
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Mitsubishi Evo X Manual SST S7Plus, with product code S7Plus-EVOX. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs Mitsubishi Evo X Manual SST S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
Sources
- Syvecs Mitsubishi Evo X Manual SST S7Plus product listing and application
- Manufacturer kit installation and pinout manual
- Syvecs plug-in kit support index
Manufacturer ECU connector schedules
From the Syvecs Mitsubishi Evo X installation guide, revision 1.2. The tables list ECU-side pins and the manufacturer's vehicle-specific notes, not the complete original vehicle connectors. A dash denotes a blank field in the source, not proof of an unused circuit. Confirm the ECU, harness revision and connector orientation against the manufacturer document.
Connector A
| ECU pin | Syvecs description | Function | Application notes |
|---|---|---|---|
| A1 | PWR CTR OUT | MAIN RELAY OUTPUT | Main Relay |
| A2 | H‐Bridge1 / SlaveOut1 | H‐Bridge1 | DBW+ |
| A3 | H‐Bridge2 / SlaveOut2 | H‐Bridge2 | DBW‐ |
| A4 | H‐Bridge3 / SlaveOut3 | H‐Bridge3 | — |
| A5 | H‐Bridge4 / SlaveOut4 | H‐Bridge4 | — |
| A6 | H‐Bridge5 / SlaveOut5 | H‐Bridge5 | Evap Solenoid |
| A7 | H‐Bridge6 / SlaveOut6 | H‐Bridge6 | Evap Emission Solenoid |
| A8 | H‐Bridge7 / SlaveOut7 | H‐Bridge7 | Spray Bars |
| A9 | H‐Bridge8 / SlaveOut8 | H‐Bridge8 | — |
| A10 | FUEL1 | INJECTOR or PWM OUTPUT | Primary Injector 1 |
| A11 | FUEL2 | INJECTOR or PWM OUTPUT | Primary Injector 2 |
| A12 | FUEL3 | INJECTOR or PWM OUTPUT | Primary Injector 3 |
| A13 | FUEL4 | INJECTOR or PWM OUTPUT | Primary Injector 4 |
| A14 | FUEL5 | INJECTOR or PWM OUTPUT | Wastegate Solenoid |
| A15 | FUEL6 | INJECTOR or PWM OUTPUT | Wastegate Solenoid 2 |
| A16 | FUEL7 | INJECTOR or PWM OUTPUT | AirCon Comp Relay |
| A17 | FUEL8 | INJECTOR or PWM OUTPUT | Throttle Relay |
| A18 | PWM1 /*FUEL9 | PWM OUTPUT | Fuel Pump Relay |
| A19 | PWM2 / *FUEL10 | PWM OUTPUT | Alternator Control |
| A20 | PWM3 / *FUEL11 | PWM OUTPUT | Fuel Pump Relay 2 |
| A21 | PWM4 / *FUEL12 | PWM OUTPUT | — |
| A22 | PWM5 | PWM OUTPUT | — |
| A23 | PWM6 | PWM OUTPUT | — |
| A24 | PWM7 | PWM OUTPUT | VVT Intake |
| A25 | PWM8 | PWM OUTPUT | VVT Exhaust |
| A26 | IGN1 | CYL 1 IGNITION OUTPUT | Ignition 1 |
| A27 | IGN2 | CYL 2 IGNITION OUTPUT | Ignition 2 |
| A28 | IGN3 | CYL 3 IGNITION OUTPUT | Ignition 3 |
| A29 | IGN4 | CYL 4 IGNITION OUTPUT | Ignition 4 |
| A30 | IGN5 | CYL 5 IGNITION OUTPUT | — |
| A31 | IGN6 | CYL 6 IGNITION OUTPUT | — |
| A32 | PWRGND | POWER GROUND | Throttle Ground and Cruise Ground |
| A33 | PWRGND | POWER GROUND | Throttle Ground |
| A34 | PWRGND | POWER GROUND | ECM Ground |
Connector B
| ECU pin | Syvecs description | Function | Application notes |
|---|---|---|---|
| B1 | PWRGND | POWER GROUND | Ground |
| B2 | CAN2L | — | — |
| B3 | CAN2H | — | — |
| B4 | KNOCK | KNOCK | — |
| B5 | KNOCK2 | KNOCK2 | — |
| B6 | PVBAT | — | — |
| B7 | IVBAT | — | — |
| B8 | LAM1A | Lamv / LamD1+/ LamLun1 | Grey NTK |
| B9 | LAM1B | Lami / LamD1‐ /LamIP1 | White NTK |
| B10 | LAM1C | LamLIA1 | — |
| B11 | LAM1D | LamGND / LamLVM1 | Black NTK |
| B12 | LAM1HEATER | LAMBDA HEATER | Blue NTK |
| B13 | IVBAT | — | Yellow NTK |
| B14 | LAM2A | Lamv / LamD1+/ LamLun1 | — |
| B15 | LAM2B | Lami / LamD1‐ /LamIP1 | — |
| B16 | LAM2C | LamLIA1 | — |
| B17 | LAM2D | LamGND / LamLVM1 | — |
| B18 | LAM2HEATER | LAMBDA HEATER | — |
| B19 | IVBAT | — | Power Supply |
| B20 | KLINE | Kline | — |
| B21 | RS232RX | RS232RX | — |
| B22 | RS232TX | RS232TX | — |
| B23 | LANRX‐ | Cat5 Pin2 | — |
| B24 | LANRX+ | Cat5 Pin1 | — |
| B25 | LANTX‐ | Cat5 Pin6 | — |
| B26 | LANTX+ | Cat5 Pin3 | — |
Connector C
| ECU pin | Syvecs description | Function | Application notes |
|---|---|---|---|
| C1 | KNOCK GROUND | KNOCK GROUND | — |
| C2 | ANGND | SENSOR GND | TPS, |
| C3 | ANGND | SENSOR GND | — |
| C4 | ANGND | SENSOR GND | — |
| C5 | 5V OUT | 5V OUT | Exhaust Cam Sensor, TPS |
| C6 | 5V OUT | 5V OUT | — |
| C7 | 5V OUT | 5V OUT | — |
| C8 | CAN L | Can Low | — |
| C9 | CAN H | Can High | — |
| C10 | AN01 | BI-POLAR INPUTS | Crank Sensor |
| C11 | AN02 | BI-POLAR INPUTS | Exhaust Cam Sensor |
| C12 | AN03 | BI-POLAR INPUTS | Intake Cam Sensor |
| C13 | AN04 | BI-POLAR INPUTS | — |
| C14 | AN05 | UNI-POLAR INPUTS | — |
| C15 | AN06 | UNI-POLAR INPUTS | — |
| C16 | AN07 | UNI-POLAR INPUTS | TPS1A |
| C17 | AN08 | UNI-POLAR INPUTS | TPS1B |
| C18 | AN09 | VOLT-INPUTS | MAP Absolute Sensor |
| C19 | AN10 | VOLT-INPUTS | PPS1 |
| C20 | AN11 | VOLT-INPUTS | PPS2 |
| C21 | AN12 | VOLT-INPUTS | MAF |
| C22 | AN13 | RESISTIVE INPUTS | Air Charge Temp 2 |
| C23 | AN14 | RESISTIVE INPUTS | Air Charge Temp |
| C24 | AN15 | RESISTIVE INPUTS | ECT1 |
| C25 | AN16 | RESISTIVE INPUTS | Cruise Switch |
| C26 | EGT1- | EGT1 - | — |
| C27 | EGT1+ | EGT1 + | — |
| C28 | PWR CTR IN | MAIN RELAY INPUT SW | Ignition Switch |
| C29 | AN S1 / Slave An01 | UNI-POLAR INPUTS | Alternator Feed |
| C30 | AN S2 / Slave An02 | UNI-POLAR INPUTS | Oil Pressure Sw |
| C31 | AN S3 / Slave An03 | UNI-POLAR INPUTS | Clutch Sw |
| C32 | AN S4 / Slave An04 | UNI-POLAR INPUTS | Fuel temp |
| C33 | AN S5 / Slave An05 | UNI-POLAR INPUTS | Spray Bar Request |
| C34 | AN S6 / Slave An06 | UNI-POLAR INPUTS | Brake Switch |