Removed text is struck through; added text is highlighted.
Syvecs S7Plus general-purpose ECU shown as a family reference; vehicle-specific kit and adaptor may differ. Manufacturer photograph, reproduced with permission. Image source.
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Yamaha YXZ1000R S7Plus, with product code S7Plus-YAMXYZ. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs Yamaha YXZ1000R S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
Sources
Syvecs Yamaha YXZ1000R S7Plus product listing and applicationManufacturer kit installation and pinout manualSyvecs plug-in kit support index
Manufacturer ECU connector schedules
From the Syvecs Yamaha YXZ installation guide, revision 1.2. The tables list ECU-side pins and the manufacturer's vehicle-specific notes, not the complete original vehicle connectors. A dash denotes a blank field in the source, not proof of an unused circuit. Confirm the ECU, harness revision and connector orientation against the manufacturer document.
Connector A
ECU pinSyvecs descriptionFunctionApplication notesA1PWR CTR OUTMAIN RELAY OUTPUT—A2H‐Bridge1 / SlaveOut1H-Bridge1—A3H‐Bridge2 / SlaveOut2H-Bridge2—A4H‐Bridge3 / SlaveOut3H-Bridge3Air Induction Relay/evapA5H‐Bridge4 / SlaveOut4H-Bridge4—A6H‐Bridge5 / SlaveOut5H-Bridge5—A7H‐Bridge6 / SlaveOut6H-Bridge6—A8H‐Bridge7 / SlaveOut7H-Bridge7—A9H‐Bridge8 / SlaveOut8H-Bridge8—A10FUEL1INJECTOR or PWM OUTPUTPrimary Injector 1A11FUEL2INJECTOR or PWM OUTPUTPrimary Injector 2A12FUEL3INJECTOR or PWM OUTPUTPrimary Injector 3A13FUEL4INJECTOR or PWM OUTPUTStart OutputA14FUEL5INJECTOR or PWM OUTPUTStepper motor 1A15FUEL6INJECTOR or PWM OUTPUTStepper motor 2A16FUEL7INJECTOR or PWM OUTPUTStepper motor 3A17FUEL8INJECTOR or PWM OUTPUTStepper motor 4A18PWM1 /*FUEL9PWM OUTPUTTachoA19PWM2 / *FUEL10PWM OUTPUT—A20PWM3 / *FUEL11PWM OUTPUTRad Fan Relay - CanAmA21PWM4 / *FUEL12PWM OUTPUTSeat Belt LightA22PWM5PWM OUTPUTParking Brake BuzzerA23PWM6PWM OUTPUTDiff Relay DownA24PWM7PWM OUTPUTDiff Relay UpA25PWM8PWM OUTPUTMain RelayA26IGN1CYL 1 IGNITION OUTPUTIgnition 1A27IGN2CYL 2 IGNITION OUTPUTIgnition 2A28IGN3CYL 3 IGNITION OUTPUTIgnition 3A29IGN4CYL 4 IGNITION OUTPUT—A30IGN5CYL 5 IGNITION OUTPUT—A31IGN6CYL 6 IGNITION OUTPUT—A32PWRGNDPOWER GROUNDGroundA33PWRGNDPOWER GROUNDGroundA34PWRGNDPOWER GROUNDGround
Open each version to inspect formatting, tables and photographs.
Revision 2: Syvecs Yamaha YXZ1000R S7Plus Plug-in ECUSyvecs S7Plus general-purpose ECU shown as a family reference; vehicle-specific kit and adaptor may differ. Manufacturer photograph, reproduced with permission. Image source.
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Yamaha YXZ1000R S7Plus, with product code S7Plus-YAMXYZ. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs Yamaha YXZ1000R S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
From the Syvecs Yamaha YXZ installation guide, revision 1.2. The tables list ECU-side pins and the manufacturer's vehicle-specific notes, not the complete original vehicle connectors. A dash denotes a blank field in the source, not proof of an unused circuit. Confirm the ECU, harness revision and connector orientation against the manufacturer document.
Connector A
ECU pin
Syvecs description
Function
Application notes
A1
PWR CTR OUT
MAIN RELAY OUTPUT
—
A2
H‐Bridge1 / SlaveOut1
H-Bridge1
—
A3
H‐Bridge2 / SlaveOut2
H-Bridge2
—
A4
H‐Bridge3 / SlaveOut3
H-Bridge3
Air Induction Relay/evap
A5
H‐Bridge4 / SlaveOut4
H-Bridge4
—
A6
H‐Bridge5 / SlaveOut5
H-Bridge5
—
A7
H‐Bridge6 / SlaveOut6
H-Bridge6
—
A8
H‐Bridge7 / SlaveOut7
H-Bridge7
—
A9
H‐Bridge8 / SlaveOut8
H-Bridge8
—
A10
FUEL1
INJECTOR or PWM OUTPUT
Primary Injector 1
A11
FUEL2
INJECTOR or PWM OUTPUT
Primary Injector 2
A12
FUEL3
INJECTOR or PWM OUTPUT
Primary Injector 3
A13
FUEL4
INJECTOR or PWM OUTPUT
Start Output
A14
FUEL5
INJECTOR or PWM OUTPUT
Stepper motor 1
A15
FUEL6
INJECTOR or PWM OUTPUT
Stepper motor 2
A16
FUEL7
INJECTOR or PWM OUTPUT
Stepper motor 3
A17
FUEL8
INJECTOR or PWM OUTPUT
Stepper motor 4
A18
PWM1 /*FUEL9
PWM OUTPUT
Tacho
A19
PWM2 / *FUEL10
PWM OUTPUT
—
A20
PWM3 / *FUEL11
PWM OUTPUT
Rad Fan Relay - CanAm
A21
PWM4 / *FUEL12
PWM OUTPUT
Seat Belt Light
A22
PWM5
PWM OUTPUT
Parking Brake Buzzer
A23
PWM6
PWM OUTPUT
Diff Relay Down
A24
PWM7
PWM OUTPUT
Diff Relay Up
A25
PWM8
PWM OUTPUT
Main Relay
A26
IGN1
CYL 1 IGNITION OUTPUT
Ignition 1
A27
IGN2
CYL 2 IGNITION OUTPUT
Ignition 2
A28
IGN3
CYL 3 IGNITION OUTPUT
Ignition 3
A29
IGN4
CYL 4 IGNITION OUTPUT
—
A30
IGN5
CYL 5 IGNITION OUTPUT
—
A31
IGN6
CYL 6 IGNITION OUTPUT
—
A32
PWRGND
POWER GROUND
Ground
A33
PWRGND
POWER GROUND
Ground
A34
PWRGND
POWER GROUND
Ground
Connector B
ECU pin
Syvecs description
Function
Application notes
B1
PWRGND
POWER GROUND
Ground
B2
CAN2L
—
—
B3
CAN2H
—
—
B4
KNOCK
KNOCK
—
B5
KNOCK 2
KNOCK 2
—
B6
PVBAT
—
—
B7
IVBAT
—
12v Switch
B8
LAM1A
Lamv / LamD1+/ LamLun1
Grey NTK
B9
LAM1B
Lami / LamD1‐ /LamIP1
White NTK
B10
LAM1C
LamLIA1
—
B11
LAM1D
LamGND / LamLVM1
Black NTK
B12
LAM1HEATER
LAMBDA HEATER
Blue NTK
B13
IVBAT
—
Yellow NTK
B14
LAM2A
Lamv / LamD1+/ LamLun1
2.2v
B15
LAM2B
Lami / LamD1‐ /LamIP1
1.8v
B16
LAM2C
LamLIA1
—
B17
LAM2D
LamGND / LamLVM1
—
B18
LAM2HEATER
LAMBDA HEATER
—
B19
IVBAT
—
—
B20
KLINE
Kline
—
B21
RS232RX
RS232RX
—
B22
RS232TX
RS232TX
—
B23
LANRX‐
Cat5 Pin2
—
B24
LANRX+
Cat5 Pin1
—
B25
LANTX‐
Cat5 Pin6
—
B26
LANTX+
Cat5 Pin3
—
Connector C
ECU pin
Syvecs description
Function
Application notes
C1
KNOCKGND
KNOCKGND
—
C2
ANGND
SENSOR GND
—
C3
ANGND
SENSOR GND
—
C4
ANGND
SENSOR GND
—
C5
5V OUT
5V OUT
TPS, Map
C6
5V OUT
5V OUT
—
C7
5V OUT
5V OUT
Gear Pot 5v - CanAm
C8
CAN L
Can Low
Can Low
C9
CAN H
Can High
Can High
C10
AN01
BI-POLAR INPUTS
Crank
C11
AN02
BI-POLAR INPUTS
Diff Switch
C12
AN03
BI-POLAR INPUTS
Diff Servo
C13
AN04
BI-POLAR INPUTS
Intake pressure - CAM PHASE
C14
AN05
UNI-POLAR INPUTS
Neutral
C15
AN06
UNI-POLAR INPUTS
Gear Position
C16
AN07
UNI-POLAR INPUTS
Diff Lock Rotary 2
C17
AN08
UNI-POLAR INPUTS
Speed
C18
AN09
VOLT-INPUTS
—
C19
AN10
VOLT-INPUTS
TPS
C20
AN11
VOLT-INPUTS
Intake pressure 1
C21
AN12
VOLT-INPUTS
—
C22
AN13
RESISTIVE INPUTS
Coolant Temp
C23
AN14
RESISTIVE INPUTS
Intake Temp
C24
AN15
RESISTIVE INPUTS
Seat Belt
C25
AN16
RESISTIVE INPUTS
Lean Angle
C26
EGT1-
EGT1 -
—
C27
EGT1+
EGT1 +
—
C28
PWR CTR IN
MAIN RELAY INPUT SW
—
C29
AN S1 / Slave An01
UNI-POLAR INPUTS
Diff Servo 2 Position
C30
AN S2 / Slave An02
UNI-POLAR INPUTS
Brake Sw
C31
AN S3 / Slave An03
UNI-POLAR INPUTS
Clutch Sw
C32
AN S4 / Slave An04
UNI-POLAR INPUTS
Diff Position 3 - 4WD Active
C33
AN S5 / Slave An05
UNI-POLAR INPUTS
Diff Switch - 2wd = 12v
C34
AN S6 / Slave An06
UNI-POLAR INPUTS
Diff Lock Switch = Ground when active
Revision 2: Syvecs Yamaha YXZ1000R S7Plus Plug-in ECUSyvecs S7Plus general-purpose ECU shown as a family reference; vehicle-specific kit and adaptor may differ. Manufacturer photograph, reproduced with permission. Image source.
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Yamaha YXZ1000R S7Plus, with product code S7Plus-YAMXYZ. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs Yamaha YXZ1000R S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
From the Syvecs Yamaha YXZ installation guide, revision 1.2. The tables list ECU-side pins and the manufacturer's vehicle-specific notes, not the complete original vehicle connectors. A dash denotes a blank field in the source, not proof of an unused circuit. Confirm the ECU, harness revision and connector orientation against the manufacturer document.