Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
Syvecs Standalone ECUs
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Changes from revision 2 to revision 2

Removed text is struck through; added text is highlighted.

Syvecs S7Plus general-purpose ECU shown as a family reference; the vehicle kit may differ. Syvecs photograph, reproduced with permission. Image source.

Product and application

Syvecs lists the Honda Civic Type R FK8 S7Plus vehicle-specific standalone ECU kit with manufacturer code S7Plus-HCVCFK8. Syvecs identifies this S7Plus kit for the Honda Civic Type R FK8 and describes direct- and port-injection control and electronic wastegate control. Its product page links a manual whose cover names both FK2 and FK8, although its filename refers to FK2.

A vehicle kit may include a particular carrier board, adaptor loom or auxiliary modules in addition to the ECU. Confirm the exact package, part number, engine, market and installation requirements with the manufacturer before installation.

Wiring and pinout status

The manufacturer guide identifies FK2 and FK8 on its cover and provides a common Civic FK ECU-side schedule below. Confirm the exact application and harness revision with Syvecs before connecting the ECU. The manufacturer's plug-in manual index is a starting point, but a document for a similarly named vehicle is not proof that its pins match this kit.

Calibration and support

Syvecs provides SCal software and family firmware, but an application-specific base calibration and correct hardware configuration are needed for the actual engine. Any features depend on ECU hardware, sensors, firmware and calibration. Review the manufacturer software portal and firmware archive.

Sources

Syvecs Honda Civic Type R FK8 S7Plus product listing and applicationSyvecs vehicle-specific manual index

Manufacturer ECU connector schedules

From the Syvecs Honda Type R FK2/FK8 installation guide, revision 1.2. The tables list ECU-side pins and the manufacturer's vehicle-specific notes, not the complete original vehicle connectors. A dash denotes a blank field in the source, not proof of an unused circuit. The document is labelled for FK2/FK8, while the table itself says Civic FK without a separate model-specific breakdown; confirm the kit and loom revision. Confirm the ECU, harness revision and connector orientation against the manufacturer document.

Connector A

ECU pinSyvecs descriptionApplication notesA1PWR CTR OUTMain RelayA2H‐Bridge1 / SlaveOut1DBWA3H‐Bridge2 / SlaveOut2DBWA4H‐Bridge3 / SlaveOut3Wastegate ControlA5H‐Bridge4 / SlaveOut4Wastegate ControlA6H‐Bridge5 / SlaveOut5—A7H‐Bridge6 / SlaveOut6VVT INA8H‐Bridge7 / SlaveOut7VVT ExA9H‐Bridge8 / SlaveOut8VTECA10FUEL1Primary Injector 1A11FUEL2Primary Injector 2A12FUEL3Primary Injector 3A13FUEL4Primary Injector 4 Primary Injector 4A14FUEL5Evap SolenoidA15FUEL6Reverse Gear SwitchA16FUEL7—A17FUEL8FUEL PUMPA18PWM1 /*FUEL9—A19PWM2 / *FUEL10Fan HighA20PWM3 / *FUEL11Turbo by-passA21PWM4 / *FUEL12A/C Clutch relayA22PWM5Starter cut relay 2A23PWM6Starter cut relay 1A24PWM7—A25PWM8Fan LowA26IGN1CYL 1 IGNITION OUTPUTA27IGN2CYL 2 IGNITION OUTPUTA28IGN3CYL 3 IGNITION OUTPUTA29IGN4CYL 4 IGNITION OUTPUTA30IGN5High Pressure Fuel PumpA31IGN6—A32PWRGNDPwrGndA33PWRGNDPwrGNdA34PWRGNDPwrGnd

Connector B

ECU pinSyvecs descriptionApplication notesB1PWRGND—B2CAN 2L—B3CAN 2H—B4KNOCK—B5KNOCK 2—B6PVBAT—B7IVBAT—B8LAM1A—B9LAM1B—B10LAM1C—B11LAM1D—B12LAM1HEATER—B13IVBAT—B14LAM2A—B15LAM2B—B16LAM2C—B17LAM2D—B18LAM2HEATER—B19IVBAT—B20KLINE—B21RS232RX—B22RS232TX—B23LANRX‐—B24LANRX+—B25LANTX‐—B26LANTX+—

Connector C

ECU pinSyvecs descriptionApplication notesC1KNOCK GROUND—C2ANGND—C3ANGND—C4ANGND—C55V OUT—C65V OUT—C75V OUT—C8CAN LCan LowC9CAN HCan HighC10AN01Crank (V3 Loom) / PPS2 (V4 LoomC11AN02Pre throttle boostC12AN03DIC13AN04Starter Signal SwitchC14AN05PPS1C15AN06PPS2(V3 Loom) / Crank (V4 LoomC16AN07inlet cam sensorC17AN08Ex CamC18AN09TPS 2 INPUTC19AN10TPS INPUTC20AN11Oil pressureC21AN12Wastegate positionC22AN13COOLANT TEMP INPUT1C23AN14ACTC24AN15Map SensorC25AN16Fuel PressureC26EGT1-—C27EGT1+—C28PWR CTR INIgnition SwitchC29AN S1 / Slave An01—C30AN S2 / Slave An02Intake cam sensorC31AN S3 / Slave An03Air Intake Temp from MafC32AN S4 / Slave An04Clutch Switch Gear BlipC33AN S5 / Slave An05Brake SwitchC34AN S6 / Slave An06Clutch Switch Gear Cut

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 2: Syvecs Honda Civic Type R FK8 S7Plus Plug-in ECU
Syvecs S7Plus ECU family
Syvecs S7Plus general-purpose ECU shown as a family reference; the vehicle kit may differ. Syvecs photograph, reproduced with permission. Image source.

Product and application

Syvecs lists the Honda Civic Type R FK8 S7Plus vehicle-specific standalone ECU kit with manufacturer code S7Plus-HCVCFK8. Syvecs identifies this S7Plus kit for the Honda Civic Type R FK8 and describes direct- and port-injection control and electronic wastegate control. Its product page links a manual whose cover names both FK2 and FK8, although its filename refers to FK2.

A vehicle kit may include a particular carrier board, adaptor loom or auxiliary modules in addition to the ECU. Confirm the exact package, part number, engine, market and installation requirements with the manufacturer before installation.

Wiring and pinout status

The manufacturer guide identifies FK2 and FK8 on its cover and provides a common Civic FK ECU-side schedule below. Confirm the exact application and harness revision with Syvecs before connecting the ECU. The manufacturer's plug-in manual index is a starting point, but a document for a similarly named vehicle is not proof that its pins match this kit.

Calibration and support

Syvecs provides SCal software and family firmware, but an application-specific base calibration and correct hardware configuration are needed for the actual engine. Any features depend on ECU hardware, sensors, firmware and calibration. Review the manufacturer software portal and firmware archive.

Sources

Manufacturer ECU connector schedules

From the Syvecs Honda Type R FK2/FK8 installation guide, revision 1.2. The tables list ECU-side pins and the manufacturer's vehicle-specific notes, not the complete original vehicle connectors. A dash denotes a blank field in the source, not proof of an unused circuit. The document is labelled for FK2/FK8, while the table itself says Civic FK without a separate model-specific breakdown; confirm the kit and loom revision. Confirm the ECU, harness revision and connector orientation against the manufacturer document.

Connector A

ECU pinSyvecs descriptionApplication notes
A1PWR CTR OUTMain Relay
A2H‐Bridge1 / SlaveOut1DBW
A3H‐Bridge2 / SlaveOut2DBW
A4H‐Bridge3 / SlaveOut3Wastegate Control
A5H‐Bridge4 / SlaveOut4Wastegate Control
A6H‐Bridge5 / SlaveOut5—
A7H‐Bridge6 / SlaveOut6VVT IN
A8H‐Bridge7 / SlaveOut7VVT Ex
A9H‐Bridge8 / SlaveOut8VTEC
A10FUEL1Primary Injector 1
A11FUEL2Primary Injector 2
A12FUEL3Primary Injector 3
A13FUEL4Primary Injector 4 Primary Injector 4
A14FUEL5Evap Solenoid
A15FUEL6Reverse Gear Switch
A16FUEL7—
A17FUEL8FUEL PUMP
A18PWM1 /*FUEL9—
A19PWM2 / *FUEL10Fan High
A20PWM3 / *FUEL11Turbo by-pass
A21PWM4 / *FUEL12A/C Clutch relay
A22PWM5Starter cut relay 2
A23PWM6Starter cut relay 1
A24PWM7—
A25PWM8Fan Low
A26IGN1CYL 1 IGNITION OUTPUT
A27IGN2CYL 2 IGNITION OUTPUT
A28IGN3CYL 3 IGNITION OUTPUT
A29IGN4CYL 4 IGNITION OUTPUT
A30IGN5High Pressure Fuel Pump
A31IGN6—
A32PWRGNDPwrGnd
A33PWRGNDPwrGNd
A34PWRGNDPwrGnd

Connector B

ECU pinSyvecs descriptionApplication notes
B1PWRGND—
B2CAN 2L—
B3CAN 2H—
B4KNOCK—
B5KNOCK 2—
B6PVBAT—
B7IVBAT—
B8LAM1A—
B9LAM1B—
B10LAM1C—
B11LAM1D—
B12LAM1HEATER—
B13IVBAT—
B14LAM2A—
B15LAM2B—
B16LAM2C—
B17LAM2D—
B18LAM2HEATER—
B19IVBAT—
B20KLINE—
B21RS232RX—
B22RS232TX—
B23LANRX‐—
B24LANRX+—
B25LANTX‐—
B26LANTX+—

Connector C

ECU pinSyvecs descriptionApplication notes
C1KNOCK GROUND—
C2ANGND—
C3ANGND—
C4ANGND—
C55V OUT—
C65V OUT—
C75V OUT—
C8CAN LCan Low
C9CAN HCan High
C10AN01Crank (V3 Loom) / PPS2 (V4 Loom
C11AN02Pre throttle boost
C12AN03DI
C13AN04Starter Signal Switch
C14AN05PPS1
C15AN06PPS2(V3 Loom) / Crank (V4 Loom
C16AN07inlet cam sensor
C17AN08Ex Cam
C18AN09TPS 2 INPUT
C19AN10TPS INPUT
C20AN11Oil pressure
C21AN12Wastegate position
C22AN13COOLANT TEMP INPUT1
C23AN14ACT
C24AN15Map Sensor
C25AN16Fuel Pressure
C26EGT1-—
C27EGT1+—
C28PWR CTR INIgnition Switch
C29AN S1 / Slave An01—
C30AN S2 / Slave An02Intake cam sensor
C31AN S3 / Slave An03Air Intake Temp from Maf
C32AN S4 / Slave An04Clutch Switch Gear Blip
C33AN S5 / Slave An05Brake Switch
C34AN S6 / Slave An06Clutch Switch Gear Cut
Revision 2: Syvecs Honda Civic Type R FK8 S7Plus Plug-in ECU
Syvecs S7Plus ECU family
Syvecs S7Plus general-purpose ECU shown as a family reference; the vehicle kit may differ. Syvecs photograph, reproduced with permission. Image source.

Product and application

Syvecs lists the Honda Civic Type R FK8 S7Plus vehicle-specific standalone ECU kit with manufacturer code S7Plus-HCVCFK8. Syvecs identifies this S7Plus kit for the Honda Civic Type R FK8 and describes direct- and port-injection control and electronic wastegate control. Its product page links a manual whose cover names both FK2 and FK8, although its filename refers to FK2.

A vehicle kit may include a particular carrier board, adaptor loom or auxiliary modules in addition to the ECU. Confirm the exact package, part number, engine, market and installation requirements with the manufacturer before installation.

Wiring and pinout status

The manufacturer guide identifies FK2 and FK8 on its cover and provides a common Civic FK ECU-side schedule below. Confirm the exact application and harness revision with Syvecs before connecting the ECU. The manufacturer's plug-in manual index is a starting point, but a document for a similarly named vehicle is not proof that its pins match this kit.

Calibration and support

Syvecs provides SCal software and family firmware, but an application-specific base calibration and correct hardware configuration are needed for the actual engine. Any features depend on ECU hardware, sensors, firmware and calibration. Review the manufacturer software portal and firmware archive.

Sources

Manufacturer ECU connector schedules

From the Syvecs Honda Type R FK2/FK8 installation guide, revision 1.2. The tables list ECU-side pins and the manufacturer's vehicle-specific notes, not the complete original vehicle connectors. A dash denotes a blank field in the source, not proof of an unused circuit. The document is labelled for FK2/FK8, while the table itself says Civic FK without a separate model-specific breakdown; confirm the kit and loom revision. Confirm the ECU, harness revision and connector orientation against the manufacturer document.

Connector A

ECU pinSyvecs descriptionApplication notes
A1PWR CTR OUTMain Relay
A2H‐Bridge1 / SlaveOut1DBW
A3H‐Bridge2 / SlaveOut2DBW
A4H‐Bridge3 / SlaveOut3Wastegate Control
A5H‐Bridge4 / SlaveOut4Wastegate Control
A6H‐Bridge5 / SlaveOut5—
A7H‐Bridge6 / SlaveOut6VVT IN
A8H‐Bridge7 / SlaveOut7VVT Ex
A9H‐Bridge8 / SlaveOut8VTEC
A10FUEL1Primary Injector 1
A11FUEL2Primary Injector 2
A12FUEL3Primary Injector 3
A13FUEL4Primary Injector 4 Primary Injector 4
A14FUEL5Evap Solenoid
A15FUEL6Reverse Gear Switch
A16FUEL7—
A17FUEL8FUEL PUMP
A18PWM1 /*FUEL9—
A19PWM2 / *FUEL10Fan High
A20PWM3 / *FUEL11Turbo by-pass
A21PWM4 / *FUEL12A/C Clutch relay
A22PWM5Starter cut relay 2
A23PWM6Starter cut relay 1
A24PWM7—
A25PWM8Fan Low
A26IGN1CYL 1 IGNITION OUTPUT
A27IGN2CYL 2 IGNITION OUTPUT
A28IGN3CYL 3 IGNITION OUTPUT
A29IGN4CYL 4 IGNITION OUTPUT
A30IGN5High Pressure Fuel Pump
A31IGN6—
A32PWRGNDPwrGnd
A33PWRGNDPwrGNd
A34PWRGNDPwrGnd

Connector B

ECU pinSyvecs descriptionApplication notes
B1PWRGND—
B2CAN 2L—
B3CAN 2H—
B4KNOCK—
B5KNOCK 2—
B6PVBAT—
B7IVBAT—
B8LAM1A—
B9LAM1B—
B10LAM1C—
B11LAM1D—
B12LAM1HEATER—
B13IVBAT—
B14LAM2A—
B15LAM2B—
B16LAM2C—
B17LAM2D—
B18LAM2HEATER—
B19IVBAT—
B20KLINE—
B21RS232RX—
B22RS232TX—
B23LANRX‐—
B24LANRX+—
B25LANTX‐—
B26LANTX+—

Connector C

ECU pinSyvecs descriptionApplication notes
C1KNOCK GROUND—
C2ANGND—
C3ANGND—
C4ANGND—
C55V OUT—
C65V OUT—
C75V OUT—
C8CAN LCan Low
C9CAN HCan High
C10AN01Crank (V3 Loom) / PPS2 (V4 Loom
C11AN02Pre throttle boost
C12AN03DI
C13AN04Starter Signal Switch
C14AN05PPS1
C15AN06PPS2(V3 Loom) / Crank (V4 Loom
C16AN07inlet cam sensor
C17AN08Ex Cam
C18AN09TPS 2 INPUT
C19AN10TPS INPUT
C20AN11Oil pressure
C21AN12Wastegate position
C22AN13COOLANT TEMP INPUT1
C23AN14ACT
C24AN15Map Sensor
C25AN16Fuel Pressure
C26EGT1-—
C27EGT1+—
C28PWR CTR INIgnition Switch
C29AN S1 / Slave An01—
C30AN S2 / Slave An02Intake cam sensor
C31AN S3 / Slave An03Air Intake Temp from Maf
C32AN S4 / Slave An04Clutch Switch Gear Blip
C33AN S5 / Slave An05Brake Switch
C34AN S6 / Slave An06Clutch Switch Gear Cut