
Link G4X E36X is a vehicle-specific programmable plug-in ECU for the BMW E36 application listed in Link's model-specific manuals index. It is an application board, rather than the universal wire-in ECU. Check the exact vehicle, market, engine, original ECU and board part number against the manufacturer's E36X installation manual.
Identification and installation
Record the Link model label and revision, donor factory ECU connector and car's engine and year. Plug-in boards connect to particular factory-harness layouts; the family or vehicle name alone does not establish every model-year or transmission combination. The manufacturer manual gives the supported application and any installation or configuration notes for this board.
G4X plug-in platforms offer configurable fuel and ignition control but available channels and features depend on the original header and board. The G4X plug-in general specifications are conditional on the particular application and do not mean every input is brought out to the factory harness.
Pinout and tuning
The E36X installation manual is the model-specific source for board pinouts, expansion connections, electrical cautions and startup configuration. Use its connector orientation and the exact board version; do not copy a wire-in ECU pinout onto a factory harness. PCLink and manual downloads; Link manufacturer overview.
Manufacturer connector schedules
From Link's E36X installation manual (2025). The manual states that pinouts are viewed looking into the ECU from the wire side. A dash reproduces an unspecified source field; nc is Link's label. Link marks main-header pins 1 and 38 as sharing Aux 8; injector drives 7 and 8 are not exposed. The 2025 manual identifies the ignition outputs as having internal ignitors. Confirm factory ECU and wiring compatibility for the vehicle.
Main header positions
| Factory pin | Link ECU channel | Factory function |
|---|---|---|
| 1 | Aux 8 (Shared with pin 38) | Fuel Pump Relay |
| 50 | Ign 1 (Internal Ignitor) | Ignition |
| 2 | Aux 1 | Idle Speed Control (Close) |
| 51 | Ign 2 (Internal Ignitor) | Ignition |
| 3 | Injector 5 | Injection |
| 52 | Ign 3 (Internal Ignitor) | Ignition |
| 4 | Injector 6 | Injection |
| 53 | nc | — |
| 5 | Injector 4 | Injection |
| 54 | +14V from Main relay | ECU Power |
| 6 | Ground | — |
| 55 | Ground (Ignition) | — |
| 7 | Aux 3 | Camshaft Solenoid |
| 56 | Ignition Switch | Controls Main Relay |
| 8 | Aux 6 | Check Engine Light |
| 57 | DI 4 | Timing Intervention Request (Transmission Control Module) |
| 9 | nc | — |
| 58 | nc | — |
| 10 | nc | — |
| 59 | +5V Out | — |
| 11 | Aux 7 | Throttle Valve Position (Transmission Control Module) |
| 60 | nc | — |
| 12 | nc | — |
| 61 | nc | — |
| 13 | An Volt 3 | Oxy Sensor |
| 62 | nc | — |
| 14 | nc | — |
| 63 | nc | — |
| 15 | Ground | — |
| 64 | DI 3 | Blower Idle Up |
| 16 | Trig 1 | — |
| 65 | DI 2 | A/C Request |
| 17 | Trig 2 | — |
| 66 | nc | — |
| 18 | nc | — |
| 67 | nc | — |
| 19 | nc | — |
| 68 | nc | — |
| 20 | nc | — |
| 69 | Knock | — |
| 21 | nc | — |
| 70 | Knock | — |
| 22 | nc | — |
| 71 | Ground (Knock) | — |
| 23 | Ign 4 (Internal Ignitor) | Ignition |
| 72 | nc | — |
| 24 | Ign 6 (Internal Ignitor) | Ignition |
| 73 | AnVolt 2 | TPS (Main) |
| 25 | Ign 5 (Internal Ignitor) | Ignition |
| 74 | nc | — |
| 26 | nc (Constant 12V) | — |
| 75 | nc | — |
| 27 | Main Relay Control | — |
| 76 | nc | — |
| 28 | Ground (Shielding) | — |
| 77 | AnTemp 2 | IAT |
| 29 | Aux 2 | Idle Speed Control (Open) |
| 78 | AnTemp 1 | ECT |
| 30 | nc | — |
| 79 | nc | — |
| 31 | Injector 3 | Injection |
| 80 | nc | — |
| 32 | Injector 2 | Injection |
| 81 | DI 5 | Automatic Trans Range Switch (Transmission Control Module) |
| 33 | Injector 1 | Injection |
| 82 | nc | — |
| 34 | Ground | — |
| 83 | nc | — |
| 35 | nc | — |
| 84 | nc | — |
| 36 | Ignition 8 (Aux) | Purge Solenoid |
| 85 | nc | — |
| 37 | nc | — |
| 86 | nc | — |
| 38 | Aux 8 (Shared with pin 1) | O2 Sensor Heater |
| 87 | nc | — |
| 39 | nc | — |
| 88 | nc | — |
| 40 | Ground (O2 sensor) | — |
| 41 | AnVolt 6 | MAF Hot Wire Input (spare) |
| 42 | DI 1 | Speed |
| 43 | Ground (Trigger 1) | — |
| 44 | Ground (Sensors) | — |
| 45 | Ground (Shielding) | — |
| 46 | Aux 4 | Fuel Consumption Signal |
| 47 | Aux 5 | Tachometer |
| 48 | Ignition 7 (Aux) | Air Con Compressor |
| 49 | nc | — |
Expansion connector
| Pin | Link ECU channel | Factory function |
|---|---|---|
| 1 | Gnd | — |
| 2 | +5V Out | — |
| 3 | DI 7 | — |
| 4 | DI 8 | — |
| 5 | AnVolt 5 | — |
| 6 | AnVolt 4 | — |
| 7 | AnTemp 4 | — |
| 8 | AnTemp 3 | — |
Internal sensor
| Position | Link ECU channel | Function |
|---|---|---|
| Internal MAP | AnVolt 1 | MAP |
CAN 1/RS232 Connector
| Pin | Function | Wire colour |
|---|---|---|
| 1 | Comms GND | Brown |
| 2 | CAN1 L | Green |
| 3 | CAN1 H | White |
| 4 | RS232-RX | Grey |
| 5 | RS232-TX | Yellow |
CAN 2/OBD Connector
| Pin | Function | Wire colour |
|---|---|---|
| 1 | GND | Brown |
| 2 | CAN2 L | Green |
| 3 | CAN2 H | White |
| 4 | NC | Grey |
| 5 | +14V | Yellow |