Removed text is struck through; added text is highlighted.
Syvecs S7Plus general-purpose ECU shown as a family reference; vehicle-specific kit and adaptor may differ. Manufacturer photograph, reproduced with permission. Image source.
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as BMW E46 M3 S7Plus, with product code S7Plus-BE46. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Confirmed installation details
Manufacturer product code S7Plus-BE46 is listed for the S54 E46 M3 with manual transmission only. The documented package includes an S7Plus, S54 loom adaptor, Ethernet cable and spare pins; optional lambda and MAP kits can be specified. The base map is for an unmodified naturally aspirated engine and must be recalibrated for modifications.
Example from the kit loom schedule: S7 connector A10–A15 map to E46 connector C33–C38 for injectors 1–6; A26 maps to E1 for ignition 1. Verify the loom revision and complete manufacturer table before use.
Wiring and pinout
Syvecs BMW E46 M3 S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
Sources
Syvecs BMW E46 M3 S7Plus product listing and applicationManufacturer kit installation and pinout manualSyvecs plug-in kit support index
Manufacturer ECU connector schedules
From the Syvecs E46 M3 installation guide, revision 1.2. The table gives the Syvecs ECU connector pins and the vehicle-side loom positions listed in the document. A blank means the guide leaves the entry blank; it does not prove the cavity is unused. Confirm the orientation, loom revision, and configured functions against the manufacturer guide before connecting.
Open each version to inspect formatting, tables and photographs.
Revision 2: Syvecs BMW E46 M3 S7Plus Plug-in ECUSyvecs S7Plus general-purpose ECU shown as a family reference; vehicle-specific kit and adaptor may differ. Manufacturer photograph, reproduced with permission. Image source.
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as BMW E46 M3 S7Plus, with product code S7Plus-BE46. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Confirmed installation details
Manufacturer product code S7Plus-BE46 is listed for the S54 E46 M3 with manual transmission only. The documented package includes an S7Plus, S54 loom adaptor, Ethernet cable and spare pins; optional lambda and MAP kits can be specified. The base map is for an unmodified naturally aspirated engine and must be recalibrated for modifications.
Example from the kit loom schedule: S7 connector A10–A15 map to E46 connector C33–C38 for injectors 1–6; A26 maps to E1 for ignition 1. Verify the loom revision and complete manufacturer table before use.
Wiring and pinout
Syvecs BMW E46 M3 S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
From the Syvecs E46 M3 installation guide, revision 1.2. The table gives the Syvecs ECU connector pins and the vehicle-side loom positions listed in the document. A blank means the guide leaves the entry blank; it does not prove the cavity is unused. Confirm the orientation, loom revision, and configured functions against the manufacturer guide before connecting.
Connector A
ECU pin
Syvecs description
E46 loom pin
E46 notes
A1
PWR CTR OUT
B23
Throttle and Main Relay
A2
H‐Bridge1 / SlaveOut1
A2
DBW
A3
H‐Bridge2 / SlaveOut2
A9
DBW
A4
H‐Bridge3 / SlaveOut3
C4
VANOS INLET ADV
A5
H‐Bridge4 / SlaveOut4
C50
VANOS INLET RTD
A6
H‐Bridge5 / SlaveOut5
C44
VANOS EXH ADV
A7
H‐Bridge6 / SlaveOut6
C43
VANOS EXH RTD
A8
H‐Bridge7 / SlaveOut7
—
—
A9
H‐Bridge8 / SlaveOut8
—
—
A10
FUEL1
C33
Primary Injector 1
A11
FUEL2
C34
Primary Injector 2
A12
FUEL3
C35
Primary Injector 3
A13
FUEL4
C36
Primary Injector 4
A14
FUEL5
C37
Primary Injector 5
A15
FUEL6
C38
Primary Injector 6
A16
FUEL7
C47
IDLE OPEN
A17
FUEL8
C46
IDLE CLOSE
A18
PWM1 /*FUEL9
B11, D10
Fuel Pump
A19
PWM2 / *FUEL10
D4
FAN
A20
PWM3 / *FUEL11
D17
Tacho
A21
PWM4 / *FUEL12
—
Secondary Injector 5 Or Spare Ouput
A22
PWM5
—
Secondary Injector 6 Or Spare Ouput
A23
PWM6
D16
Sport LED (Added in V5 Loom)
A24
PWM7
C42
EVAP
A25
PWM8
D29
A/C CLUTCH
A26
IGN1
E1
CYL 1 IGNITION OUTPUT
A27
IGN2
E2
CYL 2 IGNITION OUTPUT
A28
IGN3
E3
CYL 3 IGNITION OUTPUT
A29
IGN4
E9
CYL 4 IGNITION OUTPUT
A30
IGN5
E6
CYL 5 IGNITION OUTPUT
A31
IGN6
E7
CYL 6 IGNITION OUTPUT
A32
PWRGND
A6
PwrGnd
A33
PWRGND
D5
PwrGNd
A34
PWRGND
A5
PwrGNd
Connector B
ECU pin
Syvecs description
E46 loom pin
E46 notes
B1
PWRGND
A4
PWRGROUND
B2
CAN2L
—
—
B3
CAN2H
—
—
B4
KNOCK
C29
—
B5
KNOCK 2
C31
—
B6
PVBAT
—
—
B7
IVBAT
—
—
B8
LAM1A
—
—
B9
LAM1B
—
—
B10
LAM1C
—
—
B11
LAM1D
—
—
B12
LAM1HEATER
—
—
B13
IVBAT
—
—
B14
LAM2A
—
—
B15
LAM2B
—
—
B16
LAM2C
—
—
B17
LAM2D
—
—
B18
LAM2HEATER
—
—
B19
IVBAT
—
—
B20
KLINE
—
—
B21
RS232RX
—
—
B22
RS232TX
—
—
B23
LANRX‐
Orange/White
—
B24
LANRX+
White/Orange
—
B25
LANTX‐
Green/White
—
B26
LANTX+
White/Green
—
Connector C
ECU pin
Syvecs description
E46 loom pin
E46 notes
C1
KNOCKGND
—
—
C2
ANGND
C17, C20, C21, C25
—
C3
ANGND
D7, D12, D38
—
C4
ANGND
—
—
C5
5V OUT
—
—
C6
5V OUT
D9, D14
—
C7
5V OUT
—
—
C8
CAN L
D37
—
C9
CAN H
D36
—
C10
AN01
D21
Oil Level Temp
C11
AN02
C8
Crank Position Sensor
C12
AN03
C23
TPS 1A
C13
AN04
C10
TPS 1B
C14
AN05
C5
Cam Position Sensor
C15
AN06
—
—
C16
AN07
C2
Cam2 EX Position Sensor
C17
AN08
—
—
C18
AN09
External Loom
MAP Absolute Sensor
C19
AN10
D8
PPS1
C20
AN11
D13
PPS2
C21
AN12
D24
Brake Switch
C22
AN13
B10
EGT
C23
AN14
C22
Air Charge Temp
C24
AN15
C24
Coolant Temp
C25
AN16
D39
Coolant Charge Temp (M3)
C26
EGT1‐
—
—
C27
EGT1+
—
—
C28
PWR CTR IN
D26
Ignition Switch
C29
AN S1 / Slave An01
D27
MFL Conn (Added in V5 Loom)
C30
AN S2 / Slave An02
D15
Sport Sw (Added in V5 Loom)
C31
AN S3 / Slave An03
C39
Oil level/Temp
C32
AN S4 / Slave An04
C26
OIL PRESSURE SW
C33
AN S5 / Slave An05
B20
CLUTCH SW
C34
AN S6 / Slave An06
C1
MAF
Revision 2: Syvecs BMW E46 M3 S7Plus Plug-in ECUSyvecs S7Plus general-purpose ECU shown as a family reference; vehicle-specific kit and adaptor may differ. Manufacturer photograph, reproduced with permission. Image source.
Model and vehicle application
Syvecs lists this vehicle-specific standalone or plug-in ECU kit as BMW E46 M3 S7Plus, with product code S7Plus-BE46. The product page and its stated vehicle, model and transmission details define this particular application; confirm market, model year, engine, ECU connector and transmission against Syvecs before ordering.
This entry describes the dedicated vehicle kit. It is distinct from the generic wire-in ECU: a plug-in kit can use application-specific adaptor wiring, a carrier, additional modules and an application calibration. The listed hardware or supported equipment can vary by revision.
Confirmed installation details
Manufacturer product code S7Plus-BE46 is listed for the S54 E46 M3 with manual transmission only. The documented package includes an S7Plus, S54 loom adaptor, Ethernet cable and spare pins; optional lambda and MAP kits can be specified. The base map is for an unmodified naturally aspirated engine and must be recalibrated for modifications.
Example from the kit loom schedule: S7 connector A10–A15 map to E46 connector C33–C38 for injectors 1–6; A26 maps to E1 for ignition 1. Verify the loom revision and complete manufacturer table before use.
Wiring and pinout
Syvecs BMW E46 M3 S7Plus installation and wiring document. Follow the connector orientation, application-specific tables, installation notes and hardware revision in this document. Do not transfer assignments from another vehicle merely because the underlying ECU family is similar. The link was checked to return a PDF.
For other variants and manual revisions consult the manufacturer's vehicle-specific manual index. Available spare inputs and outputs can be used only within their electrical limits and with a matching calibration.
Calibration and service
Use the correct Syvecs software, firmware and base calibration for the exact vehicle and installed hardware. The Syvecs software portal and firmware archive provide manufacturer support. A base map is a starting point and needs checking against the actual engine, injectors, sensors and modifications.
From the Syvecs E46 M3 installation guide, revision 1.2. The table gives the Syvecs ECU connector pins and the vehicle-side loom positions listed in the document. A blank means the guide leaves the entry blank; it does not prove the cavity is unused. Confirm the orientation, loom revision, and configured functions against the manufacturer guide before connecting.