Removed text is struck through; added text is highlighted.
Syvecs S7Plus general-purpose ECU shown as a family reference; vehicle-specific kit and adaptor may differ. Manufacturer photograph, reproduced with permission. Image source.
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Mitsubishi Evo X Manual SST S7Plus, with product code S7Plus-EVOX. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs Mitsubishi Evo X Manual SST S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
Sources
Syvecs Mitsubishi Evo X Manual SST S7Plus product listing and applicationManufacturer kit installation and pinout manualSyvecs plug-in kit support index
Manufacturer ECU connector schedules
From the Syvecs Mitsubishi Evo X installation guide, revision 1.2. The tables list ECU-side pins and the manufacturer's vehicle-specific notes, not the complete original vehicle connectors. A dash denotes a blank field in the source, not proof of an unused circuit. Confirm the ECU, harness revision and connector orientation against the manufacturer document.
Open each version to inspect formatting, tables and photographs.
Revision 2: Syvecs Mitsubishi Evo X Manual SST S7Plus Plug-in ECUSyvecs S7Plus general-purpose ECU shown as a family reference; vehicle-specific kit and adaptor may differ. Manufacturer photograph, reproduced with permission. Image source.
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Mitsubishi Evo X Manual SST S7Plus, with product code S7Plus-EVOX. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs Mitsubishi Evo X Manual SST S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
From the Syvecs Mitsubishi Evo X installation guide, revision 1.2. The tables list ECU-side pins and the manufacturer's vehicle-specific notes, not the complete original vehicle connectors. A dash denotes a blank field in the source, not proof of an unused circuit. Confirm the ECU, harness revision and connector orientation against the manufacturer document.
Connector A
ECU pin
Syvecs description
Function
Application notes
A1
PWR CTR OUT
MAIN RELAY OUTPUT
Main Relay
A2
H‐Bridge1 / SlaveOut1
H‐Bridge1
DBW+
A3
H‐Bridge2 / SlaveOut2
H‐Bridge2
DBW‐
A4
H‐Bridge3 / SlaveOut3
H‐Bridge3
—
A5
H‐Bridge4 / SlaveOut4
H‐Bridge4
—
A6
H‐Bridge5 / SlaveOut5
H‐Bridge5
Evap Solenoid
A7
H‐Bridge6 / SlaveOut6
H‐Bridge6
Evap Emission Solenoid
A8
H‐Bridge7 / SlaveOut7
H‐Bridge7
Spray Bars
A9
H‐Bridge8 / SlaveOut8
H‐Bridge8
—
A10
FUEL1
INJECTOR or PWM OUTPUT
Primary Injector 1
A11
FUEL2
INJECTOR or PWM OUTPUT
Primary Injector 2
A12
FUEL3
INJECTOR or PWM OUTPUT
Primary Injector 3
A13
FUEL4
INJECTOR or PWM OUTPUT
Primary Injector 4
A14
FUEL5
INJECTOR or PWM OUTPUT
Wastegate Solenoid
A15
FUEL6
INJECTOR or PWM OUTPUT
Wastegate Solenoid 2
A16
FUEL7
INJECTOR or PWM OUTPUT
AirCon Comp Relay
A17
FUEL8
INJECTOR or PWM OUTPUT
Throttle Relay
A18
PWM1 /*FUEL9
PWM OUTPUT
Fuel Pump Relay
A19
PWM2 / *FUEL10
PWM OUTPUT
Alternator Control
A20
PWM3 / *FUEL11
PWM OUTPUT
Fuel Pump Relay 2
A21
PWM4 / *FUEL12
PWM OUTPUT
—
A22
PWM5
PWM OUTPUT
—
A23
PWM6
PWM OUTPUT
—
A24
PWM7
PWM OUTPUT
VVT Intake
A25
PWM8
PWM OUTPUT
VVT Exhaust
A26
IGN1
CYL 1 IGNITION OUTPUT
Ignition 1
A27
IGN2
CYL 2 IGNITION OUTPUT
Ignition 2
A28
IGN3
CYL 3 IGNITION OUTPUT
Ignition 3
A29
IGN4
CYL 4 IGNITION OUTPUT
Ignition 4
A30
IGN5
CYL 5 IGNITION OUTPUT
—
A31
IGN6
CYL 6 IGNITION OUTPUT
—
A32
PWRGND
POWER GROUND
Throttle Ground and Cruise Ground
A33
PWRGND
POWER GROUND
Throttle Ground
A34
PWRGND
POWER GROUND
ECM Ground
Connector B
ECU pin
Syvecs description
Function
Application notes
B1
PWRGND
POWER GROUND
Ground
B2
CAN2L
—
—
B3
CAN2H
—
—
B4
KNOCK
KNOCK
—
B5
KNOCK2
KNOCK2
—
B6
PVBAT
—
—
B7
IVBAT
—
—
B8
LAM1A
Lamv / LamD1+/ LamLun1
Grey NTK
B9
LAM1B
Lami / LamD1‐ /LamIP1
White NTK
B10
LAM1C
LamLIA1
—
B11
LAM1D
LamGND / LamLVM1
Black NTK
B12
LAM1HEATER
LAMBDA HEATER
Blue NTK
B13
IVBAT
—
Yellow NTK
B14
LAM2A
Lamv / LamD1+/ LamLun1
—
B15
LAM2B
Lami / LamD1‐ /LamIP1
—
B16
LAM2C
LamLIA1
—
B17
LAM2D
LamGND / LamLVM1
—
B18
LAM2HEATER
LAMBDA HEATER
—
B19
IVBAT
—
Power Supply
B20
KLINE
Kline
—
B21
RS232RX
RS232RX
—
B22
RS232TX
RS232TX
—
B23
LANRX‐
Cat5 Pin2
—
B24
LANRX+
Cat5 Pin1
—
B25
LANTX‐
Cat5 Pin6
—
B26
LANTX+
Cat5 Pin3
—
Connector C
ECU pin
Syvecs description
Function
Application notes
C1
KNOCK GROUND
KNOCK GROUND
—
C2
ANGND
SENSOR GND
TPS,
C3
ANGND
SENSOR GND
—
C4
ANGND
SENSOR GND
—
C5
5V OUT
5V OUT
Exhaust Cam Sensor, TPS
C6
5V OUT
5V OUT
—
C7
5V OUT
5V OUT
—
C8
CAN L
Can Low
—
C9
CAN H
Can High
—
C10
AN01
BI-POLAR INPUTS
Crank Sensor
C11
AN02
BI-POLAR INPUTS
Exhaust Cam Sensor
C12
AN03
BI-POLAR INPUTS
Intake Cam Sensor
C13
AN04
BI-POLAR INPUTS
—
C14
AN05
UNI-POLAR INPUTS
—
C15
AN06
UNI-POLAR INPUTS
—
C16
AN07
UNI-POLAR INPUTS
TPS1A
C17
AN08
UNI-POLAR INPUTS
TPS1B
C18
AN09
VOLT-INPUTS
MAP Absolute Sensor
C19
AN10
VOLT-INPUTS
PPS1
C20
AN11
VOLT-INPUTS
PPS2
C21
AN12
VOLT-INPUTS
MAF
C22
AN13
RESISTIVE INPUTS
Air Charge Temp 2
C23
AN14
RESISTIVE INPUTS
Air Charge Temp
C24
AN15
RESISTIVE INPUTS
ECT1
C25
AN16
RESISTIVE INPUTS
Cruise Switch
C26
EGT1-
EGT1 -
—
C27
EGT1+
EGT1 +
—
C28
PWR CTR IN
MAIN RELAY INPUT SW
Ignition Switch
C29
AN S1 / Slave An01
UNI-POLAR INPUTS
Alternator Feed
C30
AN S2 / Slave An02
UNI-POLAR INPUTS
Oil Pressure Sw
C31
AN S3 / Slave An03
UNI-POLAR INPUTS
Clutch Sw
C32
AN S4 / Slave An04
UNI-POLAR INPUTS
Fuel temp
C33
AN S5 / Slave An05
UNI-POLAR INPUTS
Spray Bar Request
C34
AN S6 / Slave An06
UNI-POLAR INPUTS
Brake Switch
Revision 2: Syvecs Mitsubishi Evo X Manual SST S7Plus Plug-in ECUSyvecs S7Plus general-purpose ECU shown as a family reference; vehicle-specific kit and adaptor may differ. Manufacturer photograph, reproduced with permission. Image source.
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Mitsubishi Evo X Manual SST S7Plus, with product code S7Plus-EVOX. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs Mitsubishi Evo X Manual SST S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
From the Syvecs Mitsubishi Evo X installation guide, revision 1.2. The tables list ECU-side pins and the manufacturer's vehicle-specific notes, not the complete original vehicle connectors. A dash denotes a blank field in the source, not proof of an unused circuit. Confirm the ECU, harness revision and connector orientation against the manufacturer document.