Removed text is struck through; added text is highlighted.
Syvecs S7Plus standalone ECU shown as a family illustration. This vehicle-specific kit and its adapter or wiring are not pictured and may differ. Image: Syvecs, reproduced with permission.
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Volkswagen Golf R32 Mk4 Mk5 S7Plus. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs Volkswagen Golf R32 Mk4 Mk5 S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
Sources
Syvecs Volkswagen Golf R32 Mk4 Mk5 S7Plus product listing and applicationManufacturer kit installation and pinout manualSyvecs plug-in kit support index
Manufacturer ECU connector schedules
From the Syvecs Volkswagen R32 Mk4/Mk5 installation guide, revision 1.2. The tables list ECU-side pins and the manufacturer's vehicle-specific notes, not the complete original vehicle connectors. A dash denotes a blank field in the source, not proof of an unused circuit. The manufacturer table does not show C10; its function is unverified and has not been inferred. Confirm the ECU, harness revision and connector orientation against the manufacturer document.
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Volkswagen Golf R32 Mk4 Mk5 S7Plus. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs Volkswagen Golf R32 Mk4 Mk5 S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
From the Syvecs Volkswagen R32 Mk4/Mk5 installation guide, revision 1.2. The tables list ECU-side pins and the manufacturer's vehicle-specific notes, not the complete original vehicle connectors. A dash denotes a blank field in the source, not proof of an unused circuit. The manufacturer table does not show C10; its function is unverified and has not been inferred. Confirm the ECU, harness revision and connector orientation against the manufacturer document.
Connector A
ECU pin
Syvecs description
Function
Application notes
A1
PWR CTR OUT
MAIN RELAY OUTPUT
Main Relay
A2
H-Bridge1 / SlaveOut1
H-Bridge1
DBW
A3
H-Bridge2 / SlaveOut2
H-Bridge2
DBW
A4
H-Bridge3 / SlaveOut3
H-Bridge3
—
A5
H-Bridge4 / SlaveOut4
H-Bridge4
—
A6
H-Bridge5 / SlaveOut5
H-Bridge5
—
A7
H-Bridge6 / SlaveOut6
H-Bridge6
—
A8
H-Bridge7 / SlaveOut7
H-Bridge7
—
A9
H-Bridge8 / SlaveOut8
H-Bridge8
—
A10
FUEL1
INJECTOR or PWM OUTPUT
Primary Injector 1
A11
FUEL2
INJECTOR or PWM OUTPUT
Primary Injector 2
A12
FUEL3
INJECTOR or PWM OUTPUT
Primary Injector 3
A13
FUEL4
INJECTOR or PWM OUTPUT
Primary Injector 4
A14
FUEL5
INJECTOR or PWM OUTPUT
Primary Injector 5
A15
FUEL6
INJECTOR or PWM OUTPUT
Primary Injector 6
A16
FUEL7
INJECTOR or PWM OUTPUT
—
A17
FUEL8
INJECTOR or PWM OUTPUT
—
A18
PWM1 /*FUEL9
PWM OUTPUT
Fuel Pump
A19
PWM2 / *FUEL10
PWM OUTPUT
FAN
A20
PWM3 / *FUEL11
PWM OUTPUT
Tacho
A21
PWM4 / *FUEL12
PWM OUTPUT
Intake Flap
A22
PWM5
PWM OUTPUT
—
A23
PWM6
PWM OUTPUT
—
A24
PWM7
PWM OUTPUT
VVT In
A25
PWM8
PWM OUTPUT
VVT Ex
A26
IGN1
CYL 1 IGNITION OUTPUT
CYL 1 IGNITION OUTPUT
A27
IGN2
CYL 2 IGNITION OUTPUT
CYL 2 IGNITION OUTPUT
A28
IGN3
CYL 3 IGNITION OUTPUT
CYL 3 IGNITION OUTPUT
A29
IGN4
CYL 4 IGNITION OUTPUT
CYL 4 IGNITION OUTPUT
A30
IGN5
CYL 5 IGNITION OUTPUT
CYL 5 IGNITION OUTPUT
A31
IGN6
CYL 6 IGNITION OUTPUT
CYL 6 IGNITION OUTPUT
A32
PWRGND
POWER GROUND
PwrGnd
A33
PWRGND
POWER GROUND
PwrGNd
A34
PWRGND
POWER GROUND
—
Connector B
ECU pin
Syvecs description
Function
Application notes
B1
PWRGND
POWER GROUND
—
B2
CAN2L
—
—
B3
CAN2H
—
—
B4
KNOCK
KNOCK
—
B5
KNOCK 2
KNOCK 2
—
B6
PVBAT
CONSTANT 12V
—
B7
IVBAT
12v
—
B8
LAM1A
Lamv / LamD1+/ LamLun1
LSU4.9 - PIN6
B9
LAM1B
Lami / LamD1- /LamIP1
LSU4.9 - PIN1
B10
LAM1C
LamLIA1
—
B11
LAM1D
LamGND / LamLVM1
LSU4.9 - PIN2
B12
LAM1HEATER
LAMBDA HEATER
LSU4.9 - PIN3
B13
IVBAT
12V
—
B14
LAM2A
Lamv / LamD1+/ LamLun1
—
B15
LAM2B
Lami / LamD1- /LamIP1
—
B16
LAM2C
LamLIA1
—
B17
LAM2D
LamGND / LamLVM1
—
B18
LAM2HEATER
LAMBDA HEATER
—
B19
IVBAT
12V
—
B20
KLINE
RS232RX
—
B21
RS232RX
RS232RX
—
B22
RS232TX
RS232TX
—
B23
LANRX-
Cat5 Pin2
—
B24
LANRX+
Cat5 Pin1
—
B25
LANTX-
Cat5 Pin6
—
B26
LANTX+
Cat5 Pin3
—
Connector C
ECU pin
Syvecs description
Function
Application notes
C1
KNOCK GROUND
KNOCK GROUND
—
C2
ANGND
SENSOR GND
—
C3
ANGND
SENSOR GND
Map Sensor Ground
C4
ANGND
SENSOR GND
—
C5
5V OUT
5V OUT
—
C6
5V OUT
5V OUT
Map Sensor 5v
C7
5V OUT
5V OUT
—
C8
CAN L
Can Low
—
C9
CAN H
Can High
—
C11
AN02
BI-POLAR INPUTS
Brake Sw
C12
AN03
BI-POLAR INPUTS
—
C13
AN04
BI-POLAR INPUTS
—
C14
AN05
UNI-POLAR INPUTS
PPS1
C15
AN06
UNI-POLAR INPUTS
—
C16
AN07
UNI-POLAR INPUTS
Inlet Cam
C17
AN08
UNI-POLAR INPUTS
Exh Cam
C18
AN09
VOLT-INPUTS
TPS1
C19
AN10
VOLT-INPUTS
Map Signal
C20
AN11
VOLT-INPUTS
Tps2
C21
AN12
VOLT-INPUTS
Clutch Sw
C22
AN13
RESISTIVE INPUTS
Water Temp
C23
AN14
RESISTIVE INPUTS
Air Temp
C24
AN15
RESISTIVE INPUTS
Cruise Sw
C25
AN16
RESISTIVE INPUTS
—
C26
EGT1-
EGT1 -
—
C27
EGT1+
EGT1 +
—
C28
PWR CTR IN
MAIN RELAY INPUT SW
Ignition Sw
C29
AN S1 / Slave An01
UNI-POLAR INPUTS
—
C30
AN S2 / Slave An02
UNI-POLAR INPUTS
—
C31
AN S3 / Slave An03
UNI-POLAR INPUTS
—
C32
AN S4 / Slave An04
UNI-POLAR INPUTS
—
C33
AN S5 / Slave An05
UNI-POLAR INPUTS
—
C34
AN S6 / Slave An06
UNI-POLAR INPUTS
—
Revision 3: Syvecs Volkswagen Golf R32 Mk4 Mk5 S7Plus Plug-in ECUSyvecs S7Plus standalone ECU shown as a family illustration. This vehicle-specific kit and its adapter or wiring are not pictured and may differ. Image: Syvecs, reproduced with permission.
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Volkswagen Golf R32 Mk4 Mk5 S7Plus. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs Volkswagen Golf R32 Mk4 Mk5 S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
From the Syvecs Volkswagen R32 Mk4/Mk5 installation guide, revision 1.2. The tables list ECU-side pins and the manufacturer's vehicle-specific notes, not the complete original vehicle connectors. A dash denotes a blank field in the source, not proof of an unused circuit. The manufacturer table does not show C10; its function is unverified and has not been inferred. Confirm the ECU, harness revision and connector orientation against the manufacturer document.