Removed text is struck through; added text is highlighted.
Syvecs S7Plus general-purpose ECU shown as a family reference; vehicle-specific kit and adaptor may differ. Manufacturer photograph, reproduced with permission. Image source.
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Honda Civic Type R FK2 S7Plus, with product code S7Plus-HCVCFK2. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs Honda Civic Type R FK2 S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
Sources
Syvecs Honda Civic Type R FK2 S7Plus product listing and applicationManufacturer kit installation and pinout manualSyvecs plug-in kit support index
Manufacturer ECU connector schedules
From the Syvecs Honda Type R FK2/FK8 installation guide, revision 1.2. The tables list ECU-side pins and the manufacturer's vehicle-specific notes, not the complete original vehicle connectors. A dash denotes a blank field in the source, not proof of an unused circuit. The document is labelled for FK2/FK8, while the table itself says Civic FK without a separate model-specific breakdown; confirm the kit and loom revision. Confirm the ECU, harness revision and connector orientation against the manufacturer document.
Open each version to inspect formatting, tables and photographs.
Revision 2: Syvecs Honda Civic Type R FK2 S7Plus Plug-in ECUSyvecs S7Plus general-purpose ECU shown as a family reference; vehicle-specific kit and adaptor may differ. Manufacturer photograph, reproduced with permission. Image source.
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Honda Civic Type R FK2 S7Plus, with product code S7Plus-HCVCFK2. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs Honda Civic Type R FK2 S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
From the Syvecs Honda Type R FK2/FK8 installation guide, revision 1.2. The tables list ECU-side pins and the manufacturer's vehicle-specific notes, not the complete original vehicle connectors. A dash denotes a blank field in the source, not proof of an unused circuit. The document is labelled for FK2/FK8, while the table itself says Civic FK without a separate model-specific breakdown; confirm the kit and loom revision. Confirm the ECU, harness revision and connector orientation against the manufacturer document.
Connector A
ECU pin
Syvecs description
Application notes
A1
PWR CTR OUT
Main Relay
A2
H‐Bridge1 / SlaveOut1
DBW
A3
H‐Bridge2 / SlaveOut2
DBW
A4
H‐Bridge3 / SlaveOut3
Wastegate Control
A5
H‐Bridge4 / SlaveOut4
Wastegate Control
A6
H‐Bridge5 / SlaveOut5
—
A7
H‐Bridge6 / SlaveOut6
VVT IN
A8
H‐Bridge7 / SlaveOut7
VVT Ex
A9
H‐Bridge8 / SlaveOut8
VTEC
A10
FUEL1
Primary Injector 1
A11
FUEL2
Primary Injector 2
A12
FUEL3
Primary Injector 3
A13
FUEL4
Primary Injector 4 Primary Injector 4
A14
FUEL5
Evap Solenoid
A15
FUEL6
Reverse Gear Switch
A16
FUEL7
—
A17
FUEL8
FUEL PUMP
A18
PWM1 /*FUEL9
—
A19
PWM2 / *FUEL10
Fan High
A20
PWM3 / *FUEL11
Turbo by-pass
A21
PWM4 / *FUEL12
A/C Clutch relay
A22
PWM5
Starter cut relay 2
A23
PWM6
Starter cut relay 1
A24
PWM7
—
A25
PWM8
Fan Low
A26
IGN1
CYL 1 IGNITION OUTPUT
A27
IGN2
CYL 2 IGNITION OUTPUT
A28
IGN3
CYL 3 IGNITION OUTPUT
A29
IGN4
CYL 4 IGNITION OUTPUT
A30
IGN5
High Pressure Fuel Pump
A31
IGN6
—
A32
PWRGND
PwrGnd
A33
PWRGND
PwrGNd
A34
PWRGND
PwrGnd
Connector B
ECU pin
Syvecs description
Application notes
B1
PWRGND
—
B2
CAN 2L
—
B3
CAN 2H
—
B4
KNOCK
—
B5
KNOCK 2
—
B6
PVBAT
—
B7
IVBAT
—
B8
LAM1A
—
B9
LAM1B
—
B10
LAM1C
—
B11
LAM1D
—
B12
LAM1HEATER
—
B13
IVBAT
—
B14
LAM2A
—
B15
LAM2B
—
B16
LAM2C
—
B17
LAM2D
—
B18
LAM2HEATER
—
B19
IVBAT
—
B20
KLINE
—
B21
RS232RX
—
B22
RS232TX
—
B23
LANRX‐
—
B24
LANRX+
—
B25
LANTX‐
—
B26
LANTX+
—
Connector C
ECU pin
Syvecs description
Application notes
C1
KNOCK GROUND
—
C2
ANGND
—
C3
ANGND
—
C4
ANGND
—
C5
5V OUT
—
C6
5V OUT
—
C7
5V OUT
—
C8
CAN L
Can Low
C9
CAN H
Can High
C10
AN01
Crank (V3 Loom) / PPS2 (V4 Loom
C11
AN02
Pre throttle boost
C12
AN03
DI
C13
AN04
Starter Signal Switch
C14
AN05
PPS1
C15
AN06
PPS2(V3 Loom) / Crank (V4 Loom
C16
AN07
inlet cam sensor
C17
AN08
Ex Cam
C18
AN09
TPS 2 INPUT
C19
AN10
TPS INPUT
C20
AN11
Oil pressure
C21
AN12
Wastegate position
C22
AN13
COOLANT TEMP INPUT1
C23
AN14
ACT
C24
AN15
Map Sensor
C25
AN16
Fuel Pressure
C26
EGT1-
—
C27
EGT1+
—
C28
PWR CTR IN
Ignition Switch
C29
AN S1 / Slave An01
—
C30
AN S2 / Slave An02
Intake cam sensor
C31
AN S3 / Slave An03
Air Intake Temp from Maf
C32
AN S4 / Slave An04
Clutch Switch Gear Blip
C33
AN S5 / Slave An05
Brake Switch
C34
AN S6 / Slave An06
Clutch Switch Gear Cut
Revision 2: Syvecs Honda Civic Type R FK2 S7Plus Plug-in ECUSyvecs S7Plus general-purpose ECU shown as a family reference; vehicle-specific kit and adaptor may differ. Manufacturer photograph, reproduced with permission. Image source.
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Honda Civic Type R FK2 S7Plus, with product code S7Plus-HCVCFK2. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs Honda Civic Type R FK2 S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
From the Syvecs Honda Type R FK2/FK8 installation guide, revision 1.2. The tables list ECU-side pins and the manufacturer's vehicle-specific notes, not the complete original vehicle connectors. A dash denotes a blank field in the source, not proof of an unused circuit. The document is labelled for FK2/FK8, while the table itself says Civic FK without a separate model-specific breakdown; confirm the kit and loom revision. Confirm the ECU, harness revision and connector orientation against the manufacturer document.