
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as Nissan 370Z Manual Auto S7Plus, with product code S7Plus-N370Z. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Wiring and pinout
Syvecs Nissan 370Z Manual Auto S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
Sources
- Syvecs Nissan 370Z Manual Auto S7Plus product listing and application
- Manufacturer kit installation and pinout manual
- Syvecs plug-in kit support index
Manufacturer ECU connector schedules
From the Syvecs Nissan 370Z installation guide, revision 1.2. These are ECU-side connections and the manufacturer's application notes; the guide does not give a complete factory vehicle-connector schedule. For A1, consult the drawing for the diode between the relay pins. Confirm the orientation, loom revision, and configured functions against the manufacturer guide before connecting.
Connector A
| ECU pin | Syvecs description | 370Z application notes |
|---|---|---|
| A1 | PWR CTR OUT | Throttle and main relay; see the manual for the diode between pins 24 and 25 |
| A2 | H‐Bridge1 / SlaveOut1 | DBW |
| A3 | H‐Bridge2 / SlaveOut2 | DBW |
| A4 | H‐Bridge3 / SlaveOut3 | DBW |
| A5 | H‐Bridge4 / SlaveOut4 | DBW |
| A6 | H‐Bridge5 / SlaveOut5 | SPARE |
| A7 | H‐Bridge6 / SlaveOut6 | Fuel Pump Relay |
| A8 | H‐Bridge7 / SlaveOut7 | Evap |
| A9 | H‐Bridge8 / SlaveOut8 | VVEL Signal |
| A10 | FUEL1 | Primary Injector 1 |
| A11 | FUEL2 | Primary Injector 2 |
| A12 | FUEL3 | Primary Injector 3 |
| A13 | FUEL4 | Primary Injector 4 |
| A14 | FUEL5 | Primary Injector 5 |
| A15 | FUEL6 | Primary Injector 6 |
| A16 | FUEL7 | Secondary Injector 1 Or Spare Ouput |
| A17 | FUEL8 | Secondary Injector 2 Or Spare Ouput |
| A18 | PWM1 /*FUEL9 | Secondary Injector 3 Or Spare Ouput |
| A19 | PWM2 / *FUEL10 | Secondary Injector 4 Or Spare Ouput |
| A20 | PWM3 / *FUEL11 | Spare |
| A21 | PWM4 / *FUEL12 | Secondary Injector 5 Or Spare Ouput |
| A22 | PWM5 | Secondary Injector 6 Or Spare Ouput |
| A23 | PWM6 | Tacho |
| A24 | PWM7 | VVT1 |
| A25 | PWM8 | VVT2 |
| A26 | IGN1 | Ignition 1 |
| A27 | IGN2 | Ignition 2 |
| A28 | IGN3 | Ignition 3 |
| A29 | IGN4 | Ignition 4 |
| A30 | IGN5 | Ignition 5 |
| A31 | IGN6 | Ignition 6 |
| A32 | PWRGND | — |
| A33 | PWRGND | — |
| A34 | PWRGND | — |
Connector B
| ECU pin | Syvecs description | 370Z application notes |
|---|---|---|
| B1 | PWRGND | — |
| B2 | CAN2L | — |
| B3 | CAN2H | — |
| B4 | KNOCK | — |
| B5 | KNOCK 2 | — |
| B6 | PVBAT | — |
| B7 | IVBAT | — |
| B8 | LAM1A | 2.2v |
| B9 | LAM1B | 1.8v |
| B10 | LAM1C | — |
| B11 | LAM1D | — |
| B12 | LAM1HEATER | — |
| B13 | IVBAT | — |
| B14 | LAM2A | 2.2v |
| B15 | LAM2B | 1.8v |
| B16 | LAM2C | — |
| B17 | LAM2D | — |
| B18 | LAM2HEATER | — |
| B19 | IVBAT | — |
| B20 | KLINE | — |
| B21 | RS232RX | — |
| B22 | RS232TX | — |
| B23 | LANRX‐ | — |
| B24 | LANRX+ | — |
| B25 | LANTX‐ | — |
| B26 | LANTX+ | — |
Connector C
| ECU pin | Syvecs description | 370Z application notes |
|---|---|---|
| C1 | KNOCKGND | Knock Ground |
| C2 | ANGND | Brake Booster, TPS, Gear Lever |
| C3 | ANGND | Crank, ACT |
| C4 | ANGND | ECT |
| C5 | 5V OUT | TPS, Brake Booster, Gear lever |
| C6 | 5V OUT | Crank |
| C7 | 5V OUT | PPS |
| C8 | CAN L | Can Low |
| C9 | CAN H | Can High |
| C10 | AN01 | TPS 1A |
| C11 | AN02 | TPS 1B |
| C12 | AN03 | TPS 2A |
| C13 | AN04 | TPS2B |
| C14 | AN05 | Cam Position Sensor |
| C15 | AN06 | Crank Position Sensor |
| C16 | AN07 | Cam2 Position Sensor |
| C17 | AN08 | Oil Temp |
| C18 | AN09 | MAP Absolute Sensor |
| C19 | AN10 | PPS1 |
| C20 | AN11 | PPS2 |
| C21 | AN12 | Brake Switch |
| C22 | AN13 | Clutch Sw |
| C23 | AN14 | Air Charge Temp |
| C24 | AN15 | Coolant Temp |
| C25 | AN16 | Cruise Control SW |
| C26 | EGT1- | Flying TC Lead |
| C27 | EGT1+ | Flying TC Lead |
| C28 | PWR CTR IN | Ignition Switch |
| C29 | AN S1 / Slave An01 | Power Steering Pressure |
| C30 | AN S2 / Slave An02 | Maf 1 / Spare Input / |
| C31 | AN S3 / Slave An03 | Maf2 / Spare Input/ |
| C32 | AN S4 / Slave An04 | Brake Booster / |
| C33 | AN S5 / Slave An05 | Gear Lever Position X / DONT REMOVE ON MANUAL |
| C34 | AN S6 / Slave An06 | Gear Lever Position Y / DONT REMOVE ON MANUAL |