Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Reference hub
Subject
Engine ECU
Parent
Adaptronic standalone ECUs
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
None

Adaptronic eSel002 is a Select-series vehicle-specific programmable interceptor ECU that works alongside the retained factory ECU. The surviving manufacturer guide identifies the intended application as Mazda RX-8 Series 1 (2003–2008) 13B-MSP and non-MSP RENESIS. Adaptronic eSel002 application and installation guide.

Identification and application

Confirm the case label and part number, original ECU and loom connector, engine, market and any vehicle-specific equipment against the guide before purchase or installation. Vehicle wiring can vary, and a shared plug shape does not establish pin compatibility.

Software and installation

The Select family uses Adaptronic WARI software, which is listed in Haltech’s legacy Adaptronic downloads archive. Use the matching eSel002 guide and application-specific basemap; the guide documents installation, configuration and pin references. A plug-in ECU still requires configuration and tuning for the actual engine and equipment.

Wiring and pinout

The manufacturer eSel002 guide contains the model and application-specific connector information. Positions and functions can change by application, and factory function and Adaptronic function are separate columns in the guide. The manufacturer connector and header tables are transcribed below; verify the source and viewpoint before use.

Support and sources

Haltech states that Adaptronic operations ended in 2022. Refer to its Adaptronic notice and archived guides, and confirm current support and compatibility for used hardware. A verified product photograph for this exact part has not yet been added.

Adaptronic manufacturer index

Manufacturer connector schedules

Transcribed from the Adaptronic eSel002 installation guide. This interceptor retains the factory ECU. The column headed ‘Still connected to factory ECU?’ identifies circuits that are factory-only or shared with both ECUs. The source gives numbering from the loom side, looking into the ECU. The headers are inside the ECU. In the vehicle-connector tables, “NC” is the source's designation for no factory loom connection; a blank Adaptronic entry means no connection to the Adaptronic ECU. A dash in the table reproduces a blank source field.

Factory vehicle connectors: RX-8 Series 1

Factory pinFactory functionAdaptronic functionStill connected to factory ECU?Comments
1ANC———
1BDrive-By-Wire throttle control—Yes—
1CDrive-By-Wire throttle control—Yes—
1DSSV switch—Yes—
1ENC———
1FKnock sensor -—Yes—
1GKnock sensor shield—Yes—
1HNC———
1JThrottle position sensor 1—Yes—
1KNC———
1LSSV solenoid valveAux Output 4NoSecondary Side Valve
1MThrottle position sensor 2—Yes—
1NNC———
1OAir solenoid valve—Yes—
1QThrottle Position Sensor power—Yes—
1RNC———
1SAPV position sensor power—Yes—
1TKnock sensor +Knock signal inputYes, shared with both ECUs—
1USensor groundSensor GroundYes, shared with both ECUs—
1VFront O2 sensor heater—Yes—
1WVDI solenoid valveAux Output 3NoVariable Dynamic Intake
1XNC———
2ARear O2 sensor heater—Yes—
2BO2 sensor ground—Yes—
2CFront O2 sensor signal—Yes—
2DRear (Rotor 2) secondary injectorInjector Output 4NoSecondary injectors for rotors 1 and 2 fire together
2EOil Pressure switch—Yes—
2FThrottle Position Sensor ground—Yes—
2GFront (Rotor 1) secondary injectorInjector Output 4NoSecondary injectors for rotors 1 and 2 fire together
2HSensor shields—Yes—
2IGenerator control—Yes—
2JRear (Rotor 2) primary injector 1Injector Output 3No—
2KEngine Coolant Temperature sensorECT signal inputYes, shared with both ECUs—
2MFront (Rotor 1) primary injector 1Injector Output 1No—
2NOil Metering Pump switch—Yes—
2ONeutral switchDigital Input 2Yes, shared with both ECUs—
2PPurge solenoid valve—Yes—
2QRear O2 sensor signalO2/EGO signal inputYes, shared with both ECUs—
2ROil Level switch—Yes—
2TGenerator control—Yes—
2UEccentric shaft position sensor +CAS 1 inputYes, shared with both ECUsReluctor trigger for ignition timing
2VOil Metering Pump—Yes—
2WOil Metering Pump—Yes—
2XEccentric shaft position sensor -—Yes—
2YOil Metering Pump—Yes—
2ZRear (Rotor 2) leading ignitionIgnition output 4NoAux Output 1 cannot be used due to the fourth ignition output
2AAFront (Rotor 1) leading ignitionIgnition output 1No—
2ABOil Metering Pump—Yes—
2ACRear (Rotor 2) trailing ignitionIgnition output 3No—
2ADFront (Rotor 1) trailing ignitionIgnition output 2No—
3AFront (Rotor 1) primary 2 injectorInjector Output 2NoThe Adaptronic ECU fires both primary 2 injectors together
3BAPV position sensor0-5V Ext/Spare inputYes—
3CNC———
3DRear (Rotor 2) primary 2 injectorInjector Output 2NoThe Adaptronic ECU fires both primary 2 injectors together
3ENC———
3FNC———
3GAPV motor controlControlled by Aux Output 7 via additional high current circuitry inside the Adaptronic ECUNoAuxiliary Port Valve
3H————
3I————
3JAPV motor controlControlled by Aux Output 8 via additional high current circuitry inside the Adaptronic ECUNoAuxiliary Port Valve
3KNC———
3MNC———
3NNC———
3ONC———
3PNC———
3QNC———
3RNC———
4AGroundPower GroundYes, shared with both ECUs—
4BNC———
4CPower from Drive-By- Wire relay—Yes—
4DNC———
4EMain Relay enable—Yes—
4FClutch switchDigital Input 1Yes, shared with both ECUs—
4HNC———
4INC———
4JGroundPower GroundYes, shared with both ECUs—
4KBarometric sensor power—Yes—
4LNC———
4MFuel pump speed control—Yes—
4NNC———
4OAir pump relay—Yes—
4PBrake switch—Yes—
4QIgnition switch+12V IgnitionYes, shared with both ECUs—
4SCAN low—Yes—
4TCoolant Level switch—Yes—
4USensor ground—Yes—
4VCAN high—Yes—
4WHigh/Low A/C control—Yes—
4XAPP sensor power 2—Yes—
4YAPP sensor power 1—Yes—
4ZMedium A/C control—Yes—
5AStarter—Yes—
5BNC———
5CAPP sensor 2—Yes—
5DGroundPower GroundYes, shared with both ECUs—
5ENC———
5FAPP sensor 1Aux temp inputYes—
5HDrive-By-Wire relay—Yes—
5INC———
5JConstant power—Yes—
5KIntake air temperature sensorAir Temp signal inputYes, shared with both ECUs—
5LFuel pump relay—Yes—
5MNC———
5NAir flow meter signalMAP signal inputYes, shared with both ECUsAFM signal pin can be used for MAP signal when fitting an external MAP sensor
5OGroundPower GroundYes, shared with both ECUs—
5PFuel pump relay—Yes—
5RGroundPower GroundYes, shared with both ECUs—
5SBarometric pressure sensor—Yes—
5TGroundPower GroundYes, shared with both ECUs—
5UIntake air temperature sensor ground—Yes—
5VCruise control switch—Yes—
5WA/C amplifier—Yes—
5XCooling fan relay 1—Yes—
5ZVFAD solenoid valveAux Output 2NoVariable Fresh Air Duct
5AAAircon relay—Yes—
5ABAPP sensor ground 2—Yes—
5ACPower from Main Relay—Yes—
5ADCooling fan relays 2 and 3—Yes—
5AEAPP sensor ground 1—Yes—
5AFPower from Main Relay—Yes—
5AGNC———
5AHNC———

Internal 8-pin header

Header pinDescriptionComments
1Sensor 5V supply—
2Sensor Ground—
3MAP signalConnected to the Air Flow Meter signal pin (pin 5N)
4Air Temperature signalConnected to pin 5K
5MVSS1 (master vehicle speed sensor 1)—
6MVSS2 (master vehicle speed sensor 2)—
7SVSS1 (slave vehicle speed sensor 1)—
8SVSS2 (slave vehicle speed sensor 2)—

Internal 6-pin header

Header pinDescriptionComments
1CAS3Can be used for flex fuel sensor input
2Aux Temperature signalTemperature sensors must be wired with one wire to sensor ground and the other wire to the ECU signal input
3Aux Output 5Low current, only suitable for low current loads such as relay coils
4Aux Output 6Low current, only suitable for low current loads such as relay coils
5Digital Input 7—
6Digital Input 8—