
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Mercedes C63 SLS M156 S7Plus, with product code S7Plus-M156. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs Mercedes C63 SLS M156 S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
Sources
- Syvecs Mercedes C63 SLS M156 S7Plus product listing and application
- Manufacturer kit installation and pinout manual
- Syvecs plug-in kit support index
Manufacturer ECU connector schedules
From the Syvecs Mercedes M156/9 installation guide, revision 1.2. The tables list ECU-side pins and the manufacturer's vehicle-specific notes, not the complete original vehicle connectors. A dash denotes a blank field in the source, not proof of an unused circuit. Confirm the ECU, harness revision and connector orientation against the manufacturer document.
Connector A
| ECU pin | Syvecs description | Application notes |
|---|---|---|
| A1 | PWR CTR OUT | Main Relay |
| A2 | H‐Bridge1 / SlaveOut1 | DBW+ |
| A3 | H‐Bridge2 / SlaveOut2 | DBW- |
| A4 | H‐Bridge3 / SlaveOut3 | DBW+ |
| A5 | H‐Bridge4 / SlaveOut4 | DBW- |
| A6 | H‐Bridge5 / SlaveOut5 | Starter |
| A7 | H‐Bridge6 / SlaveOut6 | Intake Manifold Switch Valve |
| A8 | H‐Bridge7 / SlaveOut7 | Oil Cooler Fan |
| A9 | H‐Bridge8 / SlaveOut8 | Water Injection |
| A10 | FUEL1 | CYL 1 INJECTOR |
| A11 | FUEL2 | CYL 2 INJECTOR |
| A12 | FUEL3 | CYL 3 INJECTOR |
| A13 | FUEL4 | CYL 4 INJECTOR |
| A14 | FUEL5 | CYL 5 INJECTOR |
| A15 | FUEL6 | CYL 6 INJECTOR |
| A16 | FUEL7 | CYL 7 INJECTOR |
| A17 | FUEL8 | CYL 8 INJECTOR |
| A18 | PWM1 /*FUEL9 | Heating System Shut off |
| A19 | PWM2 / *FUEL10 | Engine and AC Fan |
| A20 | PWM3 / *FUEL11 | Fuel Pump Relay |
| A21 | PWM4 / *FUEL12 | Coolant Thermostate heating element |
| A22 | PWM5 / *FUEL13 | Vvti 1EX -Flyback Solder Bridge Set |
| A23 | PWM6 / *FUEL14 | Vvti 2Ex -Flyback Solder Bridge Set |
| A24 | PWM7 / *FUEL15 | Vvti 1 -Flyback Solder Bridge Set |
| A25 | PWM8 / *FUEL16 | Vvti 2 -Flyback Solder Bridge Set |
| A26 | IGN1 | Ign 1 & 6 |
| A27 | IGN2 | Ign 2 & 8 |
| A28 | IGN3 | Ign 4 & 7 |
| A29 | IGN4 | Ign 5 & 3 |
| A30 | IGN5 | Fuel Pump Speed |
| A31 | IGN6 | — |
| A32 | PWRGND | Black Wire |
| A33 | PWRGND | ECU GND |
| A34 | PWRGND | ECU GND |
Connector B
| ECU pin | Syvecs description | Application notes |
|---|---|---|
| B1 | PWRGND | PWR GND |
| B2 | CAN2L | — |
| B3 | CAN2H | — |
| B4 | KNOCK | KNOCK SENSOR INPUT |
| B5 | KNOCK 2 | Knock 2 |
| B6 | PVBAT | Constant 12v |
| B7 | IVBAT | 12v from ECM |
| B8 | LAM1A | Pin6 on LSU4.9 Connector |
| B9 | LAM1B | Pin1 on LSU4.9 Connector |
| B10 | LAM1C | Pin5 on LSU4.9 Connector |
| B11 | LAM1D | Pin2 on LSU4.9 Connector |
| B12 | LAM1HEATER | Pin3 on LSU4.9 Connector |
| B13 | IVBAT | 12v from ECM |
| B14 | LAM2A | Pin6 on LSU4.9 Connector |
| B15 | LAM2B | Pin1 on LSU4.9 Connector |
| B16 | LAM2C | Pin5 on LSU4.9 Connector |
| B17 | LAM2D | Pin2 on LSU4.9 Connector |
| B18 | LAM2HEATER | Pin3 on LSU4.9 Connector |
| B19 | IVBAT | Red Wire |
| B20 | KLINE | Alternator Lin |
| B21 | RS232RX / Can L | — |
| B22 | RS232TX / Can H | — |
| B23 | LANRX‐ | — |
| B24 | LANRX+ | — |
| B25 | LANTX‐ | — |
| B26 | LANTX+ | — |
Connector C
| ECU pin | Syvecs description | Application notes |
|---|---|---|
| C1 | KNOCK GROUND | Knock Ground |
| C2 | ANGND | SENSOR GND |
| C3 | ANGND | Cam and Crank Ground |
| C4 | ANGND | SENSOR GND |
| C5 | 5V OUT | 5V OUTPUT FOR SENSORS |
| C6 | 5V OUT | 5V OUTPUT FOR SENSORS |
| C7 | 5V OUT | 5V OUTPUT FOR SENSORS |
| C8 | CAN L | Merc Can |
| C9 | CAN H | Merc Can |
| C10 | AN01 | Cam1 Ex |
| C11 | AN02 | Cam2 Ex |
| C12 | AN03 | Cam 1 |
| C13 | AN04 | Cam2 |
| C14 | AN05 | Crank |
| C15 | AN06 | Tps2A |
| C16 | AN07 | Tps2B |
| C17 | AN08 | Map |
| C18 | AN09 | Tps1A |
| C19 | AN10 | Tps1B |
| C20 | AN11 | PPSA |
| C21 | AN12 | PPsB |
| C22 | AN13 | COOLANT TEMP INPUT |
| C23 | AN14 | AIR TEMP INPUT |
| C24 | AN15 | — |
| C25 | AN16 | — |
| C26 | EGT1- | — |
| C27 | EGT1+ | — |
| C28 | PWR CTR IN | Ignition Sw |
| C29 | AN S1 / Slave An01 | Fuel Pressure |
| C30 | AN S2 / Slave An02 | Fuel Tank Pressure |
| C31 | AN S3 / Slave An03 | — |
| C32 | AN S4 / Slave An04 | Oil Temp/Level on SLS |
| C33 | AN S5 / Slave An05 | Engine Oil Pressure 2 |
| C34 | AN S6 / Slave An06 | Oil Temp |