Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
Haltech standalone ECUs
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Changes from revision 2 to revision 3

Removed text is struck through; added text is highlighted.

Haltech Nexus R5 VCU. Image: Haltech, reproduced with permission.

Haltech Nexus R5 is a programmable vehicle control unit with engine management in Haltech's Nexus family. VCU incorporating power distribution, onboard inertial sensor and four 25 A high-current outputs. Its 18 peak-and-hold injection outputs allow additional injectors in staged installations. Haltech universal comparison.

Identification and I/O

ItemManufacturer comparisonInjector channels18, peak-and-holdIgnition channels12Digital pulsed outputs8MAP sensorExternalTuning softwareNexus Software Programmer (NSP); verify installed firmware

Counts do not imply that all functions are available simultaneously: driver allocation, injector impedance, ignition type, firmware and calibration must suit the installation.

Pinout and wiring

Use the manufacturer wiring diagrams and select the Nexus R5 ECU and actual harness or part number. Drawings for other models and plug-in adaptors are not a substitute for the identified unit. Verify connector orientation, power and grounds, current limits and output assignment before connection.

The full 124-pin assignment of connectors A to E, redrawn from Haltech's wiring diagram revision 2.1 (February 2023), is in Haltech Nexus R5 connector pinout. Main battery positive and ground use two SurLok power terminals rather than connector pins.

Software and further information

Download the matching software and firmware through Haltech downloads. For family context and other models see Haltech standalone ECUs. Compare the label, serial, connectors and map backup before replacing a controller.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 2: Haltech Nexus R5
Haltech Nexus R5 vehicle control unit
Haltech Nexus R5 VCU. Image: Haltech, reproduced with permission.

Haltech Nexus R5 is a programmable vehicle control unit with engine management in Haltech's Nexus family. VCU incorporating power distribution, onboard inertial sensor and four 25 A high-current outputs. Its 18 peak-and-hold injection outputs allow additional injectors in staged installations. Haltech universal comparison.

Identification and I/O

ItemManufacturer comparison
Injector channels18, peak-and-hold
Ignition channels12
Digital pulsed outputs8
MAP sensorExternal
Tuning softwareNexus Software Programmer (NSP); verify installed firmware

Counts do not imply that all functions are available simultaneously: driver allocation, injector impedance, ignition type, firmware and calibration must suit the installation.

Pinout and wiring

Use the manufacturer wiring diagrams and select the Nexus R5 ECU and actual harness or part number. Drawings for other models and plug-in adaptors are not a substitute for the identified unit. Verify connector orientation, power and grounds, current limits and output assignment before connection.

Software and further information

Download the matching software and firmware through Haltech downloads. For family context and other models see Haltech standalone ECUs. Compare the label, serial, connectors and map backup before replacing a controller.

Revision 3: Haltech Nexus R5
Haltech Nexus R5 vehicle control unit
Haltech Nexus R5 VCU. Image: Haltech, reproduced with permission.

Haltech Nexus R5 is a programmable vehicle control unit with engine management in Haltech's Nexus family. VCU incorporating power distribution, onboard inertial sensor and four 25 A high-current outputs. Its 18 peak-and-hold injection outputs allow additional injectors in staged installations. Haltech universal comparison.

Identification and I/O

ItemManufacturer comparison
Injector channels18, peak-and-hold
Ignition channels12
Digital pulsed outputs8
MAP sensorExternal
Tuning softwareNexus Software Programmer (NSP); verify installed firmware

Counts do not imply that all functions are available simultaneously: driver allocation, injector impedance, ignition type, firmware and calibration must suit the installation.

Pinout and wiring

Use the manufacturer wiring diagrams and select the Nexus R5 ECU and actual harness or part number. Drawings for other models and plug-in adaptors are not a substitute for the identified unit. Verify connector orientation, power and grounds, current limits and output assignment before connection.

The full 124-pin assignment of connectors A to E, redrawn from Haltech's wiring diagram revision 2.1 (February 2023), is in Haltech Nexus R5 connector pinout. Main battery positive and ground use two SurLok power terminals rather than connector pins.

Software and further information

Download the matching software and firmware through Haltech downloads. For family context and other models see Haltech standalone ECUs. Compare the label, serial, connectors and map backup before replacing a controller.