Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Volkswagen Golf R32 Mk4 Mk5 S7Plus. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs Volkswagen Golf R32 Mk4 Mk5 S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
Sources
- Syvecs Volkswagen Golf R32 Mk4 Mk5 S7Plus product listing and application
- Manufacturer kit installation and pinout manual
- Syvecs plug-in kit support index
Manufacturer ECU connector schedules
From the Syvecs Volkswagen R32 Mk4/Mk5 installation guide, revision 1.2. The tables list ECU-side pins and the manufacturer's vehicle-specific notes, not the complete original vehicle connectors. A dash denotes a blank field in the source, not proof of an unused circuit. The manufacturer table does not show C10; its function is unverified and has not been inferred. Confirm the ECU, harness revision and connector orientation against the manufacturer document.
Connector A
| ECU pin | Syvecs description | Function | Application notes |
|---|---|---|---|
| A1 | PWR CTR OUT | MAIN RELAY OUTPUT | Main Relay |
| A2 | H-Bridge1 / SlaveOut1 | H-Bridge1 | DBW |
| A3 | H-Bridge2 / SlaveOut2 | H-Bridge2 | DBW |
| A4 | H-Bridge3 / SlaveOut3 | H-Bridge3 | — |
| A5 | H-Bridge4 / SlaveOut4 | H-Bridge4 | — |
| A6 | H-Bridge5 / SlaveOut5 | H-Bridge5 | — |
| A7 | H-Bridge6 / SlaveOut6 | H-Bridge6 | — |
| A8 | H-Bridge7 / SlaveOut7 | H-Bridge7 | — |
| A9 | H-Bridge8 / SlaveOut8 | H-Bridge8 | — |
| A10 | FUEL1 | INJECTOR or PWM OUTPUT | Primary Injector 1 |
| A11 | FUEL2 | INJECTOR or PWM OUTPUT | Primary Injector 2 |
| A12 | FUEL3 | INJECTOR or PWM OUTPUT | Primary Injector 3 |
| A13 | FUEL4 | INJECTOR or PWM OUTPUT | Primary Injector 4 |
| A14 | FUEL5 | INJECTOR or PWM OUTPUT | Primary Injector 5 |
| A15 | FUEL6 | INJECTOR or PWM OUTPUT | Primary Injector 6 |
| A16 | FUEL7 | INJECTOR or PWM OUTPUT | — |
| A17 | FUEL8 | INJECTOR or PWM OUTPUT | — |
| A18 | PWM1 /*FUEL9 | PWM OUTPUT | Fuel Pump |
| A19 | PWM2 / *FUEL10 | PWM OUTPUT | FAN |
| A20 | PWM3 / *FUEL11 | PWM OUTPUT | Tacho |
| A21 | PWM4 / *FUEL12 | PWM OUTPUT | Intake Flap |
| A22 | PWM5 | PWM OUTPUT | — |
| A23 | PWM6 | PWM OUTPUT | — |
| A24 | PWM7 | PWM OUTPUT | VVT In |
| A25 | PWM8 | PWM OUTPUT | VVT Ex |
| A26 | IGN1 | CYL 1 IGNITION OUTPUT | CYL 1 IGNITION OUTPUT |
| A27 | IGN2 | CYL 2 IGNITION OUTPUT | CYL 2 IGNITION OUTPUT |
| A28 | IGN3 | CYL 3 IGNITION OUTPUT | CYL 3 IGNITION OUTPUT |
| A29 | IGN4 | CYL 4 IGNITION OUTPUT | CYL 4 IGNITION OUTPUT |
| A30 | IGN5 | CYL 5 IGNITION OUTPUT | CYL 5 IGNITION OUTPUT |
| A31 | IGN6 | CYL 6 IGNITION OUTPUT | CYL 6 IGNITION OUTPUT |
| A32 | PWRGND | POWER GROUND | PwrGnd |
| A33 | PWRGND | POWER GROUND | PwrGNd |
| A34 | PWRGND | POWER GROUND | — |
Connector B
| ECU pin | Syvecs description | Function | Application notes |
|---|---|---|---|
| B1 | PWRGND | POWER GROUND | — |
| B2 | CAN2L | — | — |
| B3 | CAN2H | — | — |
| B4 | KNOCK | KNOCK | — |
| B5 | KNOCK 2 | KNOCK 2 | — |
| B6 | PVBAT | CONSTANT 12V | — |
| B7 | IVBAT | 12v | — |
| B8 | LAM1A | Lamv / LamD1+/ LamLun1 | LSU4.9 - PIN6 |
| B9 | LAM1B | Lami / LamD1- /LamIP1 | LSU4.9 - PIN1 |
| B10 | LAM1C | LamLIA1 | — |
| B11 | LAM1D | LamGND / LamLVM1 | LSU4.9 - PIN2 |
| B12 | LAM1HEATER | LAMBDA HEATER | LSU4.9 - PIN3 |
| B13 | IVBAT | 12V | — |
| B14 | LAM2A | Lamv / LamD1+/ LamLun1 | — |
| B15 | LAM2B | Lami / LamD1- /LamIP1 | — |
| B16 | LAM2C | LamLIA1 | — |
| B17 | LAM2D | LamGND / LamLVM1 | — |
| B18 | LAM2HEATER | LAMBDA HEATER | — |
| B19 | IVBAT | 12V | — |
| B20 | KLINE | RS232RX | — |
| B21 | RS232RX | RS232RX | — |
| B22 | RS232TX | RS232TX | — |
| B23 | LANRX- | Cat5 Pin2 | — |
| B24 | LANRX+ | Cat5 Pin1 | — |
| B25 | LANTX- | Cat5 Pin6 | — |
| B26 | LANTX+ | Cat5 Pin3 | — |
Connector C
| ECU pin | Syvecs description | Function | Application notes |
|---|---|---|---|
| C1 | KNOCK GROUND | KNOCK GROUND | — |
| C2 | ANGND | SENSOR GND | — |
| C3 | ANGND | SENSOR GND | Map Sensor Ground |
| C4 | ANGND | SENSOR GND | — |
| C5 | 5V OUT | 5V OUT | — |
| C6 | 5V OUT | 5V OUT | Map Sensor 5v |
| C7 | 5V OUT | 5V OUT | — |
| C8 | CAN L | Can Low | — |
| C9 | CAN H | Can High | — |
| C11 | AN02 | BI-POLAR INPUTS | Brake Sw |
| C12 | AN03 | BI-POLAR INPUTS | — |
| C13 | AN04 | BI-POLAR INPUTS | — |
| C14 | AN05 | UNI-POLAR INPUTS | PPS1 |
| C15 | AN06 | UNI-POLAR INPUTS | — |
| C16 | AN07 | UNI-POLAR INPUTS | Inlet Cam |
| C17 | AN08 | UNI-POLAR INPUTS | Exh Cam |
| C18 | AN09 | VOLT-INPUTS | TPS1 |
| C19 | AN10 | VOLT-INPUTS | Map Signal |
| C20 | AN11 | VOLT-INPUTS | Tps2 |
| C21 | AN12 | VOLT-INPUTS | Clutch Sw |
| C22 | AN13 | RESISTIVE INPUTS | Water Temp |
| C23 | AN14 | RESISTIVE INPUTS | Air Temp |
| C24 | AN15 | RESISTIVE INPUTS | Cruise Sw |
| C25 | AN16 | RESISTIVE INPUTS | — |
| C26 | EGT1- | EGT1 - | — |
| C27 | EGT1+ | EGT1 + | — |
| C28 | PWR CTR IN | MAIN RELAY INPUT SW | Ignition Sw |
| C29 | AN S1 / Slave An01 | UNI-POLAR INPUTS | — |
| C30 | AN S2 / Slave An02 | UNI-POLAR INPUTS | — |
| C31 | AN S3 / Slave An03 | UNI-POLAR INPUTS | — |
| C32 | AN S4 / Slave An04 | UNI-POLAR INPUTS | — |
| C33 | AN S5 / Slave An05 | UNI-POLAR INPUTS | — |
| C34 | AN S6 / Slave An06 | UNI-POLAR INPUTS | — |