channels and sampling condition; dilution can reduce the measured concentration.
- O₂: residual oxygen in the sample. High O₂ may reflect a lean mixture, a misfire that leaves oxygen unconsumed, or fresh air entering a leaky exhaust or sampling system.
- Lambda: calculated from exhaust concentrations using an appropriate fuel calculation. A value above 1 is interpreted as lean and below 1 as rich, but air leaks and misfire can mislead. It does not identify a faulty oxygen sensor by itself.
Many workshop analysers use non-dispersive infrared measurement for gases including CO, CO₂ and HC and a separate oxygen sensor. A fifth channel is model-dependent: check whether it measures NO or reports NOx. See Bosch's emissions analysis equipment literature and the Measuring Instruments Regulations 2016, schedule 1J for exhaust gas analyser characteristics and lambda calculation.
A pattern of high HC and O₂ is a reason to investigate combustion and leaks, not a verdict from the instrument alone. High CO with elevated HC can point to rich running or poor conversion, but confirm engine condition and sample integrity. A catalyst needs operating temperature and correct upstream combustion; comparing measured values under the specified conditions with fault data is more useful than replacing a catalyst on one reading.
Diesel smoke meter and particulate counter
An opacimeter passes light through exhaust and determines how much is absorbed or scattered. For the relevant UK MOT test it displays a light-absorption coefficient, not a direct count of particles. Probe alignment and the meter's setup vary by design. Before free acceleration the tester checks engine condition and operating temperature and follows the DVSA procedure and the smoke meter instructions. If the engine is unsafe, the manual requires the tester not to perform the smoke test. Limits, exemptions and procedure depend on the vehicle. The current manual excludes hybrids including mild hybrids from the opacity check and specifies how to enter plate values, including a tolerance adjustment. DVSA MOT manual, section 8.2.2.
A particle-number counter addresses a different question: how many particles fall within the measuring system's defined range in a volume of sample. The lower detectable size, conditioning, dilution and sampling procedure influence the result, so compare like with like. A clean-looking exhaust or a low opacity result does not prove that a filter is intact or that particle number is low. The DVSA DPF guidance discusses the limits of the smoke test and inspection of fitted filters. Equipment is discussed in Bosch BEA emissions analysis.
UK MOT equipment, calibration and records
For an official test, use equipment approved for the test and follow the current DVSA approved testing equipment list, the vehicle inspection manual, the equipment instructions and station requirements. A workshop diagnostic instrument may be useful without being approved for MOT use. Test selection, engine warm-up, speed, sample-taking, limits, vehicle age and exemptions are specified by the manual; the tester must not substitute a preferred method.
The DVSA testing guide, appendix 2, states that the user should check the gas analyser hose and probe for leaks daily. Calibration is at intervals of three, six or twelve months depending on make or type, by an appropriately recognised technician under the approved procedure, using certified calibration gas. The guide specifies weekly user checks for diesel smoke meters and calibration every twelve months by a UKAS-accredited technician. It also specifies exceptions and additional conditions for certain approved self-gassing analysers and initial certificates; consult the guide and the actual instrument documentation rather than assuming a single interval for every model.
A zero check, a leak check and calibration are different operations. Zeroing establishes an instrument reference; a leak check looks for sampling-system leakage; calibration checks and adjusts the instrument against known standards under the required procedure. Keep calibration certificates and required records available. Follow the maker's service guidance for probes, hoses, filters, water traps, oxygen sensors and any NO channel.
Workshop procedure and interpreting results
- Identify vehicle, engine, fuel and installed emissions equipment. Record the reported defect and distinguish an MOT test from diagnosis or research.
- Check the instrument's approval where required, calibration, warm-up and prescribed self-checks. Inspect the probe, hose, filter and water trap; check for HC hang-up or leaks as required.
- Check that the engine and exhaust are safe and in the condition prescribed for the test. Make sure the sample represents the exhaust; record operating temperature, speed and any applicable vehicle-specific limits.
- Run the specified test and retain the readings. Investigate a failure using gas channels or smoke together with fault codes, freeze-frame data, live sensor values, mechanical condition and known-good specifications.
- Repair the cause, then repeat the applicable test under the specified conditions. A reset or cleared warning lamp does not prove that a defect has been corrected.
For static engine running, use suitable tailpipe extraction to a safe outside location. Exhaust contains poisonous carbon monoxide; see the HSE guidance on vehicle exhaust. Exhaust and aftertreatment parts can become hot, especially during regeneration; use the vehicle and equipment manufacturers' precautions.
Laboratory and road testing
Type-approval testing uses prescribed test cycles, sampling and data reduction. Gas concentrations must be combined with flow and the test distance or work to calculate the required emissions rate; a tailpipe percentage at idle cannot simply be converted to mg/km. Laboratory systems can use, for example, infrared analysers for CO and CO₂, flame-ionisation analysers for hydrocarbons and chemiluminescence for nitrogen oxides. Particulate mass and number use their own sampling methods and specifications. The precise instruments and methods depend on the standard and application: EPA-approved California test methods provide one example, not a substitute for the applicable light-vehicle procedure.
On-road PEMS adds portable analysers and exhaust-flow measurement to position, ambient and vehicle information. The European Commission describes its role in real-world in-use testing. PEMS, the laboratory cycle and the MOT answer different questions and may not give directly comparable values.
Sources and further reading
- DVSA MOT inspection manual, section 8: test selection, equipment, procedures, conditions and defects.
- DVSA MOT testing guide, appendix 2: equipment checks, calibration and certificates.
- DVSA approved MOT testing equipment.
- Health and Safety Executive: vehicle exhaust emissions.
- European Commission Joint Research Centre: PEMS.
- Bosch BEA emissions analysis and petrol and diesel emissions on this wiki.