Tuning Wiki

This is a historical revision. Read the current page or return to its history.

Page organisation in this revision
Page type
Technical article
Subject
CAN bus
Parent
Section level
Applies to
No ECU-specific applicability
Tool groups
None
Manufacturers
Abarth, Fiat

Fiat, Abarth, and Alfa Romeo compact platforms from the mid-2000s onward (Grande Punto, Punto Evo, Fiat 500 / 500 Abarth, 500L, 500X, Doblò 263, MiTo, and Giulietta) split vehicle communications across two CAN buses directly accessible on the OBD-II connector:

  • C-CAN (Powertrain / Chassis CAN): 500 kbit/s on OBD-II pins 6 (CAN+) and 14 (CAN−) using 29-bit extended identifiers — connects Engine ECU (Magneti Marelli IAW / Bosch ME/MED/EDC), ABS/ESP, Electric Power Steering (EPS), and BCM.
  • B-CAN (Body CAN): 50 kbit/s fault-tolerant CAN on OBD-II pins 1 (B-CAN+) and 9 (B-CAN−) (requires an ELM327 yellow adapter or dedicated fault-tolerant transceiver) — connects Body Computer, climate control, instrument cluster, doors, and Blue&Me.

Note: For FCA Giorgio (Giulia / Stelvio) and Chrysler/RAM/Jeep CUSW CAN IDs, see Chrysler, Dodge, Jeep, RAM, Fiat and Alfa Romeo CAN bus IDs.

Fiat 500 / Abarth & Grande Punto 29-Bit C-CAN Broadcast IDs (500 kbit/s)

Compiled from community reverse-engineered logs of Fiat 500 (1.2 / Abarth) and Grande Punto (199). Byte indices are 0-based.

Hex ID (29-bit) Decimal System / Signals & Decoding
0x0218A00635168262Wheel Speeds (ABS): Four 16-bit wheel speeds (bytes 0–1, 2–3, 4–5, 6–7), encoded as Speed1 (whole km/h / high byte) + Speed2 (decimal digit / low byte); reads 00 2C per wheel below ~4 km/h
0x0618A001102277121Engine RPM & Pedal (ECM): Bytes 2–3 (big-endian) Engine RPM (1 rpm/bit); Byte 7 Accelerator pedal
0x0628A001103325697Throttle & Clutch: Byte 4 throttle position counts; Byte 5 clutch/accel state (0x00 released, 0x20 clutch depressed)
0x0810A000135307264Brake pressure / pedal force: Byte 2 rises with brake force (0x1x released, 0x3x light, 0x7x normal/hard)
0x0A18A000169385984BCM status bitfields: Byte 0 bit 5 handbrake on; Byte 2 bit 3 left front door open, bit 6 contact, bit 7 ignition; Byte 4 bit 3 City steering mode; Byte 6 bit 4 rear defogger; Byte 7 wheel rotation counter
0x0A18A001169385985Engine Coolant Temp (ECM): Byte 3 Coolant temperature (raw − 40 °C); Bytes 4–5 electrical load
0x0A18A006169385990Engine running flag (Byte 0: 01 running) & vehicle speed (Bytes 2–3)
0x0A28A000170434560Vehicle speed (Bytes 0–1) & wheel rotation counter (Byte 3)
0x0C1CA000203202560Start&Stop & seatbelt / front door status (Byte 2 bit 2 doors/seatbelt, bit 5 S&S active)
0x0C28A000203988992Body computer date & time in BCD/hex: Byte 0 hour, Byte 1 min, Byte 2 day, Byte 3 month, Bytes 4–5 year

Fiat 29-Bit UDS Diagnostic IDs & Key DIDs

Fiat C-CAN modules use ISO 15765-2 normal fixed 29-bit addressing (tester SA 0xF1, functional broadcast 0x18DB33F1). Important implementation note: Magneti Marelli IAW 5SF9 ECUs on the Grande Punto reject padded 8-byte UDS frames — the CAN DLC must match the exact ISO-TP payload length, and standard OBD-II Mode 01–0A requests are not answered on non-EOBD markets.

Request ID Response ID Target Module Documented UDS DIDs (Service 0x22)
0x18DA10F10x18DAF110Engine ECU (0x10)0x1000 RPM (raw ÷ 4), 0x1003 Coolant temp (raw − 40 °C), 0x1004 Battery (raw ÷ 10 V), 0x181F MAP (mbar), 0x186B Target idle (raw ÷ 4 rpm), 0x1956 Baro (mbar), 0xF187 Part number
0x18DA28F10x18DAF128ABS / ESP (0x28)0x0885 Steering angle (16-bit signed ÷ 16 deg), 0x0889 Handbrake switch (bit 0)
0x18DA30F10x18DAF130Steering Column / EPS (0x30)0x0948 Steering angle, battery voltage (×16), vehicle speed, engine running / City mode / MIL flags
0x18DA40F10x18DAF140Body Computer / BCM (0x40)Body status, lighting, central locking, and proxy configuration

Sources