
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Yamaha YXZ1000R S7Plus, with product code S7Plus-YAMXYZ. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs Yamaha YXZ1000R S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
Sources
- Syvecs Yamaha YXZ1000R S7Plus product listing and application
- Manufacturer kit installation and pinout manual
- Syvecs plug-in kit support index
Manufacturer ECU connector schedules
From the Syvecs Yamaha YXZ installation guide, revision 1.2. The tables list ECU-side pins and the manufacturer's vehicle-specific notes, not the complete original vehicle connectors. A dash denotes a blank field in the source, not proof of an unused circuit. Confirm the ECU, harness revision and connector orientation against the manufacturer document.
Connector A
| ECU pin | Syvecs description | Function | Application notes |
|---|---|---|---|
| A1 | PWR CTR OUT | MAIN RELAY OUTPUT | — |
| A2 | H‐Bridge1 / SlaveOut1 | H-Bridge1 | — |
| A3 | H‐Bridge2 / SlaveOut2 | H-Bridge2 | — |
| A4 | H‐Bridge3 / SlaveOut3 | H-Bridge3 | Air Induction Relay/evap |
| A5 | H‐Bridge4 / SlaveOut4 | H-Bridge4 | — |
| A6 | H‐Bridge5 / SlaveOut5 | H-Bridge5 | — |
| A7 | H‐Bridge6 / SlaveOut6 | H-Bridge6 | — |
| A8 | H‐Bridge7 / SlaveOut7 | H-Bridge7 | — |
| A9 | H‐Bridge8 / SlaveOut8 | H-Bridge8 | — |
| A10 | FUEL1 | INJECTOR or PWM OUTPUT | Primary Injector 1 |
| A11 | FUEL2 | INJECTOR or PWM OUTPUT | Primary Injector 2 |
| A12 | FUEL3 | INJECTOR or PWM OUTPUT | Primary Injector 3 |
| A13 | FUEL4 | INJECTOR or PWM OUTPUT | Start Output |
| A14 | FUEL5 | INJECTOR or PWM OUTPUT | Stepper motor 1 |
| A15 | FUEL6 | INJECTOR or PWM OUTPUT | Stepper motor 2 |
| A16 | FUEL7 | INJECTOR or PWM OUTPUT | Stepper motor 3 |
| A17 | FUEL8 | INJECTOR or PWM OUTPUT | Stepper motor 4 |
| A18 | PWM1 /*FUEL9 | PWM OUTPUT | Tacho |
| A19 | PWM2 / *FUEL10 | PWM OUTPUT | — |
| A20 | PWM3 / *FUEL11 | PWM OUTPUT | Rad Fan Relay - CanAm |
| A21 | PWM4 / *FUEL12 | PWM OUTPUT | Seat Belt Light |
| A22 | PWM5 | PWM OUTPUT | Parking Brake Buzzer |
| A23 | PWM6 | PWM OUTPUT | Diff Relay Down |
| A24 | PWM7 | PWM OUTPUT | Diff Relay Up |
| A25 | PWM8 | PWM OUTPUT | Main Relay |
| A26 | IGN1 | CYL 1 IGNITION OUTPUT | Ignition 1 |
| A27 | IGN2 | CYL 2 IGNITION OUTPUT | Ignition 2 |
| A28 | IGN3 | CYL 3 IGNITION OUTPUT | Ignition 3 |
| A29 | IGN4 | CYL 4 IGNITION OUTPUT | — |
| A30 | IGN5 | CYL 5 IGNITION OUTPUT | — |
| A31 | IGN6 | CYL 6 IGNITION OUTPUT | — |
| A32 | PWRGND | POWER GROUND | Ground |
| A33 | PWRGND | POWER GROUND | Ground |
| A34 | PWRGND | POWER GROUND | Ground |
Connector B
| ECU pin | Syvecs description | Function | Application notes |
|---|---|---|---|
| B1 | PWRGND | POWER GROUND | Ground |
| B2 | CAN2L | — | — |
| B3 | CAN2H | — | — |
| B4 | KNOCK | KNOCK | — |
| B5 | KNOCK 2 | KNOCK 2 | — |
| B6 | PVBAT | — | — |
| B7 | IVBAT | — | 12v Switch |
| B8 | LAM1A | Lamv / LamD1+/ LamLun1 | Grey NTK |
| B9 | LAM1B | Lami / LamD1‐ /LamIP1 | White NTK |
| B10 | LAM1C | LamLIA1 | — |
| B11 | LAM1D | LamGND / LamLVM1 | Black NTK |
| B12 | LAM1HEATER | LAMBDA HEATER | Blue NTK |
| B13 | IVBAT | — | Yellow NTK |
| B14 | LAM2A | Lamv / LamD1+/ LamLun1 | 2.2v |
| B15 | LAM2B | Lami / LamD1‐ /LamIP1 | 1.8v |
| B16 | LAM2C | LamLIA1 | — |
| B17 | LAM2D | LamGND / LamLVM1 | — |
| B18 | LAM2HEATER | LAMBDA HEATER | — |
| B19 | IVBAT | — | — |
| B20 | KLINE | Kline | — |
| B21 | RS232RX | RS232RX | — |
| B22 | RS232TX | RS232TX | — |
| B23 | LANRX‐ | Cat5 Pin2 | — |
| B24 | LANRX+ | Cat5 Pin1 | — |
| B25 | LANTX‐ | Cat5 Pin6 | — |
| B26 | LANTX+ | Cat5 Pin3 | — |
Connector C
| ECU pin | Syvecs description | Function | Application notes |
|---|---|---|---|
| C1 | KNOCKGND | KNOCKGND | — |
| C2 | ANGND | SENSOR GND | — |
| C3 | ANGND | SENSOR GND | — |
| C4 | ANGND | SENSOR GND | — |
| C5 | 5V OUT | 5V OUT | TPS, Map |
| C6 | 5V OUT | 5V OUT | — |
| C7 | 5V OUT | 5V OUT | Gear Pot 5v - CanAm |
| C8 | CAN L | Can Low | Can Low |
| C9 | CAN H | Can High | Can High |
| C10 | AN01 | BI-POLAR INPUTS | Crank |
| C11 | AN02 | BI-POLAR INPUTS | Diff Switch |
| C12 | AN03 | BI-POLAR INPUTS | Diff Servo |
| C13 | AN04 | BI-POLAR INPUTS | Intake pressure - CAM PHASE |
| C14 | AN05 | UNI-POLAR INPUTS | Neutral |
| C15 | AN06 | UNI-POLAR INPUTS | Gear Position |
| C16 | AN07 | UNI-POLAR INPUTS | Diff Lock Rotary 2 |
| C17 | AN08 | UNI-POLAR INPUTS | Speed |
| C18 | AN09 | VOLT-INPUTS | — |
| C19 | AN10 | VOLT-INPUTS | TPS |
| C20 | AN11 | VOLT-INPUTS | Intake pressure 1 |
| C21 | AN12 | VOLT-INPUTS | — |
| C22 | AN13 | RESISTIVE INPUTS | Coolant Temp |
| C23 | AN14 | RESISTIVE INPUTS | Intake Temp |
| C24 | AN15 | RESISTIVE INPUTS | Seat Belt |
| C25 | AN16 | RESISTIVE INPUTS | Lean Angle |
| C26 | EGT1- | EGT1 - | — |
| C27 | EGT1+ | EGT1 + | — |
| C28 | PWR CTR IN | MAIN RELAY INPUT SW | — |
| C29 | AN S1 / Slave An01 | UNI-POLAR INPUTS | Diff Servo 2 Position |
| C30 | AN S2 / Slave An02 | UNI-POLAR INPUTS | Brake Sw |
| C31 | AN S3 / Slave An03 | UNI-POLAR INPUTS | Clutch Sw |
| C32 | AN S4 / Slave An04 | UNI-POLAR INPUTS | Diff Position 3 - 4WD Active |
| C33 | AN S5 / Slave An05 | UNI-POLAR INPUTS | Diff Switch - 2wd = 12v |
| C34 | AN S6 / Slave An06 | UNI-POLAR INPUTS | Diff Lock Switch = Ground when active |