Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
Adaptronic standalone ECUs
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Adaptronic eSel022 is a Select-series vehicle plug-in programmable engine-management ECU. The surviving manufacturer guide identifies the intended application as Mazda RX-7 FD Series 8 13B REW twin turbo. Adaptronic eSel022 application and installation guide.

Identification and application

Confirm the case label and part number, original ECU and loom connector, engine, market and any vehicle-specific equipment against the guide before purchase or installation. Vehicle wiring can vary, and a shared plug shape does not establish pin compatibility.

Software and installation

The Select family uses Adaptronic WARI software, which is listed in Haltech’s legacy Adaptronic downloads archive. Use the matching eSel022 guide and application-specific basemap; the guide documents installation, configuration and pin references. A plug-in ECU still requires configuration and tuning for the actual engine and equipment.

Wiring and pinout

The manufacturer eSel022 guide contains the model and application-specific connector information. Positions and functions can change by application, and factory function and Adaptronic function are separate columns in the guide. The manufacturer's connector schedule is reproduced below; use the correct drawing and connector viewpoint rather than borrowing a table from another Select or eMod ECU.

Support and sources

Haltech states that Adaptronic operations ended in 2022. Refer to its Adaptronic notice and archived guides, and confirm current support and compatibility for used hardware. A verified product photograph for this exact part has not yet been added.

Adaptronic manufacturer index

Manufacturer connector table

From the Adaptronic eSel022 installation guide, pages 33–35. These are the manufacturer-listed positions; a blank entry is represented by a dash. NC in the factory column refers to the factory loom, not necessarily an unused Adaptronic input or output. Verify the application and connector orientation in the original guide.

Factory pinFactory functionAdaptronic functionComments
4AEGI Main relay+12V IgnitionWhen this switches to 12V, the EGI main relay is activated
4BBatteryConst 12V—
4CIG SW——
4DA / P relay——
4EDLC (+B) EGI main relay——
4Ffuel pump relay (speed)PGND—
4GCircuit Opening relay / Fuel pump relayAux Output 5—
4HTNS relay——
4IA/C relayAC Relay Output—
4KElectric fan relay no.2 and no.4Aux Output 6—
4LElectric fan relay no.3Aux Output 6—
4MDLC (IG-) PCM engine (rpm signal)Tacho Out—
4ODLC (TEN) PCM engineIgniter Output 4—
4P96-98 (heat warning light) 99- (-)——
4Qspeedometer sensorMVSS1—
4R-——
4SClutch switchDigital Input 1—
4U-——
4VA/C switchDigital Input 4—
4WP / S pressure switchDigital Input 3—
4YDLC (MEN) PCM engineCAS3Flex fuel sensor input
4AAStoplight switchDigital Input 5—
4ABA / C Amplifier——
4ACParking lightDigital input 8—
4AERear defroster——
4AFIgniter IGT - TFIgniter Output 2—
4AGA/C Thermoswitch——
4AHMAP / boost sensorMAP signal inputThere is already a MAP sensor on the engine
4AIDLC (FEN) PCM engine——
4AJIgniter IGT - TRIgniter Output 3—
4AK-MVSS2—
4AL-SVSS1—
4AM-SVSS2—
4ANIgniter IGT-LIgniter Output 1—
3ATPS constantTPS 5V—
3Bß——
3CNeutral switchDigital Input 2—
3DO2 sensorO2 signal input—
3E-Digital input 6—
3F-Digital input 7—
3Gfuel pressure regulator solenoid——
3Hoil metering pump sensorExt In—
3ITPS (full range)TPS signal input—
3KTPS (narrow range)——
3M-——
3OKnock sensorKnock input—
3QDouble throttle control solenoid——
3RCrank angle sensor (Ne+)CAS 1 input—
3SCrank angle sensor (G-)SGND—
3TIntake air temperature sensorMAT input—
3UCrank angle sensor (G+)CAS 2 input—
3VFuel temperature sensorAux TempThis is not used by the ECU for tuning. Therefore it can be used for oil temerature input for logging or a race dash.
3WWater temperature sensorECT—
3X-——
3Z-——
3ABGround (input)SGND—
1A-——
1B-——
1CIdle speed control solenoidAux Output 2—
1DPort Air control solenoid——
1ECharge control solenoidInverse Aux output 4—
1FSecondary air relief/bypass valve——
1GPurge control solenoid——
1HElectric fan relay No.1Aux Output 6—
1ICharge relief solenoidAux Output 4—
1KTurbo pre-control solenoidAux Output 1—
1LGround (CPU)PGND—
1MTurbo control solenoidAux Output 4—
1OWastegate control solenoidAux Output 3—
1QInjector (FP)Injector Output 1—
1R-——
1SStepping motor 1 metering oil pumpAux Output 7—
1UInjector (RP)Injector Output 3—
1WStepping motor 2 metering oil pumpAux Output 8—
1XGround (output)PGND—
1YInjector (FS)Injector Output 2—
1AAStepping motor 3 metering oil pumpAux Output 7 bar—
1ABGround (output)PGND—
1ACInjector (RS)Injector Output 4—
1AD-——
1AEStepping motor 4 metering oil pumpAux Output 8 bar—
1AFGround (output)PGND—
1AH-——
1AJGround (output)PGND—