Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
Adaptronic standalone ECUs
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Changes from revision 4 to revision 5

Removed text is struck through; added text is highlighted.

Adaptronic eSel008 is a Select-series vehicle plug-in programmable engine-management ECU. The surviving manufacturer guide identifies the intended application as Nissan S13 Silvia / 180SX redtop SR20DET, excluding Type-X. Adaptronic eSel008 application and installation guide.

Identification and application

Confirm the case label and part number, original ECU and loom connector, engine, market and any vehicle-specific equipment against the guide before purchase or installation. Vehicle wiring can vary, and a shared plug shape does not establish pin compatibility.

Software and installation

The Select family uses Adaptronic WARI software, which is listed in Haltech’s legacy Adaptronic downloads archive. Use the matching eSel008 guide and application-specific basemap; the guide documents installation, configuration and pin references. A plug-in ECU still requires configuration and tuning for the actual engine and equipment.

Wiring and pinout

The manufacturer eSel008 guide contains the model and application-specific connector information. Positions and functions can change by application, and factory function and Adaptronic function are separate columns in the guide. The manufacturer connector table is transcribed below; verify the source and viewpoint before use.

Support and sources

Haltech states that Adaptronic operations ended in 2022. Refer to its Adaptronic notice and archived guides, and confirm current support and compatibility for used hardware. A verified product photograph for this exact part has not yet been added.

Adaptronic manufacturer index

Manufacturer connector table

Transcribed from the model-specific Adaptronic installation guide linked above. The guide gives pin numbering from the loom side of the plug, looking into the ECU. A dash denotes a blank source cell. The source says NC is no connection in the factory loom and an empty Adaptronic column means no connection to the Adaptronic ECU. Pin 105 uses an internal jumper; pins 22/30 and 31/40 are paired as noted.

Factory pinFactory functionAdaptronic functionInstallation notes101Injector for cylinder 1Injector Output 3—102Purge valveAux Output 4—103Injector for cylinder 3Injector Output 4—104Fuel pump relayAux Output 5—105Fuel pump voltage controlInternal jumper to select between +5V and GND—106Aircon relayAux Output 7—107GroundPower Ground—108GroundPower Ground—109Constant PowerConst 12VFused battery supply.110Injector for cylinder 2Injector Output 2—111Boost controlAux Output 3—112Injector for cylinder 4Injector Output 1—113Idle Control ValveAux Output 2—114NC——115NC——116GroundPower Ground—1To Igniter for Cylinder 1Ignition output 1—2To Igniter for Cylinder 2Ignition output 4Ignition output 4 precludes auxiliary output 1.3TachometerAux Output 8—4ECCS relayTriggered directly from pin 36 input—5NCDigital input 6External digital input.6GroundPower Ground—7Data link connectorDigital input 7External digital input.8To Igniter for Cylinder 3Ignition output 2—9To Igniter for Cylinder 4Ignition output 3—10Aircon relayAux Output 7—11NCDigital input 4External digital input.12Auto TransmissionDigital input 5External digital input.13GroundPower Ground—14Clock (at CONSULT connector)CAS3Optional flex fuel.15TX (at CONSULT connector)Digital input 8External digital input.16AFM signalMAP signal inputMay accept an external MAP signal.17AFM GNDSensor Ground—18Engine Coolant TemperatureECT signal input—19O2/EGO sensor signalO2/EGO signal input—20Throttle Position SensorTPS signal input—21Sensor groundSensor Ground—22180 deg Cam Angle Sensor SignalCAS 2 inputVariable-width pulses for cylinder and TDC identification.23CHK (at CONSULT connector)0-5V External input—24Malfunction indicator lampAux output 6—25Exhaust temperature warning light——26Exhaust temperatureAux Temperature signal input—27Knock sensor signalKnock input—28Auto Transmission——29Sensor groundSensor Ground—30180 deg Cam Angle Sensor SignalCAS 2 inputLinked to 22.311 deg Cam Angle Sensor SignalCAS 1 inputLinked to 40.32SpeedometerMVSS1Gearbox speed or rear-left wheel speed.33NCMVSS2Optional flex fuel or rear-right speed.34Starter——35Neutral switchDigital Input 1—36Ignition switch+12V Ignition switch, only used to trigger ECCS output—37+5V out+5V outputSensor +5 V supply.38From ECCS relayIgnition power to ECU (from ECCS relay)—39GroundPower Ground—401 deg Cam Angle Sensor SignalCAS 1 inputOne-degree pulses for ignition timing.41Aircon request inputDigital Input 3—42Auto TransmissionSVSS1Optional flex fuel or front-left wheel speed.43Power steering load inputDigital Input 2—44Auto TransmissionSVSS2Optional front-right wheel speed.45Air TemperatureAir Temperature signal input—46Constant PowerNo connection—47From ECCS relay——48GroundPower Ground—

Manufacturer photographAdaptronic eSel008 ECU pictured in its manufacturer installation guide, page 1; reproduced with permission.

Rendered revisions

Open each version to inspect formatting, tables and photographs.

Revision 4: Adaptronic eSel008

Adaptronic eSel008 is a Select-series vehicle plug-in programmable engine-management ECU. The surviving manufacturer guide identifies the intended application as Nissan S13 Silvia / 180SX redtop SR20DET, excluding Type-X. Adaptronic eSel008 application and installation guide.

Identification and application

Confirm the case label and part number, original ECU and loom connector, engine, market and any vehicle-specific equipment against the guide before purchase or installation. Vehicle wiring can vary, and a shared plug shape does not establish pin compatibility.

Software and installation

The Select family uses Adaptronic WARI software, which is listed in Haltech’s legacy Adaptronic downloads archive. Use the matching eSel008 guide and application-specific basemap; the guide documents installation, configuration and pin references. A plug-in ECU still requires configuration and tuning for the actual engine and equipment.

Wiring and pinout

The manufacturer eSel008 guide contains the model and application-specific connector information. Positions and functions can change by application, and factory function and Adaptronic function are separate columns in the guide. The manufacturer connector table is transcribed below; verify the source and viewpoint before use.

Support and sources

Haltech states that Adaptronic operations ended in 2022. Refer to its Adaptronic notice and archived guides, and confirm current support and compatibility for used hardware. A verified product photograph for this exact part has not yet been added.

Adaptronic manufacturer index

Manufacturer connector table

Transcribed from the model-specific Adaptronic installation guide linked above. The guide gives pin numbering from the loom side of the plug, looking into the ECU. A dash denotes a blank source cell. The source says NC is no connection in the factory loom and an empty Adaptronic column means no connection to the Adaptronic ECU. Pin 105 uses an internal jumper; pins 22/30 and 31/40 are paired as noted.

Factory pinFactory functionAdaptronic functionInstallation notes
101Injector for cylinder 1Injector Output 3—
102Purge valveAux Output 4—
103Injector for cylinder 3Injector Output 4—
104Fuel pump relayAux Output 5—
105Fuel pump voltage controlInternal jumper to select between +5V and GND—
106Aircon relayAux Output 7—
107GroundPower Ground—
108GroundPower Ground—
109Constant PowerConst 12VFused battery supply.
110Injector for cylinder 2Injector Output 2—
111Boost controlAux Output 3—
112Injector for cylinder 4Injector Output 1—
113Idle Control ValveAux Output 2—
114NC——
115NC——
116GroundPower Ground—
1To Igniter for Cylinder 1Ignition output 1—
2To Igniter for Cylinder 2Ignition output 4Ignition output 4 precludes auxiliary output 1.
3TachometerAux Output 8—
4ECCS relayTriggered directly from pin 36 input—
5NCDigital input 6External digital input.
6GroundPower Ground—
7Data link connectorDigital input 7External digital input.
8To Igniter for Cylinder 3Ignition output 2—
9To Igniter for Cylinder 4Ignition output 3—
10Aircon relayAux Output 7—
11NCDigital input 4External digital input.
12Auto TransmissionDigital input 5External digital input.
13GroundPower Ground—
14Clock (at CONSULT connector)CAS3Optional flex fuel.
15TX (at CONSULT connector)Digital input 8External digital input.
16AFM signalMAP signal inputMay accept an external MAP signal.
17AFM GNDSensor Ground—
18Engine Coolant TemperatureECT signal input—
19O2/EGO sensor signalO2/EGO signal input—
20Throttle Position SensorTPS signal input—
21Sensor groundSensor Ground—
22180 deg Cam Angle Sensor SignalCAS 2 inputVariable-width pulses for cylinder and TDC identification.
23CHK (at CONSULT connector)0-5V External input—
24Malfunction indicator lampAux output 6—
25Exhaust temperature warning light——
26Exhaust temperatureAux Temperature signal input—
27Knock sensor signalKnock input—
28Auto Transmission——
29Sensor groundSensor Ground—
30180 deg Cam Angle Sensor SignalCAS 2 inputLinked to 22.
311 deg Cam Angle Sensor SignalCAS 1 inputLinked to 40.
32SpeedometerMVSS1Gearbox speed or rear-left wheel speed.
33NCMVSS2Optional flex fuel or rear-right speed.
34Starter——
35Neutral switchDigital Input 1—
36Ignition switch+12V Ignition switch, only used to trigger ECCS output—
37+5V out+5V outputSensor +5 V supply.
38From ECCS relayIgnition power to ECU (from ECCS relay)—
39GroundPower Ground—
401 deg Cam Angle Sensor SignalCAS 1 inputOne-degree pulses for ignition timing.
41Aircon request inputDigital Input 3—
42Auto TransmissionSVSS1Optional flex fuel or front-left wheel speed.
43Power steering load inputDigital Input 2—
44Auto TransmissionSVSS2Optional front-right wheel speed.
45Air TemperatureAir Temperature signal input—
46Constant PowerNo connection—
47From ECCS relay——
48GroundPower Ground—
Revision 5: Adaptronic eSel008

Adaptronic eSel008 is a Select-series vehicle plug-in programmable engine-management ECU. The surviving manufacturer guide identifies the intended application as Nissan S13 Silvia / 180SX redtop SR20DET, excluding Type-X. Adaptronic eSel008 application and installation guide.

Identification and application

Confirm the case label and part number, original ECU and loom connector, engine, market and any vehicle-specific equipment against the guide before purchase or installation. Vehicle wiring can vary, and a shared plug shape does not establish pin compatibility.

Software and installation

The Select family uses Adaptronic WARI software, which is listed in Haltech’s legacy Adaptronic downloads archive. Use the matching eSel008 guide and application-specific basemap; the guide documents installation, configuration and pin references. A plug-in ECU still requires configuration and tuning for the actual engine and equipment.

Wiring and pinout

The manufacturer eSel008 guide contains the model and application-specific connector information. Positions and functions can change by application, and factory function and Adaptronic function are separate columns in the guide. The manufacturer connector table is transcribed below; verify the source and viewpoint before use.

Support and sources

Haltech states that Adaptronic operations ended in 2022. Refer to its Adaptronic notice and archived guides, and confirm current support and compatibility for used hardware. A verified product photograph for this exact part has not yet been added.

Adaptronic manufacturer index

Manufacturer connector table

Transcribed from the model-specific Adaptronic installation guide linked above. The guide gives pin numbering from the loom side of the plug, looking into the ECU. A dash denotes a blank source cell. The source says NC is no connection in the factory loom and an empty Adaptronic column means no connection to the Adaptronic ECU. Pin 105 uses an internal jumper; pins 22/30 and 31/40 are paired as noted.

Factory pinFactory functionAdaptronic functionInstallation notes
101Injector for cylinder 1Injector Output 3—
102Purge valveAux Output 4—
103Injector for cylinder 3Injector Output 4—
104Fuel pump relayAux Output 5—
105Fuel pump voltage controlInternal jumper to select between +5V and GND—
106Aircon relayAux Output 7—
107GroundPower Ground—
108GroundPower Ground—
109Constant PowerConst 12VFused battery supply.
110Injector for cylinder 2Injector Output 2—
111Boost controlAux Output 3—
112Injector for cylinder 4Injector Output 1—
113Idle Control ValveAux Output 2—
114NC——
115NC——
116GroundPower Ground—
1To Igniter for Cylinder 1Ignition output 1—
2To Igniter for Cylinder 2Ignition output 4Ignition output 4 precludes auxiliary output 1.
3TachometerAux Output 8—
4ECCS relayTriggered directly from pin 36 input—
5NCDigital input 6External digital input.
6GroundPower Ground—
7Data link connectorDigital input 7External digital input.
8To Igniter for Cylinder 3Ignition output 2—
9To Igniter for Cylinder 4Ignition output 3—
10Aircon relayAux Output 7—
11NCDigital input 4External digital input.
12Auto TransmissionDigital input 5External digital input.
13GroundPower Ground—
14Clock (at CONSULT connector)CAS3Optional flex fuel.
15TX (at CONSULT connector)Digital input 8External digital input.
16AFM signalMAP signal inputMay accept an external MAP signal.
17AFM GNDSensor Ground—
18Engine Coolant TemperatureECT signal input—
19O2/EGO sensor signalO2/EGO signal input—
20Throttle Position SensorTPS signal input—
21Sensor groundSensor Ground—
22180 deg Cam Angle Sensor SignalCAS 2 inputVariable-width pulses for cylinder and TDC identification.
23CHK (at CONSULT connector)0-5V External input—
24Malfunction indicator lampAux output 6—
25Exhaust temperature warning light——
26Exhaust temperatureAux Temperature signal input—
27Knock sensor signalKnock input—
28Auto Transmission——
29Sensor groundSensor Ground—
30180 deg Cam Angle Sensor SignalCAS 2 inputLinked to 22.
311 deg Cam Angle Sensor SignalCAS 1 inputLinked to 40.
32SpeedometerMVSS1Gearbox speed or rear-left wheel speed.
33NCMVSS2Optional flex fuel or rear-right speed.
34Starter——
35Neutral switchDigital Input 1—
36Ignition switch+12V Ignition switch, only used to trigger ECCS output—
37+5V out+5V outputSensor +5 V supply.
38From ECCS relayIgnition power to ECU (from ECCS relay)—
39GroundPower Ground—
401 deg Cam Angle Sensor SignalCAS 1 inputOne-degree pulses for ignition timing.
41Aircon request inputDigital Input 3—
42Auto TransmissionSVSS1Optional flex fuel or front-left wheel speed.
43Power steering load inputDigital Input 2—
44Auto TransmissionSVSS2Optional front-right wheel speed.
45Air TemperatureAir Temperature signal input—
46Constant PowerNo connection—
47From ECCS relay——
48GroundPower Ground—

Manufacturer photograph

Adaptronic eSel008 Select ECU
Adaptronic eSel008 ECU pictured in its manufacturer installation guide, page 1; reproduced with permission.