Removed text is struck through; added text is highlighted.
Syvecs S7Plus general-purpose ECU shown as a family reference; vehicle-specific kit and adaptor may differ. Manufacturer photograph, reproduced with permission. Image source.
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Mercedes C63 SLS M156 S7Plus, with product code S7Plus-M156. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs Mercedes C63 SLS M156 S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
Sources
Syvecs Mercedes C63 SLS M156 S7Plus product listing and applicationManufacturer kit installation and pinout manualSyvecs plug-in kit support index
Manufacturer ECU connector schedules
From the Syvecs Mercedes M156/9 installation guide, revision 1.2. The tables list ECU-side pins and the manufacturer's vehicle-specific notes, not the complete original vehicle connectors. A dash denotes a blank field in the source, not proof of an unused circuit. Confirm the ECU, harness revision and connector orientation against the manufacturer document.
ECU pinSyvecs descriptionApplication notesB1PWRGNDPWR GNDB2CAN2L—B3CAN2H—B4KNOCKKNOCK SENSOR INPUTB5KNOCK 2Knock 2B6PVBATConstant 12vB7IVBAT12v from ECMB8LAM1APin6 on LSU4.9 ConnectorB9LAM1BPin1 on LSU4.9 ConnectorB10LAM1CPin5 on LSU4.9 ConnectorB11LAM1DPin2 on LSU4.9 ConnectorB12LAM1HEATERPin3 on LSU4.9 ConnectorB13IVBAT12v from ECMB14LAM2APin6 on LSU4.9 ConnectorB15LAM2BPin1 on LSU4.9 ConnectorB16LAM2CPin5 on LSU4.9 ConnectorB17LAM2DPin2 on LSU4.9 ConnectorB18LAM2HEATERPin3 on LSU4.9 ConnectorB19IVBATRed WireB20KLINEAlternator LinB21RS232RX / Can L—B22RS232TX / Can H—B23LANRX‐—B24LANRX+—B25LANTX‐—B26LANTX+—
Open each version to inspect formatting, tables and photographs.
Revision 2: Syvecs Mercedes C63 SLS M156 S7Plus Plug-in ECUSyvecs S7Plus general-purpose ECU shown as a family reference; vehicle-specific kit and adaptor may differ. Manufacturer photograph, reproduced with permission. Image source.
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Mercedes C63 SLS M156 S7Plus, with product code S7Plus-M156. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs Mercedes C63 SLS M156 S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
From the Syvecs Mercedes M156/9 installation guide, revision 1.2. The tables list ECU-side pins and the manufacturer's vehicle-specific notes, not the complete original vehicle connectors. A dash denotes a blank field in the source, not proof of an unused circuit. Confirm the ECU, harness revision and connector orientation against the manufacturer document.
Connector A
ECU pin
Syvecs description
Application notes
A1
PWR CTR OUT
Main Relay
A2
H‐Bridge1 / SlaveOut1
DBW+
A3
H‐Bridge2 / SlaveOut2
DBW-
A4
H‐Bridge3 / SlaveOut3
DBW+
A5
H‐Bridge4 / SlaveOut4
DBW-
A6
H‐Bridge5 / SlaveOut5
Starter
A7
H‐Bridge6 / SlaveOut6
Intake Manifold Switch Valve
A8
H‐Bridge7 / SlaveOut7
Oil Cooler Fan
A9
H‐Bridge8 / SlaveOut8
Water Injection
A10
FUEL1
CYL 1 INJECTOR
A11
FUEL2
CYL 2 INJECTOR
A12
FUEL3
CYL 3 INJECTOR
A13
FUEL4
CYL 4 INJECTOR
A14
FUEL5
CYL 5 INJECTOR
A15
FUEL6
CYL 6 INJECTOR
A16
FUEL7
CYL 7 INJECTOR
A17
FUEL8
CYL 8 INJECTOR
A18
PWM1 /*FUEL9
Heating System Shut off
A19
PWM2 / *FUEL10
Engine and AC Fan
A20
PWM3 / *FUEL11
Fuel Pump Relay
A21
PWM4 / *FUEL12
Coolant Thermostate heating element
A22
PWM5 / *FUEL13
Vvti 1EX -Flyback Solder Bridge Set
A23
PWM6 / *FUEL14
Vvti 2Ex -Flyback Solder Bridge Set
A24
PWM7 / *FUEL15
Vvti 1 -Flyback Solder Bridge Set
A25
PWM8 / *FUEL16
Vvti 2 -Flyback Solder Bridge Set
A26
IGN1
Ign 1 & 6
A27
IGN2
Ign 2 & 8
A28
IGN3
Ign 4 & 7
A29
IGN4
Ign 5 & 3
A30
IGN5
Fuel Pump Speed
A31
IGN6
—
A32
PWRGND
Black Wire
A33
PWRGND
ECU GND
A34
PWRGND
ECU GND
Connector B
ECU pin
Syvecs description
Application notes
B1
PWRGND
PWR GND
B2
CAN2L
—
B3
CAN2H
—
B4
KNOCK
KNOCK SENSOR INPUT
B5
KNOCK 2
Knock 2
B6
PVBAT
Constant 12v
B7
IVBAT
12v from ECM
B8
LAM1A
Pin6 on LSU4.9 Connector
B9
LAM1B
Pin1 on LSU4.9 Connector
B10
LAM1C
Pin5 on LSU4.9 Connector
B11
LAM1D
Pin2 on LSU4.9 Connector
B12
LAM1HEATER
Pin3 on LSU4.9 Connector
B13
IVBAT
12v from ECM
B14
LAM2A
Pin6 on LSU4.9 Connector
B15
LAM2B
Pin1 on LSU4.9 Connector
B16
LAM2C
Pin5 on LSU4.9 Connector
B17
LAM2D
Pin2 on LSU4.9 Connector
B18
LAM2HEATER
Pin3 on LSU4.9 Connector
B19
IVBAT
Red Wire
B20
KLINE
Alternator Lin
B21
RS232RX / Can L
—
B22
RS232TX / Can H
—
B23
LANRX‐
—
B24
LANRX+
—
B25
LANTX‐
—
B26
LANTX+
—
Connector C
ECU pin
Syvecs description
Application notes
C1
KNOCK GROUND
Knock Ground
C2
ANGND
SENSOR GND
C3
ANGND
Cam and Crank Ground
C4
ANGND
SENSOR GND
C5
5V OUT
5V OUTPUT FOR SENSORS
C6
5V OUT
5V OUTPUT FOR SENSORS
C7
5V OUT
5V OUTPUT FOR SENSORS
C8
CAN L
Merc Can
C9
CAN H
Merc Can
C10
AN01
Cam1 Ex
C11
AN02
Cam2 Ex
C12
AN03
Cam 1
C13
AN04
Cam2
C14
AN05
Crank
C15
AN06
Tps2A
C16
AN07
Tps2B
C17
AN08
Map
C18
AN09
Tps1A
C19
AN10
Tps1B
C20
AN11
PPSA
C21
AN12
PPsB
C22
AN13
COOLANT TEMP INPUT
C23
AN14
AIR TEMP INPUT
C24
AN15
—
C25
AN16
—
C26
EGT1-
—
C27
EGT1+
—
C28
PWR CTR IN
Ignition Sw
C29
AN S1 / Slave An01
Fuel Pressure
C30
AN S2 / Slave An02
Fuel Tank Pressure
C31
AN S3 / Slave An03
—
C32
AN S4 / Slave An04
Oil Temp/Level on SLS
C33
AN S5 / Slave An05
Engine Oil Pressure 2
C34
AN S6 / Slave An06
Oil Temp
Revision 2: Syvecs Mercedes C63 SLS M156 S7Plus Plug-in ECUSyvecs S7Plus general-purpose ECU shown as a family reference; vehicle-specific kit and adaptor may differ. Manufacturer photograph, reproduced with permission. Image source.
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Mercedes C63 SLS M156 S7Plus, with product code S7Plus-M156. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs Mercedes C63 SLS M156 S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
From the Syvecs Mercedes M156/9 installation guide, revision 1.2. The tables list ECU-side pins and the manufacturer's vehicle-specific notes, not the complete original vehicle connectors. A dash denotes a blank field in the source, not proof of an unused circuit. Confirm the ECU, harness revision and connector orientation against the manufacturer document.