Removed text is struck through; added text is highlighted.
Adaptronic eSel040 is a Select-series vehicle plug-in programmable engine-management ECU. The surviving manufacturer guide identifies the intended application as Mazda RX-7 FC Series 5 (1989–1991) 13B single turbo. Adaptronic eSel040 application and installation guide.
Identification and application
Confirm the case label and part number, original ECU and loom connector, engine, market and any vehicle-specific equipment against the guide before purchase or installation. Vehicle wiring can vary, and a shared plug shape does not establish pin compatibility.
Software and installation
The Select family uses Adaptronic WARI software, which is listed in Haltech’s legacy Adaptronic downloads archive. Use the matching eSel040 guide and application-specific basemap; the guide documents installation, configuration and pin references. A plug-in ECU still requires configuration and tuning for the actual engine and equipment.
Wiring and pinout
The manufacturer eSel040 guide contains the model and application-specific connector information. Positions and functions can change by application, and factory function and Adaptronic function are separate columns in the guide. The documented connector groups are transcribed below; verify the source and connector viewpoint before use.
Support and sources
Haltech states that Adaptronic operations ended in 2022. Refer to its Adaptronic notice and archived guides, and confirm current support and compatibility for used hardware. A verified product photograph for this exact part has not yet been added.
Adaptronic manufacturer index
Manufacturer connector table
Transcribed from the model-specific Adaptronic installation guide linked above. The guide gives pin numbering from the loom side of the plug, looking into the ECU. A dash denotes a blank source cell. The source says NC is no connection in the factory loom and an empty Adaptronic column means no connection to the Adaptronic ECU. The oil-metering pump outputs are paired as described in the comments.
Factory pinFactory functionAdaptronic functionInstallation notes4ZGrn / Red Injector (Rear Secondary)Injector Output 4—4YGrn / Blk Injector (Rear Primary)Injector Output 3—4XGrn / Wht Injector (Front Secondary)Injector Output 2—4WGrn / Red Injector (Front Primary)Injector Output 1—4VBlk / Red Oil Metering Pump 1 barAux Output 7 barInverse of 4T.4UBlk / Grn Oil Metering Pump 2 barAux Output 8 barInverse of 4S.4TBlk / Blu Oil Metering PumpAux Output 7—4SBlk / Ora Oil Metering Pump 2Aux Output 8—4RBlu / Wht Boost ControlAux Output 3—4QBlu / Grn Idle Control Solenoid ValveAux Output 2—4PWht / Blu Defogger input——4OYel / Blk Blower inputDigital Input 7Electrical load.4NGrn / Red unknown function——4MBlu / Ora PRC Solenoid Valve——4LWht / Grn Headlight inputDigital Input 8Electrical load.4KBrn Fuel pump (circuit opening) relayAux Output 5—4JAWS Solenoid Valve——4ISplit Air Solenoid Valve——4HRed Crankshaft Sensor -veSGNDSensor wires white and white/black; loom red and green.4GWht Crank Pos Sensor G (2 tooth)CAS 2 inputSensor green; loom white.4FNC——4EBlu Crank Pos Sensor NE (24 tooth)CAS 1 inputSensor red; loom blue.4DBrn / Blk Sensor GroundSGND—4CBlk Chassis GroundPGND—4BBlk / Wht Chassis GroundPGND—4ABlk / Wht Chassis GroundPGND—3PBlu / Ryel - Relief Solenoid ValveAux Output 4—3OBlu / Red Switch Solenoid ValveAux Output 1—3NBlu Port Air Solenoid Valve—Optional front-right wheel speed.3MWht Knock SensorKnock input—3LGrn Intake Air Temperature SenorMAT input—3KGrn / Ora MAF signalAux Temp—3JBrn / Red Power GNDPGND—3IBrn / Wht TPS 5VTPS 5V—3HGrn / Yel MAP signalMAP signal input—3GBlk / Grn TPS Full RangeTPS signal input—3FGrn / Red TPS Narrow RangeSVSS1Optional flex fuel or front-left wheel speed.3EGrn / Wht Coolant Temp SensorECT—3D———3CBlk Oxygen Sensor InputO2 signal Input—3BGrn / Red Sensor GNDSGND—3AGrn / Red Oil Metering Pump SensorExt In—1V / VBlu IGF ignition feedback——1U / UBrn / Yel Mileage Sensor 2——1T / TBlk / Blu brake light switchDigital Input 5—1S / SRed / Blk Fog Lamp SwitchDigital Input 6Electrical load.1R / RGrn / Blk Neutral SwitchDigital Input 2—1Q / QGrn / Red Clutch SwitchDigital Input 1—1P / PBlk / Yel Heat Hazard——1O / OBlu / Ora A/C requestDigital Input 4Inverted digital input 4; also controls A/C clutch.1N / NLtGrn / Blk Steering Pressure SensorDigital Input 3Engine load.1M / MBlu SpeedometerMVSS1Optional rear-left wheel speed.1L / LBlk / Wht A/C RelayAC Relay OutputControlled by A/C request.1K / KGrn / Red Fuel Pump Relay (Speed)——1J / JBrn / Yel Igniter Trailing selectIgniter Output 3Direct-fire conversion: rotor 2 trailing.1I / IOra Data Link ConnectorIgniter Output 4Optional rotor 2 leading ignition; diagnostic orange wire; sacrifices switch-solenoid output.1H / HBrn Igniter LeadingIgniter Output 1Direct-fire conversion: rotor 1 leading.1G / GBrn Igniter TrailingIgniter Output 2Direct-fire conversion: rotor 1 trailing.1F / FYel / Blk Data Link ConnectorMVSS2Optional rear-right wheel speed.1E / ECheck lightAux Ouptut 6—1D / DYel Data Link ConnectorCAS 3, for flex fuelDiagnostic yellow wire.1C / CBlk / Red starter interlock switch——1B / BBlk / Wht Main Relay+12 IgnitionFrom EFI relay.1A / ABlu / Red constant powerConst 12VFused battery supply.Manufacturer photographAdaptronic eSel040 ECU pictured in its manufacturer installation guide, page 1; reproduced with permission.Factory pinFactory functionAdaptronic functionManufacturer notes4ZGrn / Red Injector (Rear Secondary)Injector Output 4—4YGrn / Blk Injector (Rear Primary)Injector Output 3—4XGrn / Wht Injector (Front Secondary)Injector Output 2—4WGrn / Red Injector (Front Primary)Injector Output 1—4VBlk / Red Oil Metering Pump 1 barAux Output 7 barAlways functions opposite to 4T4UBlk / Grn Oil Metering Pump 2 barAux Output 8 barAlways functions opposite to 4S4TBlk / Blu Oil Metering PumpAux Output 7—4SBlk / Ora Oil Metering Pump 2Aux Output 8—4RBlu / Wht Boost ControlAux Output 3—4QBlu / Grn Idle Control Solenoid ValveAux Output 2—4PWht / Blu Defogger input——4OYel / Blk Blower inputDigital Input 7Electrical load input4NGrn / Red unknown function——4MBlu / Ora PRC Solenoid Valve——4LWht / Grn Headlight inputDigital Input 8Electrical load input4KBrn Fuel pump (circuit opening) relayAux Output 5—4JAWS Solenoid Valve——4ISplit Air Solenoid Valve——4HRed Crankshaft Sensor -veSGNDConnects to “white” and “white/black” on the sensor itself (red and green in the loom)4GWht Crank Pos Sensor G (2 tooth)CAS 2 inputConnects to “green” on the sensor itself (white in the loom)4FNC——4EBlu Crank Pos Sensor NE (24 tooth)CAS 1 inputConnects to “red” on the sensor itself (blue in the loom)4DBrn / Blk Sensor GroundSGND—4CBlk Chassis GroundPGND—4BBlk / Wht Chassis GroundPGND—4ABlk / Wht Chassis GroundPGND—3PBlu / Ryel - Relief Solenoid ValveAux Output 4—3OBlu / Red Switch Solenoid ValveAux Output 1—3NBlu Port Air Solenoid Valve—If converting to 4 wheel speed inputs, this should be the front right wheel speed input.3MWht Knock SensorKnock input—3LGrn Intake Air Temperature SenorMAT input—3KGrn / Ora MAF signalAux Temp—3JBrn / Red Power GNDPGND—3IBrn / Wht TPS 5VTPS 5V—3HGrn / Yel MAP signalMAP signal input—3GBlk / Grn TPS Full RangeTPS signal input—3FGrn / Red TPS Narrow RangeSVSS1Can be used for flex fuel sensor input or front left wheel speed input for traction control3EGrn / Wht Coolant Temp SensorECT—3D———3CBlk Oxygen Sensor InputO2 signal Input—3BGrn / Red Sensor GNDSGND—3AGrn / Red Oil Metering Pump SensorExt In—1V / VBlu IGF ignition feedback——1U / UBrn / Yel Mileage Sensor 2——1T / TBlk / Blu brake light switchDigital Input 5—1S / SRed / Blk Fog Lamp SwitchDigital Input 6Electrical load input1R / RGrn / Blk Neutral SwitchDigital Input 2—1Q / QGrn / Red Clutch SwitchDigital Input 1—1P / PBlk / Yel Heat Hazard——1O / OBlu / Ora A/C requestDigital Input 4This triggers digital input 4, after inversion, and also drives the A/C clutch output1N / NLtGrn / Blk Steering Pressure SensorDigital Input 3Engine load input1M / MBlu SpeedometerMVSS1If converting to 4 wheel speed inputs, this should be the rear left wheel speed input.1L / LBlk / Wht A/C RelayAC Relay OutputDriven by AC input1K / KGrn / Red Fuel Pump Relay (Speed)——1J / JBrn / Yel Igniter Trailing selectIgniter Output 3If converting to direct fire, this becomes the trailing output for rotor 2.1I / IOra Data Link ConnectorIgniter Output 4Not used on factory, but can use this pin for conversion to direct fire for leading ignition, rotor 2 (you lose the switch solenoid output then). This wire comes out at the diagnostic connector (orange wire)1H / HBrn Igniter LeadingIgniter Output 1When converting to direct fire, this output becomes the trigger for leading ignition on rotor 1 (front)1G / GBrn Igniter TrailingIgniter Output 2If converting to direct fire, this becomes the trailing output for rotor 1.1F / FYel / Blk Data Link ConnectorMVSS2If converting to 4 wheel speed inputs, this should be the rear right wheel speed input1E / ECheck lightAux Ouptut 6—1D / DYel Data Link ConnectorCAS 3, for flex fuelThis pin comes out at the the diagnostic connector (yellow wire).1C / CBlk / Red starter interlock switch——1B / BBlk / Wht Main Relay+12 IgnitionOutput from EFI relay1A / ABlu / Red constant powerConst 12VStraight from battery via fuse
Rendered revisions
Open each version to inspect formatting, tables and photographs.
Revision 3: Adaptronic eSel040
Adaptronic eSel040 is a Select-series vehicle plug-in programmable engine-management ECU. The surviving manufacturer guide identifies the intended application as Mazda RX-7 FC Series 5 (1989–1991) 13B single turbo. Adaptronic eSel040 application and installation guide.
Identification and application
Confirm the case label and part number, original ECU and loom connector, engine, market and any vehicle-specific equipment against the guide before purchase or installation. Vehicle wiring can vary, and a shared plug shape does not establish pin compatibility.
Software and installation
The Select family uses Adaptronic WARI software, which is listed in Haltech’s legacy Adaptronic downloads archive. Use the matching eSel040 guide and application-specific basemap; the guide documents installation, configuration and pin references. A plug-in ECU still requires configuration and tuning for the actual engine and equipment.
Wiring and pinout
The manufacturer eSel040 guide contains the model and application-specific connector information. Positions and functions can change by application, and factory function and Adaptronic function are separate columns in the guide. The documented connector groups are transcribed below; verify the source and connector viewpoint before use.
Support and sources
Haltech states that Adaptronic operations ended in 2022. Refer to its Adaptronic notice and archived guides, and confirm current support and compatibility for used hardware. A verified product photograph for this exact part has not yet been added.
Transcribed from the model-specific Adaptronic installation guide linked above. The guide gives pin numbering from the loom side of the plug, looking into the ECU. A dash denotes a blank source cell. The source says NC is no connection in the factory loom and an empty Adaptronic column means no connection to the Adaptronic ECU. The oil-metering pump outputs are paired as described in the comments.
Factory pin
Factory function
Adaptronic function
Manufacturer notes
4Z
Grn / Red Injector (Rear Secondary)
Injector Output 4
—
4Y
Grn / Blk Injector (Rear Primary)
Injector Output 3
—
4X
Grn / Wht Injector (Front Secondary)
Injector Output 2
—
4W
Grn / Red Injector (Front Primary)
Injector Output 1
—
4V
Blk / Red Oil Metering Pump 1 bar
Aux Output 7 bar
Always functions opposite to 4T
4U
Blk / Grn Oil Metering Pump 2 bar
Aux Output 8 bar
Always functions opposite to 4S
4T
Blk / Blu Oil Metering Pump
Aux Output 7
—
4S
Blk / Ora Oil Metering Pump 2
Aux Output 8
—
4R
Blu / Wht Boost Control
Aux Output 3
—
4Q
Blu / Grn Idle Control Solenoid Valve
Aux Output 2
—
4P
Wht / Blu Defogger input
—
—
4O
Yel / Blk Blower input
Digital Input 7
Electrical load input
4N
Grn / Red unknown function
—
—
4M
Blu / Ora PRC Solenoid Valve
—
—
4L
Wht / Grn Headlight input
Digital Input 8
Electrical load input
4K
Brn Fuel pump (circuit opening) relay
Aux Output 5
—
4J
AWS Solenoid Valve
—
—
4I
Split Air Solenoid Valve
—
—
4H
Red Crankshaft Sensor -ve
SGND
Connects to “white” and “white/black” on the sensor itself (red and green in the loom)
4G
Wht Crank Pos Sensor G (2 tooth)
CAS 2 input
Connects to “green” on the sensor itself (white in the loom)
4F
NC
—
—
4E
Blu Crank Pos Sensor NE (24 tooth)
CAS 1 input
Connects to “red” on the sensor itself (blue in the loom)
4D
Brn / Blk Sensor Ground
SGND
—
4C
Blk Chassis Ground
PGND
—
4B
Blk / Wht Chassis Ground
PGND
—
4A
Blk / Wht Chassis Ground
PGND
—
3P
Blu / Ryel - Relief Solenoid Valve
Aux Output 4
—
3O
Blu / Red Switch Solenoid Valve
Aux Output 1
—
3N
Blu Port Air Solenoid Valve
—
If converting to 4 wheel speed inputs, this should be the front right wheel speed input.
3M
Wht Knock Sensor
Knock input
—
3L
Grn Intake Air Temperature Senor
MAT input
—
3K
Grn / Ora MAF signal
Aux Temp
—
3J
Brn / Red Power GND
PGND
—
3I
Brn / Wht TPS 5V
TPS 5V
—
3H
Grn / Yel MAP signal
MAP signal input
—
3G
Blk / Grn TPS Full Range
TPS signal input
—
3F
Grn / Red TPS Narrow Range
SVSS1
Can be used for flex fuel sensor input or front left wheel speed input for traction control
3E
Grn / Wht Coolant Temp Sensor
ECT
—
3D
—
—
—
3C
Blk Oxygen Sensor Input
O2 signal Input
—
3B
Grn / Red Sensor GND
SGND
—
3A
Grn / Red Oil Metering Pump Sensor
Ext In
—
1V / V
Blu IGF ignition feedback
—
—
1U / U
Brn / Yel Mileage Sensor 2
—
—
1T / T
Blk / Blu brake light switch
Digital Input 5
—
1S / S
Red / Blk Fog Lamp Switch
Digital Input 6
Electrical load input
1R / R
Grn / Blk Neutral Switch
Digital Input 2
—
1Q / Q
Grn / Red Clutch Switch
Digital Input 1
—
1P / P
Blk / Yel Heat Hazard
—
—
1O / O
Blu / Ora A/C request
Digital Input 4
This triggers digital input 4, after inversion, and also drives the A/C clutch output
1N / N
LtGrn / Blk Steering Pressure Sensor
Digital Input 3
Engine load input
1M / M
Blu Speedometer
MVSS1
If converting to 4 wheel speed inputs, this should be the rear left wheel speed input.
1L / L
Blk / Wht A/C Relay
AC Relay Output
Driven by AC input
1K / K
Grn / Red Fuel Pump Relay (Speed)
—
—
1J / J
Brn / Yel Igniter Trailing select
Igniter Output 3
If converting to direct fire, this becomes the trailing output for rotor 2.
1I / I
Ora Data Link Connector
Igniter Output 4
Not used on factory, but can use this pin for conversion to direct fire for leading ignition, rotor 2 (you lose the switch solenoid output then). This wire comes out at the diagnostic connector (orange wire)
1H / H
Brn Igniter Leading
Igniter Output 1
When converting to direct fire, this output becomes the trigger for leading ignition on rotor 1 (front)
1G / G
Brn Igniter Trailing
Igniter Output 2
If converting to direct fire, this becomes the trailing output for rotor 1.
1F / F
Yel / Blk Data Link Connector
MVSS2
If converting to 4 wheel speed inputs, this should be the rear right wheel speed input
1E / E
Check light
Aux Ouptut 6
—
1D / D
Yel Data Link Connector
CAS 3, for flex fuel
This pin comes out at the the diagnostic connector (yellow wire).
1C / C
Blk / Red starter interlock switch
—
—
1B / B
Blk / Wht Main Relay
+12 Ignition
Output from EFI relay
1A / A
Blu / Red constant power
Const 12V
Straight from battery via fuse
Revision 5: Adaptronic eSel040
Adaptronic eSel040 is a Select-series vehicle plug-in programmable engine-management ECU. The surviving manufacturer guide identifies the intended application as Mazda RX-7 FC Series 5 (1989–1991) 13B single turbo. Adaptronic eSel040 application and installation guide.
Identification and application
Confirm the case label and part number, original ECU and loom connector, engine, market and any vehicle-specific equipment against the guide before purchase or installation. Vehicle wiring can vary, and a shared plug shape does not establish pin compatibility.
Software and installation
The Select family uses Adaptronic WARI software, which is listed in Haltech’s legacy Adaptronic downloads archive. Use the matching eSel040 guide and application-specific basemap; the guide documents installation, configuration and pin references. A plug-in ECU still requires configuration and tuning for the actual engine and equipment.
Wiring and pinout
The manufacturer eSel040 guide contains the model and application-specific connector information. Positions and functions can change by application, and factory function and Adaptronic function are separate columns in the guide. The documented connector groups are transcribed below; verify the source and connector viewpoint before use.
Support and sources
Haltech states that Adaptronic operations ended in 2022. Refer to its Adaptronic notice and archived guides, and confirm current support and compatibility for used hardware. A verified product photograph for this exact part has not yet been added.
Transcribed from the model-specific Adaptronic installation guide linked above. The guide gives pin numbering from the loom side of the plug, looking into the ECU. A dash denotes a blank source cell. The source says NC is no connection in the factory loom and an empty Adaptronic column means no connection to the Adaptronic ECU. The oil-metering pump outputs are paired as described in the comments.
Factory pin
Factory function
Adaptronic function
Installation notes
4Z
Grn / Red Injector (Rear Secondary)
Injector Output 4
—
4Y
Grn / Blk Injector (Rear Primary)
Injector Output 3
—
4X
Grn / Wht Injector (Front Secondary)
Injector Output 2
—
4W
Grn / Red Injector (Front Primary)
Injector Output 1
—
4V
Blk / Red Oil Metering Pump 1 bar
Aux Output 7 bar
Inverse of 4T.
4U
Blk / Grn Oil Metering Pump 2 bar
Aux Output 8 bar
Inverse of 4S.
4T
Blk / Blu Oil Metering Pump
Aux Output 7
—
4S
Blk / Ora Oil Metering Pump 2
Aux Output 8
—
4R
Blu / Wht Boost Control
Aux Output 3
—
4Q
Blu / Grn Idle Control Solenoid Valve
Aux Output 2
—
4P
Wht / Blu Defogger input
—
—
4O
Yel / Blk Blower input
Digital Input 7
Electrical load.
4N
Grn / Red unknown function
—
—
4M
Blu / Ora PRC Solenoid Valve
—
—
4L
Wht / Grn Headlight input
Digital Input 8
Electrical load.
4K
Brn Fuel pump (circuit opening) relay
Aux Output 5
—
4J
AWS Solenoid Valve
—
—
4I
Split Air Solenoid Valve
—
—
4H
Red Crankshaft Sensor -ve
SGND
Sensor wires white and white/black; loom red and green.
4G
Wht Crank Pos Sensor G (2 tooth)
CAS 2 input
Sensor green; loom white.
4F
NC
—
—
4E
Blu Crank Pos Sensor NE (24 tooth)
CAS 1 input
Sensor red; loom blue.
4D
Brn / Blk Sensor Ground
SGND
—
4C
Blk Chassis Ground
PGND
—
4B
Blk / Wht Chassis Ground
PGND
—
4A
Blk / Wht Chassis Ground
PGND
—
3P
Blu / Ryel - Relief Solenoid Valve
Aux Output 4
—
3O
Blu / Red Switch Solenoid Valve
Aux Output 1
—
3N
Blu Port Air Solenoid Valve
—
Optional front-right wheel speed.
3M
Wht Knock Sensor
Knock input
—
3L
Grn Intake Air Temperature Senor
MAT input
—
3K
Grn / Ora MAF signal
Aux Temp
—
3J
Brn / Red Power GND
PGND
—
3I
Brn / Wht TPS 5V
TPS 5V
—
3H
Grn / Yel MAP signal
MAP signal input
—
3G
Blk / Grn TPS Full Range
TPS signal input
—
3F
Grn / Red TPS Narrow Range
SVSS1
Optional flex fuel or front-left wheel speed.
3E
Grn / Wht Coolant Temp Sensor
ECT
—
3D
—
—
—
3C
Blk Oxygen Sensor Input
O2 signal Input
—
3B
Grn / Red Sensor GND
SGND
—
3A
Grn / Red Oil Metering Pump Sensor
Ext In
—
1V / V
Blu IGF ignition feedback
—
—
1U / U
Brn / Yel Mileage Sensor 2
—
—
1T / T
Blk / Blu brake light switch
Digital Input 5
—
1S / S
Red / Blk Fog Lamp Switch
Digital Input 6
Electrical load.
1R / R
Grn / Blk Neutral Switch
Digital Input 2
—
1Q / Q
Grn / Red Clutch Switch
Digital Input 1
—
1P / P
Blk / Yel Heat Hazard
—
—
1O / O
Blu / Ora A/C request
Digital Input 4
Inverted digital input 4; also controls A/C clutch.