Adaptronic eSel010 is a Select-series vehicle plug-in programmable engine-management ECU. The surviving manufacturer guide identifies the intended application as Nissan S14 Silvia / 200SX SR20DET and S13 CA18DET applications. Adaptronic eSel010 application and installation guide.
Identification and application
Confirm the case label and part number, original ECU and loom connector, engine, market and any vehicle-specific equipment against the guide before purchase or installation. Vehicle wiring can vary, and a shared plug shape does not establish pin compatibility.
Software and installation
The Select family uses Adaptronic WARI software, which is listed in Haltech’s legacy Adaptronic downloads archive. Use the matching eSel010 guide and application-specific basemap; the guide documents installation, configuration and pin references. A plug-in ECU still requires configuration and tuning for the actual engine and equipment.
Wiring and pinout
The manufacturer eSel010 guide contains the model and application-specific connector information. Positions and functions can change by application, and factory function and Adaptronic function are separate columns in the guide. The manufacturer connector table is transcribed below; verify the source and viewpoint before use.
Support and sources
Haltech states that Adaptronic operations ended in 2022. Refer to its Adaptronic notice and archived guides, and confirm current support and compatibility for used hardware. A verified product photograph for this exact part has not yet been added.
Manufacturer connector schedules
Transcribed from the Adaptronic eSel010 installation guide. Compare the application-specific descriptions, and configure the internal jumper for the relevant ignition output. The source gives numbering from the loom side, looking into the ECU. In the vehicle-connector tables, “NC” is the source's designation for no factory loom connection; a blank Adaptronic entry means no connection to the Adaptronic ECU. A dash in the table reproduces a blank source field.
Factory connector positions: S14 SR20DET / S13 CA18DET
| Factory pin | Factory function | Adaptronic function | Comments |
|---|---|---|---|
| 101 | Injector for Cylinder 1 | Injector Output 3 | — |
| 102 | Purge Valve | — | — |
| 103 | Injector for Cylinder 3 | Injector Output 4 | — |
| 104 | NC | — | — |
| 105 | NC | — | — |
| 106 | Idle Control Valve (CA18) | Aux output 2 | — |
| 107 | Ground | Power Ground | — |
| 108 | Ground | Power Ground | — |
| 109 | Constant Power | Const 12V | Straight from battery via fuse |
| 110 | Injector for Cylinder 2 | Injector Output 2 | — |
| 111 | NC | — | — |
| 112 | Injector for Cylinder 4 | Injector Output 1 | — |
| 113 | Valve Timing Control solenoid (SR20) | Aux Output 4 | — |
| 114 | NC | — | — |
| 115 | O2 sensor heater ground | Power Ground | — |
| 116 | Ground | Power Ground | — |
| 1 | To Igniter for Cylinder 1 | Ignition output 1 | — |
| 2 | To Igniter for Cylinder 2 | Ignition output 4 | Aux Output 1 cannot be used due to the fourth ignition output |
| 3 | To Igniter for Cylinder 3 (CA18) | Ignition output 2 | — |
| 4 | Idle Control Valve (SR20) | Aux Output 2 | — |
| 5 | Auto Transmission | — | — |
| 6 | Air conditioner output (CA18) | — | — |
| 7 | Tacho out | Aux Output 8 | — |
| 8 | NC | Digital Input 5 | Available as external input |
| 9 | Aircon relay (SR20) | Aux Output 7 | — |
| 10 | Ground | Power Ground | — |
| 11 | Igniter for Cyl 3 (SR20), Cyl 4 (CA18) | Ignition output 2 or 3 | Internal jumper to select input |
| 12 | To Igniter for Cylinder 4 (SR20) | Ignition output 3 | — |
| 13 | NC | — | — |
| 14 | Auto Transmission | — | — |
| 15 | Auto Transmission | — | — |
| 16 | ECCS relay | — | When pin 45 has 12V, this pin is pulled low to activate the ECCS main relay |
| 17 | NC | Aux Temp input | — |
| 18 | Fuel pump relay | Aux Output 5 | — |
| 19 | Cooling fan relay 1 | Aux Output 6 | Internally connected to aux output 6 to run at full speed. |
| 20 | Ground | Power Ground | — |
| 21 | Data link connector | Digital Input 6 | Available as external input |
| 22 | Data link connector | Digital Input 7 | Available as external input |
| 23 | Knock sensor signal | Knock input | — |
| 24 | NC | Digital Input 8 | — |
| 25 | Boost control | Aux Output 3 | — |
| 26 | Air Flow Meter | — | — |
| 27 | Air Flow Meter | — | — |
| 28 | Engine Coolant Temperature | ECT signal input | — |
| 29 | O2/EGO sensor signal | O2/EGO signal input | 0-1V sensor input. Max 3V |
| 30 | Sensor ground | Sensor Ground | — |
| 31 | Data link connector | CAS 3 input | Available as flex fuel input |
| 32 | Malfunction indicator lamp | — | — |
| 33 | Cooling fan relay 2 | Aux Output 6 | — |
| 34 | Power steering load input | Digital Input 2 | — |
| 35 | Factory MAP sensor signal | MAP signal input | On some cars there is already a MAP sensor on the engine, called 'Boost Pressure Sensor'. We recommend using the 4 bar internal MAP sensor on the ECU |
| 36 | NC | Air temp input | Not connected from factory, but can be used as an air temp input |
| 37 | NC | External 0-5V input | — |
| 38 | TPS signal | TPS signal input | — |
| 39 | NC | SVSS 1 | Front left wheel speed, also available as flex fuel input |
| 40 | NC | SVSS 2 | Front right wheel speed input |
| 41 | 180 deg Cam Angle Sensor Signal | CAS 2 input | Variable-width pulses each period, for cylinder and TDC identification |
| 42 | 1 deg Cam Angle Sensor Signal | CAS 1 input | 1 degree pulses for calculating ignition timing |
| 43 | Starter | — | — |
| 44 | Neutral switch | Digital Input 1 | — |
| 45 | Ignition switch | +12V Ignition | When this switches to 12V, the ECCS main relay is activated (see pin 16) |
| 46 | Aircon request input | Digital Input 3 | — |
| 47 | Data link connector | — | — |
| 48 | +5V out | +5V output | +5V power supply for sensors |
| 49 | Power from ECCS relay | — | — |
| 50 | Ground | Power Ground | — |
| 51 | 180 deg Cam Angle Sensor Signal | CAS 2 input | Connected to pin 41 |
| 52 | 1 deg Cam Angle Sensor Signal | CAS 1 input | Connected to pin 42 |
| 53 | Speedometer | MVSS1 | Gearbox speed sensor, or rear left wheel speed input |
| 54 | Rear window defogger load input | Digital Input 4 | — |
| 55 | NC | MVSS2 | Available as rear right wheel speed input or flex fuel input |
| 56 | Auto Transmission | — | — |
| 57 | NC | — | — |
| 58 | Constant Power | — | — |
| 59 | Power from ECCS relay | — | — |
| 60 | Ground | Power Ground | — |