
Product and application
Syvecs lists the Honda Civic Type R FK8 S7Plus vehicle-specific standalone ECU kit with manufacturer code S7Plus-HCVCFK8. Syvecs identifies this S7Plus kit for the Honda Civic Type R FK8 and describes direct- and port-injection control and electronic wastegate control. Its product page links a manual whose cover names both FK2 and FK8, although its filename refers to FK2.
A vehicle kit may include a particular carrier board, adaptor loom or auxiliary modules in addition to the ECU. Confirm the exact package, part number, engine, market and installation requirements with the manufacturer before installation.
Wiring and pinout status
The manufacturer guide identifies FK2 and FK8 on its cover and provides a common Civic FK ECU-side schedule below. Confirm the exact application and harness revision with Syvecs before connecting the ECU. The manufacturer's plug-in manual index is a starting point, but a document for a similarly named vehicle is not proof that its pins match this kit.
Calibration and support
Syvecs provides SCal software and family firmware, but an application-specific base calibration and correct hardware configuration are needed for the actual engine. Any features depend on ECU hardware, sensors, firmware and calibration. Review the manufacturer software portal and firmware archive.
Sources
- Syvecs Honda Civic Type R FK8 S7Plus product listing and application
- Syvecs vehicle-specific manual index
Manufacturer ECU connector schedules
From the Syvecs Honda Type R FK2/FK8 installation guide, revision 1.2. The tables list ECU-side pins and the manufacturer's vehicle-specific notes, not the complete original vehicle connectors. A dash denotes a blank field in the source, not proof of an unused circuit. The document is labelled for FK2/FK8, while the table itself says Civic FK without a separate model-specific breakdown; confirm the kit and loom revision. Confirm the ECU, harness revision and connector orientation against the manufacturer document.
Connector A
| ECU pin | Syvecs description | Application notes |
|---|---|---|
| A1 | PWR CTR OUT | Main Relay |
| A2 | H‐Bridge1 / SlaveOut1 | DBW |
| A3 | H‐Bridge2 / SlaveOut2 | DBW |
| A4 | H‐Bridge3 / SlaveOut3 | Wastegate Control |
| A5 | H‐Bridge4 / SlaveOut4 | Wastegate Control |
| A6 | H‐Bridge5 / SlaveOut5 | — |
| A7 | H‐Bridge6 / SlaveOut6 | VVT IN |
| A8 | H‐Bridge7 / SlaveOut7 | VVT Ex |
| A9 | H‐Bridge8 / SlaveOut8 | VTEC |
| A10 | FUEL1 | Primary Injector 1 |
| A11 | FUEL2 | Primary Injector 2 |
| A12 | FUEL3 | Primary Injector 3 |
| A13 | FUEL4 | Primary Injector 4 Primary Injector 4 |
| A14 | FUEL5 | Evap Solenoid |
| A15 | FUEL6 | Reverse Gear Switch |
| A16 | FUEL7 | — |
| A17 | FUEL8 | FUEL PUMP |
| A18 | PWM1 /*FUEL9 | — |
| A19 | PWM2 / *FUEL10 | Fan High |
| A20 | PWM3 / *FUEL11 | Turbo by-pass |
| A21 | PWM4 / *FUEL12 | A/C Clutch relay |
| A22 | PWM5 | Starter cut relay 2 |
| A23 | PWM6 | Starter cut relay 1 |
| A24 | PWM7 | — |
| A25 | PWM8 | Fan Low |
| A26 | IGN1 | CYL 1 IGNITION OUTPUT |
| A27 | IGN2 | CYL 2 IGNITION OUTPUT |
| A28 | IGN3 | CYL 3 IGNITION OUTPUT |
| A29 | IGN4 | CYL 4 IGNITION OUTPUT |
| A30 | IGN5 | High Pressure Fuel Pump |
| A31 | IGN6 | — |
| A32 | PWRGND | PwrGnd |
| A33 | PWRGND | PwrGNd |
| A34 | PWRGND | PwrGnd |
Connector B
| ECU pin | Syvecs description | Application notes |
|---|---|---|
| B1 | PWRGND | — |
| B2 | CAN 2L | — |
| B3 | CAN 2H | — |
| B4 | KNOCK | — |
| B5 | KNOCK 2 | — |
| B6 | PVBAT | — |
| B7 | IVBAT | — |
| B8 | LAM1A | — |
| B9 | LAM1B | — |
| B10 | LAM1C | — |
| B11 | LAM1D | — |
| B12 | LAM1HEATER | — |
| B13 | IVBAT | — |
| B14 | LAM2A | — |
| B15 | LAM2B | — |
| B16 | LAM2C | — |
| B17 | LAM2D | — |
| B18 | LAM2HEATER | — |
| B19 | IVBAT | — |
| B20 | KLINE | — |
| B21 | RS232RX | — |
| B22 | RS232TX | — |
| B23 | LANRX‐ | — |
| B24 | LANRX+ | — |
| B25 | LANTX‐ | — |
| B26 | LANTX+ | — |
Connector C
| ECU pin | Syvecs description | Application notes |
|---|---|---|
| C1 | KNOCK GROUND | — |
| C2 | ANGND | — |
| C3 | ANGND | — |
| C4 | ANGND | — |
| C5 | 5V OUT | — |
| C6 | 5V OUT | — |
| C7 | 5V OUT | — |
| C8 | CAN L | Can Low |
| C9 | CAN H | Can High |
| C10 | AN01 | Crank (V3 Loom) / PPS2 (V4 Loom |
| C11 | AN02 | Pre throttle boost |
| C12 | AN03 | DI |
| C13 | AN04 | Starter Signal Switch |
| C14 | AN05 | PPS1 |
| C15 | AN06 | PPS2(V3 Loom) / Crank (V4 Loom |
| C16 | AN07 | inlet cam sensor |
| C17 | AN08 | Ex Cam |
| C18 | AN09 | TPS 2 INPUT |
| C19 | AN10 | TPS INPUT |
| C20 | AN11 | Oil pressure |
| C21 | AN12 | Wastegate position |
| C22 | AN13 | COOLANT TEMP INPUT1 |
| C23 | AN14 | ACT |
| C24 | AN15 | Map Sensor |
| C25 | AN16 | Fuel Pressure |
| C26 | EGT1- | — |
| C27 | EGT1+ | — |
| C28 | PWR CTR IN | Ignition Switch |
| C29 | AN S1 / Slave An01 | — |
| C30 | AN S2 / Slave An02 | Intake cam sensor |
| C31 | AN S3 / Slave An03 | Air Intake Temp from Maf |
| C32 | AN S4 / Slave An04 | Clutch Switch Gear Blip |
| C33 | AN S5 / Slave An05 | Brake Switch |
| C34 | AN S6 / Slave An06 | Clutch Switch Gear Cut |