Vi-PEC V Series Nissan S13-S14 is a V Series plug-in ECU documented for Nissan S13–S14 CA18/SR20 long-header applications listed by Link. It is a vehicle-specific replacement board, and the precise model year, engine, ECU connector and market variant must be checked against the installation guide. Link's Vi-PEC manual index.
Installation and pin functions
Use the specific Vi-PEC installation manual for this application. Its installation instructions and pin-function sections identify connections and application differences; a similarly named V Series plug-in board for another vehicle must not be used as a wiring reference. Check the original ECU part number and wiring before fitting.
Programming and support
Link lists Vi-PEC Tuning Software (VTS) for the V Series. Firmware compatibility and the calibration depend on the ECU version. Consult the software archive and retain the original calibration before any change.
Identification limits
This page is indexed by the documented application rather than an independently verified manufacturer SKU. Check the manual for exact compatibility and do not infer additional vehicle fitments.
Manufacturer pinout tables
These are all positions listed in the application-specific Vi-PEC installation guide, page 20. The guide specifies the view looking into the ECU from the wire side. Positions omitted by the guide are not assumed unused; functions must be configured for the vehicle. The manufacturer shows pins 3 and 11 as ignition 3, with pin 11 selectable as ignition 3 or 4 by jumper J1; it also repeats Aux–Inj 5, Aux–Inj 6 and Aux 3 at different pins. Check the board jumper and vehicle-specific loom.
Main ECU connector: documented positions
| Position | ECU function |
|---|---|
| 101 | Injector 1 |
| 34 | DI 1 |
| 103 | Injector 3 |
| 35 | An Volt 2 |
| 106 | Aux – Inj 5 |
| 38 | An Volt 5 |
| 110 | Injector 2 |
| 43 | DI 3 |
| 112 | Injector 4 |
| 46 | DI 4 |
| 113 | Aux 5 |
| 53 | DI 2 |
| 1 | Ignition 1 |
| 55 | An Temp 2 |
| 2 | Ignition 2 |
| 50 | Ground |
| 3 | Ignition 3 |
| 49 | +14V ECCS Relay |
| 4 | Aux – Inj 5 |
| 5 | Aux 1 |
| 6 | Aux – Inj 6 |
| 7 | Aux 2 |
| 8 | Aux 3 |
| 9 | Aux – Inj 6 |
| 11 | Ignition 3 or 4 (J1) |
| 12 | Ignition 4 |
| 18 | Aux 4 |
| 19 | Aux 3 |
| 25 | Aux 6 |
| 27 | An Volt 4 |
| 28 | An Temp 1 |
| 29 | An Volt 1 |
| 32 | Aux 7 |
| 33 | Aux 8 |
| 42, 52 | Trig 1 |
| 41, 51 | Trig 2 |
Other connections
| Position | ECU function |
|---|---|
| Internal MAP | An Volt 3 |
| Expansion 1 | Signal Ground |
| Expansion 2 | +5V Out |
| Expansion 3 | DI 5 |
| Expansion 4 | DI 6 |
| Expansion 5 | - |
| Expansion 6 | An Volt 6 |
| Expansion 7 | - |
| Expansion 8 | An Temp 3 |