Adaptronic eSel027 is a Select-series vehicle plug-in programmable engine-management ECU. The surviving manufacturer guide identifies the intended application as Nissan Skyline R34 GTT RB25DET. Adaptronic eSel027 application and installation guide.
Identification and application
Confirm the case label and part number, original ECU and loom connector, engine, market and any vehicle-specific equipment against the guide before purchase or installation. Vehicle wiring can vary, and a shared plug shape does not establish pin compatibility.
Software and installation
The Select family uses Adaptronic WARI software, which is listed in Haltech’s legacy Adaptronic downloads archive. Use the matching eSel027 guide and application-specific basemap; the guide documents installation, configuration and pin references. A plug-in ECU still requires configuration and tuning for the actual engine and equipment.
Wiring and pinout
The manufacturer eSel027 guide contains the model and application-specific connector information. Positions and functions can change by application, and factory function and Adaptronic function are separate columns in the guide. The manufacturer connector table is transcribed below; verify the source and resistor configuration before use.
Support and sources
Haltech states that Adaptronic operations ended in 2022. Refer to its Adaptronic notice and archived guides, and confirm current support and compatibility for used hardware. A verified product photograph for this exact part has not yet been added.
Manufacturer connector table
From the Adaptronic eSel027 installation guide, pages 18–22. These are the manufacturer-listed positions; a blank entry is represented by a dash. NC in the factory column refers to the factory loom, not necessarily an unused Adaptronic input or output. Verify the application and connector orientation in the original guide. Pin 111 has a resistor-selectable connection: the guide describes R9 or R11, so confirm the board configuration.
| Factory pin | Factory function | Adaptronic function | Comments |
|---|---|---|---|
| 101 | Injector No. 1 cylinder drive signal | Injector Output 2 | Injectors for Cylinders 1 and 4 are paired |
| 102 | NC | - | - |
| 103 | Injector No. 3 cylinder drive signal | Injector Output 3 | Injectors for Cylinders 3 and 5 are paired |
| 104 | Variable air intake control solenoid valve control signal [RB25DE (L/B), RB25DE] Turbo pressure control solenoid valve controls [RB25DET] | Aux Output 2 | — |
| 105 | Injector No. 2 cylinder drive signal | Injector Output 1 | Injectors for Cylinders 2 and 6 are paired |
| 106* | Line pressure solenoid valve control signal | - | - |
| 107 | Air jet swirl control solenoid valve control signal [ RB20DE (L/B)] | - | - |
| 108 | Canister purge control valve control signal | - | - |
| 109 | Control unit power supply (Counter- electromotive current feedback circuit) | Const 12V | Straight from battery via fuse |
| 110 | Injector No. 5 cylinder drive signal | Injector Output 3 | Injectors for Cylinders 3 and 5 are paired |
| 111 | Fuel pump terminal voltage control output signal [RB25DET] | +5V output | Connected to TPS5V via R9 (0R) or to SGND by populating R11 with 0R |
| 112 | Injector No. 6 cylinder drive signal | Injector Output 1 | Injectors for Cylinders 2 and 6 are paired |
| 113* | Line pressure solenoid valve control signal (Dropping resistor circuit) | - | - |
| 114 | Injector No. 4 cylinder drive signal | Injector Output 2 | Injectors for Cylinders 1 and 4 are paired |
| 116 | Injector ground | Power Ground | — |
| 117 | Variable timing control solenoid valve control signal | Aux Output 3 | — |
| 118 | Heated oxygen sensor heater control signal | Power Ground | Connected straight to ground |
| 119* | Power indicator lamp | - | - |
| 120* | Lockup solenoid valve control signal | - | - |
| 121* | Shift solenoid valve A control signal | - | - |
| 122* | Shift solenoid valve B control signal | - | - |
| 123 | NC | - | - |
| 124 | Injector ground | Power Ground | — |
| 1 | To Igniter for Cylinder 1 | Ignition output 1 | Plugs for Cylinders 1 and 6 are fired together in wasted spark |
| 2 | To Igniter for Cylinder 5 | Ignition output 2 | Plugs for Cylinders 2 and 5 are fired together in wasted spark |
| 3 | To Igniter for Cylinder 3 | Ignition output 3 | Plugs for Cylinders 3 and 4 are fired together in wasted spark |
| 4 | ECM & IGN Coil Relay Control Signal | — | When pin 24 has 12V, this pin is pulled low to activate the ECM & IGN coil relay |
| 5 | Tacho out | Aux Output 6 | — |
| 6 | NC | - | - |
| 7 | To Igniter for Cylinder 6 | Ignition output 1 | Plugs for Cylinders 1 and 6 are fired together in wasted spark |
| 8 | To Igniter for Cylinder 2 | Ignition output 2 | Plugs for Cylinders 2 and 5 are fired together in wasted spark |
| 9 | To Igniter for Cylinder 4 | Ignition output 3 | Plugs for Cylinders 3 and 4 are fired together in wasted spark |
| 10 | NC | - | - |
| 11 | AAC valve control signal | Aux Output 1 | — |
| 12 | NC | - | - |
| 13 | Fuel pump relay | Aux Output 5 | — |
| 14 | Air conditioner control signal | Aux Output 4 | — |
| 15 | NC | - | - |
| 16 | NC | - | - |
| 17 | Malfunction indicator lamp | Aux Output 7 | The Adaptronic leaves this off at all times by default, but this can be changed |
| 18 | NC | - | - |
| 19 | NC | - | - |
| 20 | Ignition switch (START) signal | - | - |
| 21 | Air conditioner switch signal | Digital Input 2 | - |
| 22 | Check (Diagnosis Start) | - | - |
| 23 | Throttle sensor output signal | TPS signal | Connected to pin 37 |
| 24 | Ignition switch (IGN) signal | +12V Ignition | When this switches to 12V, the ECM & IGN coil relay is activated (see pin 4) |
| 25 | Control Unit Ground | Power Ground | — |
| 26 | Power steering oil pressure switch signal | Digital Input 1 | — |
| 27 | NC | - | - |
| 28 | SB (select bit) 1 signal | - | - |
| 29 | Vehicle speed sensor signal (Vehicle speed sensor 2) | MVSS1 | — |
| 30 | Headlamp switch signal | Digital Input 3 | — |
| 31 | Ignition power supply | - | - |
| 32 | Control Unit Ground | Power Ground | — |
| 33* | Idle position switch signal | - | - |
| 34* | "1" position switch signal | - | - |
| 35* | "2" position switch signal | - | - |
| 36 | NC | - | - |
| 37 | Throttle opening signal [RB25DE-4WD M/T, RB25DE A/T, RB25DET] | TPS output signal | Connected to pin 23 |
| 38* | "0" position switch signal | - | - |
| 39 | Neutral signal (Park/neutral position signal) | Digital Input 5 | — |
| 40* | "R" position switch signal | - | - |
| 41* | Full switch signal | - | - |
| 42 | NC | - | - |
| 43 | Sensor ground | Sensor Ground | — |
| 44 | Crankshaft position sensor 120 deg (REF) signal | CAS 2 input | Connected to pin 45 |
| 45 | Crankshaft position sensor 120 deg (REF) signal | CAS 2 input | Variable-width pulses each period, for cylinder and TDC identification |
| 46 | Crankshaft position sensor 1 deg (POS) signal | CAS 1 input | 1 degree pulses for calculating ignition timing |
| 47 | Ring gear crankshaft position sensor signal [RB20DE (L/B)] Turbo pressure sensor signal [RB25DET] | MAP signal input | Turbo pressure is connected to the external MAP sensor input (can be disconnected by removing R8) |
| 48 | Power supply for throttle position sensor, refrigerant pressure sensor, and turbo pressure sensor | +5V output | +5V power supply for sensors |
| 49 | Rear defogger switch signal | Digital Input 4 | — |
| 50 | Heated oxygen sensor signal | O2/EGO signal input | For the GTR, this is the front O2/EGO sensor |
| 51 | Throttle motor sensor signal [RB25DET] | - | - |
| 52 | SB (select bit) 2 signal [RB25DET A/T] | - | - |
| 53 | Motor throttle switch signal [RB25DET] | - | - |
| 54 | Mass airflow sensor signal | MAP signal input | AFM signal pin can be used for MAP signal when fitting an external MAP sensor, populate R10 with 0R (not populated by default) |
| 55 | Mass airflow sensor ground | Sensor Ground | — |
| 56 | Engine coolant temperature sensor signal | ECT signal input | — |
| 57 | Refrigerant pressure sensor signal | Spare | — |
| 58* | Output shaft rotation sensor signal (Vehicle speed sensor 1) | - | - |
| 59 | Turbine sensor signal [RB25DET A/T] | - | - |
| 60 | Oil temperature sensor signal | - | - |
| 61 | NC | - | - |
| 62 | Knock sensor signal 1 | Knock input | Both knock sensors are connected to the one knock input |
| 63 | Knock sensor signal 2 | Knock input | Both knock sensors are connected to the one knock input |
| 64 | A/T mode switch signal (POWER) [RB20DE (L/B) A/T] | - | - |
| 65 | DB (data bush 1 signal [RB25DET A/T] | - | - |
| 66 | DB (data bush 3 signal [RB25DET A/T] | - | - |
| 67 | Control unit power supply | - | - |
| 68* | O/D Off indicator lamp | - | - |
| 69 | DB (data bush 2 signal [RB25DET A/T] | - | - |
| 70 | A/T mode switch signal (SNOW) [RB20DE (L/B) A/T] | - | - |
| 71* | Stop lamp switch signal | - | - |
| 72 | Control unit power | - | - |
| 73 | NC | - | - |
| 74 | NC | - | - |
| 75 | Receive (Data input to control unit) | CAS 3 | CAS 3 for flex fuel sensor input |
| 76 | Transmit (Data output to control unit) | MAT | Air temperature sensor input |
| 77 | NC | - | - |
| 78 | Auxiliary electric fan relay control signal [RB25DE, RB25DET] | Aux Output 8 | — |
| 79 | ECM TCM, TCS/ABS integrated control signal ] Multiple communication] [RB25DE A/T, RB25DET | - | - |
| 80 | Battery power supply | - | - |