
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Honda Civic Type R FK2 S7Plus, with product code S7Plus-HCVCFK2. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs Honda Civic Type R FK2 S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
Sources
- Syvecs Honda Civic Type R FK2 S7Plus product listing and application
- Manufacturer kit installation and pinout manual
- Syvecs plug-in kit support index
Manufacturer ECU connector schedules
From the Syvecs Honda Type R FK2/FK8 installation guide, revision 1.2. The tables list ECU-side pins and the manufacturer's vehicle-specific notes, not the complete original vehicle connectors. A dash denotes a blank field in the source, not proof of an unused circuit. The document is labelled for FK2/FK8, while the table itself says Civic FK without a separate model-specific breakdown; confirm the kit and loom revision. Confirm the ECU, harness revision and connector orientation against the manufacturer document.
Connector A
| ECU pin | Syvecs description | Application notes |
|---|---|---|
| A1 | PWR CTR OUT | Main Relay |
| A2 | H‐Bridge1 / SlaveOut1 | DBW |
| A3 | H‐Bridge2 / SlaveOut2 | DBW |
| A4 | H‐Bridge3 / SlaveOut3 | Wastegate Control |
| A5 | H‐Bridge4 / SlaveOut4 | Wastegate Control |
| A6 | H‐Bridge5 / SlaveOut5 | — |
| A7 | H‐Bridge6 / SlaveOut6 | VVT IN |
| A8 | H‐Bridge7 / SlaveOut7 | VVT Ex |
| A9 | H‐Bridge8 / SlaveOut8 | VTEC |
| A10 | FUEL1 | Primary Injector 1 |
| A11 | FUEL2 | Primary Injector 2 |
| A12 | FUEL3 | Primary Injector 3 |
| A13 | FUEL4 | Primary Injector 4 Primary Injector 4 |
| A14 | FUEL5 | Evap Solenoid |
| A15 | FUEL6 | Reverse Gear Switch |
| A16 | FUEL7 | — |
| A17 | FUEL8 | FUEL PUMP |
| A18 | PWM1 /*FUEL9 | — |
| A19 | PWM2 / *FUEL10 | Fan High |
| A20 | PWM3 / *FUEL11 | Turbo by-pass |
| A21 | PWM4 / *FUEL12 | A/C Clutch relay |
| A22 | PWM5 | Starter cut relay 2 |
| A23 | PWM6 | Starter cut relay 1 |
| A24 | PWM7 | — |
| A25 | PWM8 | Fan Low |
| A26 | IGN1 | CYL 1 IGNITION OUTPUT |
| A27 | IGN2 | CYL 2 IGNITION OUTPUT |
| A28 | IGN3 | CYL 3 IGNITION OUTPUT |
| A29 | IGN4 | CYL 4 IGNITION OUTPUT |
| A30 | IGN5 | High Pressure Fuel Pump |
| A31 | IGN6 | — |
| A32 | PWRGND | PwrGnd |
| A33 | PWRGND | PwrGNd |
| A34 | PWRGND | PwrGnd |
Connector B
| ECU pin | Syvecs description | Application notes |
|---|---|---|
| B1 | PWRGND | — |
| B2 | CAN 2L | — |
| B3 | CAN 2H | — |
| B4 | KNOCK | — |
| B5 | KNOCK 2 | — |
| B6 | PVBAT | — |
| B7 | IVBAT | — |
| B8 | LAM1A | — |
| B9 | LAM1B | — |
| B10 | LAM1C | — |
| B11 | LAM1D | — |
| B12 | LAM1HEATER | — |
| B13 | IVBAT | — |
| B14 | LAM2A | — |
| B15 | LAM2B | — |
| B16 | LAM2C | — |
| B17 | LAM2D | — |
| B18 | LAM2HEATER | — |
| B19 | IVBAT | — |
| B20 | KLINE | — |
| B21 | RS232RX | — |
| B22 | RS232TX | — |
| B23 | LANRX‐ | — |
| B24 | LANRX+ | — |
| B25 | LANTX‐ | — |
| B26 | LANTX+ | — |
Connector C
| ECU pin | Syvecs description | Application notes |
|---|---|---|
| C1 | KNOCK GROUND | — |
| C2 | ANGND | — |
| C3 | ANGND | — |
| C4 | ANGND | — |
| C5 | 5V OUT | — |
| C6 | 5V OUT | — |
| C7 | 5V OUT | — |
| C8 | CAN L | Can Low |
| C9 | CAN H | Can High |
| C10 | AN01 | Crank (V3 Loom) / PPS2 (V4 Loom |
| C11 | AN02 | Pre throttle boost |
| C12 | AN03 | DI |
| C13 | AN04 | Starter Signal Switch |
| C14 | AN05 | PPS1 |
| C15 | AN06 | PPS2(V3 Loom) / Crank (V4 Loom |
| C16 | AN07 | inlet cam sensor |
| C17 | AN08 | Ex Cam |
| C18 | AN09 | TPS 2 INPUT |
| C19 | AN10 | TPS INPUT |
| C20 | AN11 | Oil pressure |
| C21 | AN12 | Wastegate position |
| C22 | AN13 | COOLANT TEMP INPUT1 |
| C23 | AN14 | ACT |
| C24 | AN15 | Map Sensor |
| C25 | AN16 | Fuel Pressure |
| C26 | EGT1- | — |
| C27 | EGT1+ | — |
| C28 | PWR CTR IN | Ignition Switch |
| C29 | AN S1 / Slave An01 | — |
| C30 | AN S2 / Slave An02 | Intake cam sensor |
| C31 | AN S3 / Slave An03 | Air Intake Temp from Maf |
| C32 | AN S4 / Slave An04 | Clutch Switch Gear Blip |
| C33 | AN S5 / Slave An05 | Brake Switch |
| C34 | AN S6 / Slave An06 | Clutch Switch Gear Cut |